Preamps aren't much more than a pot and switch so why are they so expensive? If you want to learn more, grab a copy of Paul's new book, The Audiophile's Guide. www.amazon.com/Audiophiles-Gu...
Пікірлер: 429
@strobelightstrobelight3 жыл бұрын
Please, can someone give this man an award? I never heard talk and explain someone about audio as that much interesting stories. Will use this channel to learn but also fall sleep (: Congratulations
@theostragonidis75483 жыл бұрын
@I was with your mother What are you smoking bruh
@theostragonidis75483 жыл бұрын
@I was with your mother I'm not talking about cables but about preamps. If you can't hear a difference between a cheap preamp and a NEVE or an AVALON then you must have some hearing damage. It's also pretty easy to see the difference visually if you pull up a frequency analyzer. Stop smoking crack kid.
@Oystein873 жыл бұрын
@I was with your mother Then tell me: Why can I hear a BIG difference in fully blind-test between amps and pre-amps? In some few cases I can also hear differences in speaker cables if it is on a good system. Just because YOU can't hear differences does not mean everyone is alike. Hearing is as variated as there are people.. So to say it's a scam when millions of people hear differences is just a HUGE fail dude ;) It's just as dumb as saying "all cars are exactly the same car"...
@Oystein873 жыл бұрын
@@theostragonidis7548 He is most likely just a lying troll living at his moms house
@Oystein873 жыл бұрын
@I was with your mother Not about what YOU say.. Because you have no clue🤣 And there are tons of evidence that disagrees with you. Actually I can't find a single evidence that does agree with you. It has ALWAYS been proven that there is a difference.. Both by messuring and blind test listening. So just stop trolling. You sound like a twat that claims something just because you have no knowlage.
@SuedwestlichtMusic3 жыл бұрын
I like the way he explains things: friendly & relaxed
@1970borntorun3 жыл бұрын
Paul and Nelson Pass are my favorite Audio Designers. They seem to share the same Philosophy of "doing no harm", and just employing whatever methods/circuitry are best, relative to the Technology available at the time to NOT stand in the way of the Music.
@InsideOfMyOwnMind3 жыл бұрын
Perhaps the best description of what a preamp is for that I have seen.
@rupertanelich549 Жыл бұрын
Paul has an immense skill in explaining very complex issues related to sound production and bringing it to a level that most can understand. Being an audiophile of many years these KZbin clips has definately futher my interest and understanding. Thanks!!
@MS-np6hv3 жыл бұрын
Tall you are a wealth of knowledge about everything high-end audio I could sit and listen to you speak countless hours in a row I'm glad you have a KZbin channel
@HareDeLune3 жыл бұрын
Paul has probably been referred to as 'tall' before, but doubtfully as his proper name. : )
@ChrisWoodBandit3 жыл бұрын
This guy is great! I didnt know what i didnt know about pre amps. I very much enjoyed learning a little about them from this fellow.
@marcus19703 жыл бұрын
There's a twinkle in Paul's eyes every time he says "Pot"
@scottmackey41823 жыл бұрын
That’s because pot is legal in Colorado.
@graxjpg3 жыл бұрын
That usually means one is stoned, but I think Paul has just had enough in his lifetime for the word to have that effect lol.
@progressiveguy99593 жыл бұрын
@@leeharveydarke You are so right!
@progressiveguy99593 жыл бұрын
@Fat Rat It certainly is!
@Jvavolerpareil3 жыл бұрын
@@scottmackey4182 and now in Canada too ! :-)
@SuperMcgenius3 жыл бұрын
Yes, I found the same thing 30 years ago. The BK system of volume control is the best way to go, second is resistor based . The Bryston is a fine preamp.
@killacallahan13 жыл бұрын
Good morning Paul, I've been in cable TV industry for about 30 years. started off as a cable TV installer then service tech then maintenance tech (a maintenance tech is the guy in the bucket truck that works on the whole neighborhood if you will). Then I got into management but I tell you that to say, working on those amplifiers to feed the neighborhoods for cable signal and all the things we have to do to make sure you get gigabytes speed. all the circuitry involved in those amplifiers turning fiber light into RF signal. The price of a BHK preamplifier is hanging on a lot of pole in your city. While I was in management I had to order inventory so I know how much those amplifiers on those poles cost so I understand to engineer something that's great as a BHK its going to cost a lot of money. And take it from the cable guy, "cables matter everyone". just the temperature of a cable will determined the attenuation of our signal, certain size cable determine how much signal I'm going to get on my output, we have to oscillate and shield our cable in order for you guys not to experience interference so you can get that gigabyte speed you want on your internet. And the hardest part of our job is to make sure we have a -50 dB noise floor throughout the whole infrastructure of our network. Cable matters more than you think ok, I'm rambling again. By the way I'm watching too many of your videos because I called my wife Terry twice at the dinner table. Lol have a great day
@marianneoelund29403 жыл бұрын
Do you think it makes sense to take experience with 1GHz-bandwidth signals traveling hundreds of feet through cable, and imply that 20KHz signals traveling 6-20 feet have similar issues? That's rather like insisting that a paper airplane thrown from the top of a skyscraper needs heat shielding like the space shuttle has for its descent from orbit.
