PROG.MIX Setting in AT9S Pro/AT10II Transmitter

[@DevonsWorkshop]

Couldn't figure out how to get to the ^ rate in a mix. Never occurred to me to use the joystick because everything else is configured with the jog wheel. Thank you for this video. Answered exactly the question I was looking for.

[@Radiolink_official]

Great to know you figure it out. If any question when using RadioLink products please feel free to contact us. Our email is: [e-mail]

[@StefanBacon]

Thank you! this helped me set up auto leveling on my ;1:14 Takeuchi TL12V2 track loader!

[@Radiolink_official]

Great to know it is helpful to you. If any question about RadioLink products please feel free to contact us. Our email is: [e-mail]

[@StefanBacon]

I do have another question, is it possible to "rate control" a servo? I want to use the stick to "trim" the servo end to end, where stick center is "hold position" and left or right is increase or decrease angle. If the radio can do it, it will save me a lot of trouble programming a microcontroller to intercept and interpret the signal.

[@Radiolink_official]

@@StefanBacon Hi, sir. Sorry we do not clearly understand what you mean. Do you want to make the two sticks return to center automatically? If yes, you can check this video tutorial. kzbin.info/www/bejne/p3TRi5-knrZqb6s If any question please feel free to contact us. Our email is: [e-mail]

[@blackdawgrc8425]

Good morning radiolink! Beautiful video, but I can barely hear what she is saying! My question is about program mixing settings 🤔 on the radiolink at10ii 12-channel transmitter! Because I have and loved that radio! Here's my question? Can I program mixing? Channel 3 is the master! And Channel 2 is the slave? And Channel 1 is the master! And Channel 4 is the slave! Can this program mixing can work on the radiolink at10ii 12-channel transmitter??? Your professional feedback is always appreciated! Thank you.

[@Radiolink_official]

Hello, sir. Yes. It works. Channel 1-8 can be master, they can also be slave channel. So Channel 3 can be the master! And Channel 2 can be the slave. And Channel 1 can be the master, and Channel 4 can be the slave. If there is any question when using our products, please feel free to contact us. Our email is [e-mail]

[@Radiolink_official]

@Freedom1775 Hello, sir. The slave channel depends which channel you connect the servo to. For example, there are two motors. One motor is connected to channel 3, the other motor is connected to channel 8. The channel 3 is the master channel, the channel 8 is the sleve channel.

[@xristoslc]

Thanks!

[@Radiolink_official]

Our pleasure. Any question when using RadioLink products please feel free to contact us. Our email is: [e-mail]

[@muhammadrashid6663]

Good 👍

[@Radiolink_official]

Thank you

[@rc_farmer4866]

Hi Radiolink, I have been trying to mix other channels, such as CH 6 to CH 8, but I can't get it to work. Any help, would be greatly appreciated. Thanks1

[@Radiolink_official]

Hi, sir. May I know what switches did you assign to control channel 6 and channel 8? You need to assign the similar switch for both of two channels. For example, assign two 3 position switches to control channel 6 and channel 8. And the two switches need to be put in the middle position. If there is still any question, could you please take a video to us? It may be helpful for us to know what happened. Our email is: [e-mail]

[@Vegatermik]

I can't find such a RADIOLINK AT9S or AT10II presentation about the DIFFERENT THRUST drive. Controlling a model airplane using the thrust difference of two propulsion engines. Your presentation will be interesting, it should show the connection of the batteries (battery) with the receiver and ESC's with the configuration of the RADIOLINK transmitter.

[@Radiolink_official]

Hello, sir. Could you please provide us with more detailed information? What model is your airplane? Do you want the aile-diff function? If yes, you can set it in AT9S Pro or AT10II. If any question please feel free to contact us. Our email is [e-mail]

[@Vegatermik]

@@Radiolink_official I am an AT9S user and I use this radio with glow engine glider flights. However, I am interested in the option for an future model with two electric motors. It's about differential thrust. I bought your radio, so I will be grateful for instructions on how to configure the settings on the radio along with the ability to operate twice electric engine with the elevator and rudder. General settings are enough for me, as for example in this video kzbin.info/www/bejne/bZDRg3ahf9eda6s Elev&Rudder do not have to be mixed. I see many videos on YT showing how to set differential thrust. Even other customers ask you about it...

