@enduro.mp4880 Hast du die Lager an den beiden Wippen auch schon mal gewechselt? Wie hast du diese sauber rausgekriegt? Dazwischen sind ja noch die Distanzbüchsen, welche ein Auspressen mit einem normalen Spreizer schwieriger machen...
@enduro.mp48806 ай бұрын
Hey, du kannst mit einem kleinen Austreiber das Distanzstück innen minimal runterdrücken und das Lager von Innen herausschlagen. Video dazu ist in Planung:)
@erichbachman73633 жыл бұрын
Wow, thanks for taking the time to make such a detailed video! I learnt alot about the bike's suspension from this and i'm sure other owning or that are considering buying this bike would find this valueble to watch.
@enduro.mp48803 жыл бұрын
Thank you!
@frankbischof62043 жыл бұрын
That's the video i've been waiting for👌Nice job. Thanks guy
@crazylex3102 күн бұрын
how much torque did you put on the damper bolts?
@maksym_go_propain2 ай бұрын
Hey Bro .. frage bei top rocker werden die zwei Washer zsm gebracht oder kommt der 0.25 Washer komplett nach außen bei axle ?
@josephkinnear58023 жыл бұрын
Great video nice to see the suspension like that 👍 Do you have any rub on the frame behind the lower linkage.? Just underneath where the sizing is written. I have and it looks like the lower link has hit it, but after watching how the suspension works this looks very unlikely. Do you think the lower link could hit the frame.?
@enduro.mp48803 жыл бұрын
The scratches come from the mud because there are usually small stones inside, which rub between the frame and the lower link. I also have scratches at that place. Maybe I will do a review of the frame and will show them. I hope this will help amzn.to/3jjZ4Gz
@ralphbartoeckmalermeister4737 Жыл бұрын
Wie hast du das obere Gelenk in den Rahmen bekommen da es so schwer raus ging, wie die unterlegscheiben dazwischen bekommen ?
@enduro.mp4880 Жыл бұрын
Schau das du den Bolzen minimal durch den Rahmen steckst und den ersten Spacer drauf machst. Danach kannst du das gelenk einzestzen und noch den anderen Spacer mit den Finger halten. Etwas schwer zu erklären hoffe es hilft dir😂
@namelessmusik43456 ай бұрын
@@enduro.mp4880 Schaut die Schraube auch minimal rein. Der spacer scheint bei mir "zu dick" zu sein. Sodass die Schraube nicht sauber in die Bohrung einsinkt
@enduro.mp48806 ай бұрын
@@namelessmusik4345 Es gibt verschiedene spacer am Rahmen. Falls du es noch nicht gelößt hast kannst du mir bei Insta eine Dm schreiben:)
@namelessmusik43456 ай бұрын
@@enduro.mp4880 Habe es gelöst tatsächlich schaut die Schraube auch bei anderen so weit raus. Aber danke für deine Antwort
@namelessmusik43456 ай бұрын
At 0:40 Is your screw a little out there? I did everything again when assembling it as I did it, but the screws look a little out.I can't make them in because of this washer
@enduro.mp48806 ай бұрын
Yes. I alway will loosen all screws before disassemble
@andrehoenigsberger3 жыл бұрын
Nice video👍 What kind of frame protection did you use?
@enduro.mp48803 жыл бұрын
I got this one : amzn.to/3pbfzYY
@vino_oz3 жыл бұрын
really good video keep it up😃🤙
@enduro.mp48803 жыл бұрын
Thanks🤝🤝🤝
@dailyshred13693 жыл бұрын
great video! may I just ask what is the size of your dropper post? and your height.
@enduro.mp48803 жыл бұрын
I`am 1,85m tall an have a post with 170mm hub from One Up
@sauber86233 жыл бұрын
Superb video! How old is frame? One full season od riding?
@enduro.mp48803 жыл бұрын
Thanks! since I bought the frame i had no Problems. I just neded to change the bearings in the opper Linkage. And i have to change the Headset. I'am Planing to create a Video from my bike after one Year of using. I think i will do It in the end of this Year.
@eliaswiesenthal34192 жыл бұрын
Wie fest muss man die zwei Schrauben die den Dämpfer befestigen zudrehen?
@enduro.mp4880 Жыл бұрын
Mit 8nm 😁
@MtotheWiZZle9 Жыл бұрын
@@enduro.mp4880 es sind 18 Nm laut Propain, die Angaben findet man auch in der Explosionszeichnung für alle anderen Schrauben
@enduro.mp48806 ай бұрын
@@MtotheWiZZle9 in der Explosionszeichnung gibt es kein Drehmoment mit 18Nm? Die Norm für Dämpferschrauben sind 8Nm in Verbindung mit Loctite bei einer M8 Schraube. Ich spreche hier aber nur vom Spindrift CF. Abgesehen davon sind 18Nm viel zu viel....
@alexmartel4896 Жыл бұрын
nice thanks
@Jskjerning3 жыл бұрын
What grease do you use for the bolts?
@enduro.mp48803 жыл бұрын
Rsp assembly paste Link: amzn.to/3ykxFZt
@enduro.mp48803 жыл бұрын
The assambly paste I only use for thread. For greasing I use a normal Motorex grease