Which bend would you recommend for a supermoto? I have a 450 SMR and need to replace a crashed handlebar; recognize this is MX but I’m not sure what to try out. Thank you 🙏
@Curiouscricket2 жыл бұрын
It shows you riding with them, did you notice better vibration dampening or impact absorption?
@rmatvmc2 жыл бұрын
Honestly, I didn't notice too much from the ODI Podium bars that I use now. They are lighter but as for damping and vibration, it's sixes for me. - Chase
@Shelby8371 Жыл бұрын
Hi Are these more suited for Mx tracks? I’m a woods rider and trails rider. And was wondering was was your thoughts
@rmatvmc Жыл бұрын
These are built around motocross so yes, they are definitely built for the track. If you like to cut your bars down for woods riding, they state that these bars are not meant to be cut down so keep that in mind. - Chase
@zackhinze96842 жыл бұрын
What about putting them on a small adv bike with hand guards? Is it possible with the bar inserts?
@ChookChasersMX2 жыл бұрын
They don’t advise using bar inserts on this bar but Jeff slavens (slavens racing) has a video where he threads the ends for a bar insert.
@Shelby8371 Жыл бұрын
Hi Chase Can you use bar ends with these bars. And are they a good single track woods bar or just suited for the track. 👍
@rmatvmc Жыл бұрын
When you say bar ends, are you referring to full wrap hand guards? Or like the ODI bar ends?
@Shelby8371 Жыл бұрын
@@rmatvmc odi bar ends
@jcbenson0111 ай бұрын
@@rmatvmcI have the same question. Is the ID of the bars standard to accept bar-end plugs and/or hand guards?
@rmatvmc11 ай бұрын
@@jcbenson01 It is not recommended by ProTaper to use bar ends or handguards that mount using expandable mounts.
@ralphgodwin51432 жыл бұрын
Are the SX Race bends back in stock? I keep checking and they’re out of stock on the website.
@rmatvmc2 жыл бұрын
As of 6/17 they are still out of stock in the SX race bend. Have you hit the "email when available" box? That is an easy way to know when they are in stock.
@kill5326 Жыл бұрын
do you know how thick the clamp is in mm i ordered the wrong triple clamp set (22mm) and they are too small would these be 28mm?
@bryceridesbikes Жыл бұрын
They should be 1 1/8" or 31.8mm just like any other oversized bar
@Curiouscricket2 жыл бұрын
Hey Chase, do you know if you can run a ball-bearing style throttle tube with these?
@rmatvmc2 жыл бұрын
Run one on this bar? There is no reason you shouldn't be able to. - Chase
@brettmansfield6 ай бұрын
I'm also wondering this, it looks like the carbon core goes right to the end of the bar so there'd be no room for the bearing/plug end of a alloy/bearing throttle tube.
@michaelanderson17272 жыл бұрын
Can you cut half inch off of each side?
@rmatvmc2 жыл бұрын
No, this handlebar should not be cut down.
@gophop2 жыл бұрын
@@rmatvmc They can't be tapped either then?
@2gunslefty Жыл бұрын
Anyone recommend what pro taper bars will fit with crosss bar on a 2009 kfx900
@rmatvmc Жыл бұрын
Are you talking about a KFX 90 or KFX 700?
@2gunslefty Жыл бұрын
@@rmatvmc 700 ty for helping, I have a few atv’s was in Tennessee and found a 2009 kfX 700 the man bought it new in 2008, and when he was taking it off his truck it landed on the back fender and bent the bars. So I grabbed for 1300$ still had plastic bag attached to handle bars. I had to replace the back fender. It’s that m m red. I found a used one for 350$ it was missing the little gas cover and had graphics on it. They came off.and I have the cover for gas cap. Last thing is bars. I’m going to let like my fiancé son and her ride this.I have a banshee, and a honda trx 450r and warrior , but she can’t get the clutch, so she ends up using my big yellow that I use for yard work. But I want a bar with pads. I always like them on my dirt bikes, atv’s but I can’t tell what bars will work. Without doing risers. Or dash eliminator kit. Kawasaki is new to me but I couldn’t pass. And it’s fast for gas and go. Ty and god bless