[@Vegatermik]

@@Radiolink_official I see that in that video I linked to, the flying model doesn't use rudder and elevator. I guess the whole idea of different thrust is that we only use engines without rudder and elevator. And if so, can I use the V-TAIL mixer and replace the servos with electric motors in the system: two motors, two ESCs, one battery. Maybe you will be able to show such a movie with the settings in AT9S or other AT9S Pro or AT10II, after all, these settings are similar. I'm talking about models built, for example, of light depron.

[@Radiolink_official]

@@Vegatermik Hello, sir. You can achieve a Yaw turn by PROG,MIX. For example, you set the percent ot the other channel to -100%. Could you please check this tutorial too? kzbin.info/www/bejne/rXecdp-ga6uKd7M (It is not AT9S Pro in the video, but the setting is the same) That is to say, you can get the function you want by setting the rate to -100% to make the direction of the two channel different. If there is any question ,please feel free to contact me.

[@Vegatermik]

@@Radiolink_official you know that you can afford a better presentation on mixing engines in RC light weight planes. Thanks for the link and your suggestions. It's better because I didn't get any information before. It is a pity that I have to learn the topic of differential thrust from your competition. You have a woman who very thoroughly explains various problems on YT. It shows and explains things very well. It was helpful, but you can do better because Radiolinka deserves it.

[@AmiirBro]

Hi dear friend How to set up steering direction When I try to turn left or right rc Car It's makes Weird noise Thank you

[@Radiolink_official]

Hi, sir. Are you using AT9S Pro or AT10II? Could you please take a video to us to show the problem? It will be helpful for us to know what happened and help you solve it. Generally, if there is no problem of servo display in the transmitter, you can check the devices on your car. You can send videos to our email [e-mail]

[@robk2527]

How about showing us how to mix channel 1 and 2 for robotics and track machines..... when you do it the way you can in every other radio it don't work................

[@Radiolink_official]

Hi, sir. The theory of PROG.MIX is the same for all models. You just need to set the value according to your needs. Here is the detailed manual of AT9S Pro for you to better know about the prog.mix: www.radiolink.com/at9spro_manual If there is any question, please feel free to contact us. Our email is [e-mail]

[@АнатолийМульченко]

👍

[@adrianoyuremanu5148]

👋👋👋👏👏👏👏👏👏👏👏👏👏👏👏

[@kasifyldrm1981]

Merhaba kolay gelsin daha önce bu konuda ile ilgili ulaştım size. master CH1 yaptım slave CH5 CH6 CH7 bu 3 kanalı aynı anda bağlayabilirmiyim yada başka bir sistem varmi böyle yapacağım

[@Radiolink_official]

Hi, sir, You can set many prog.mixes at the same time. If any other question please feel free to contact us

[@kasifyldrm1981]

@@Radiolink_official nasıl yapacağım hakkında yardımcı olurmusunuz slave ye 3 kanalı aynı anda bağlı olarak çalıştıracığım konusunda. elinizde kumanda varsa video atabilirmisiniz

[@Radiolink_official]

@@kasifyldrm1981 Hi, sir. Sorry we do not know what you want. We guess you may need to set several prog,mixes. Just need to follow this tutorial to set prog,mixes you want. Can you speak English? If yes, you can send more details on what you want to our email [e-mail]. Then we'll know how to help you.

[@adrianoyuremanu5148]

👋👋👋👏👏👏👏👏🙏🙏

[@lexuanhoang6680]

??? 1:37?

[@Radiolink_official]

Hi, may I know what you mean?