Proximity Switch - Introduction, Wiring and Testing

This video shows you the proximity switch used in industrial machines, CNC machines, and other applications. I introduce you to the proximity switch, show you how to wire the proximity switch, and then configure the proximity switch for Mach3.
The equipment and software shown in this video can be found at:
www.buildyourcnc.com
Mach3 Software:
www.buildyourcnc.com/item/con...
Proximity Switch:
www.buildyourcnc.com/item/ele...
Mach3 USB Controller:
buildyourcnc.com/item/electro...
Pokeys57CNC Controller (Mach3 and Mach4):
buildyourcnc.com/item/electro...
24 Vold DC 1 Amp Power Supply:
buildyourcnc.com/item/electro...
My thorough discussions on switch bouncing.
• 12. How to Create a GP...
• 13. Arduino for Produc...
#cnctutorial #cncrouter #proximitysensor #proximitySwitch #limitswitch

[@lamvprtube]

Thank you for taking your time and making these informative capsules. Many of these pieces arrive without instructions. I ask him what happens if we use normal and closed. I ask what happens if we use normal closed proximity switch.

[@jimihills125]

thankyou great video sorted my problem on my printer switch was too far away from, the metal

[@shelleykarijoredjo8421]

Well explained

[@abtappy1190]

Thanks

[@umargul5644]

Great

[@abennacerboulaghmane121]

Thnx for thé vidio pro it is useful

[@PatrickHoodDaniel]

Thanks!

[@chongshenchang9367]

Sir, can you please explain with schematic diagram and components used in electromagnetic accelerator using this sensor which rebel the ball bearing away when it reaches near the inductive coil from it. I needed this for my science project in my college. Please...

[@bishop.somupla]

How to connect Proximity Switch to a EIHONG NK280 with I/O EX9A4 Relay board

[@checktheskies5040]

What about using aluminium as the trigger metal?❤

[@olufemisotunde3868]

Need more explaination when having mutiple proximity on each end . Can they be connected in series

[@PatrickHoodDaniel]

Yes, they can, and I will probably make a video on this. As long as the proximity switch is NC type, the switch can be connected in series. As long as the switch is getting power to enable the sensor, the output signal works very much the same as a typical mechanical switch.

[@olufemisotunde3868]

@@PatrickHoodDaniel can photoelectric sensor be it used for CNC machine. Br100-ddt sensor .I have some in the factory remove from a scrap machine

[@cnc_workbench]

sooooo what happens to the pokeys57 inputs running 5v logic when your prox switch is inactive and you pushing 24v into it?? im hesitant to try as i dont wanna blow up the board.

[@PatrickHoodDaniel]

I didn't make that clear in the video. You would need to use a 5v proximity switch. We have those in stock and will be adding them to that page. Thanks for pointing this out.

[@toddroles3234]

@@PatrickHoodDaniel. I don’t see the 5v proximity switches on your site. I guess I need to buy a level shifting optocoupler to reduce the voltage from switch down to 5v?

[@abiramm129]

Can I use two inductive proximity sensor with the 24 volt power supply

[@PatrickHoodDaniel]

Absolutely! You can use many. The proximity sensor does not draw much current.

[@willlong6275]

How does NC work, show it

[@PatrickHoodDaniel]

Can you elaborate on your question a little?

[@michaelcostello6991]

Was this NPN or PNP sensor ?

[@PatrickHoodDaniel]

This one was probably NPN.

[@51-FS]

2:34