@ranbymonkeys23843 жыл бұрын
The biggest part of the cable bill was on Easter Sunday I went outside to see the cable guy finally cleaning up a wired mess that was out at the bottom of the pole for 3 years. Really HOLIDAY PAY is when you people finally do this. Then he cut the wrong wire of course and had to run a new line to my apartment and schedule for the line to be buried and well, I dont have cable anymore. I also had a problem when the oven kicked on my stereo would hummm. I learned about the ground loop eliminator of course this cable company that rhymes with COMCAST had no flippin idea what that was.
@aweidenhammer3 жыл бұрын
I love these vids that seem like a silly question, but aren't and Paul can pull from the history he has to answer with technical information that matters. Thanks!
@khalid9693 жыл бұрын
Thanks for the explanation.
@thomaswipf79863 жыл бұрын
Good explanation on volume control in less than 7min. I'm currently after a Benchmark LA4. Cheers!
@c.w.johson20103 жыл бұрын
I like the way you explain things.
@shkermanshahi3 жыл бұрын
Amazing. Thanks Paul!
@harseybaber3 жыл бұрын
A great question and and a great answer. Excellent!
@rigorhead013 жыл бұрын
Absolutely love these explanation videos!
@TheJosa0073 жыл бұрын
I love your videos there is always something I can learn.
@tommibjork3 жыл бұрын
Impedance is so important. So many sound "engineers" nowadays don't know their electronics. Many things is made simple but things go down hill when you start assuming everything goes. Worse when those advices are passed on in the forums... ☺️
@Remixed_By_Mus-T3 жыл бұрын
I really like your videos. You can learn so many things
@Channel-cm7yc Жыл бұрын
I love it when Paul gets riled up! 😅😅
@PDCRed3 жыл бұрын
Fantastic explanation 👍
@dengony3 жыл бұрын
I don't know why this video was recommended to me but now I need to know everything about preamps.
@holliswong85193 жыл бұрын
Dam you law of physics. It’s bad for my wallet.
@biula32783 жыл бұрын
Speaking of high quality (and therefore expensive) preamps sitting in front of a vintage Studer desk is a convincing way of do it !
@wilcalint3 жыл бұрын
IMO Paul did a very good job describing this.. Bravo Paul
@MlleEclipsada3 жыл бұрын
La mejor intro a los preamps, gracias maestro, saludos de Argentina
@stevesnipes41603 жыл бұрын
Paul, You are the best bro. I will get your PS audio direct stream. Love the way you represent things. Love you bro. Much love and success to you Paul.
@mapoulin3003 жыл бұрын
very good description, I sure agree with him (and I often don't).
@itisjustacommentАй бұрын
Amazing video. I learnt so much .
@TheMirolab3 жыл бұрын
I have very fond memories of my PS Audio 4.6 preamp from 1989..... It had passive and active modes, and what Paul describes is exactly what I experienced. Passive was super transparent, but lacking some oomph. Kicking in the gain gave it life and dynamics, at the loss of some transparency. Sadly it had some reliability issues, noisy switches, and also was not remote control. I switched to an Adcom preamp. I liked the Adcom fine, but it was never as sweet sounding as the PS.
@AstonMartinfan23 жыл бұрын
I've got a 4.6 as my main preamp at the moment. Love that thing, no reliability issues so far. Definitely understand the need to swap though I don't mind the lack of a remote.
@jimmy_jamesjams_a_lot41713 жыл бұрын
The last time I watched a video like this, I was off scouring the far reaches of the web, all in search for anything I could find about making your own voltage regulators. I was interested in a regulator that I could really drain the current from, since commercially available regulators max out at about one Ampere. I find the man who found the same rabbit hole before me and did the real digging. His name is Walt Jung and he did more than build a discrete regulator. He ran multiple regulators of differing topographies through whatever paces he could and wrote some good papers and probably even won an honorary degree or three, dubbing him the Grand Poo-Bah of discreet voltage regulators. I still have yet to try out any of his regulators, having discovered the linear power supplies of Condor, International, and Power One. Which all three seem to be the same power supplies made in Oxnard and yet they go by three different names. So now I’m gonna be off searching probably about the potential of wiring my own transformers, maybe?! THANKS FOR SHARING!!
@BoudewijnvanHouten7 ай бұрын
Very good answer from the kindest man in Audio IMO. Mark Levinson ML-7 pre-amplifier did obtain this balance between straight wire with pot (very expensive Spectrol Series 100 wirewound and later very expensive Penny +Giles RF15 plastic conductive) and bufferstage. One of the best (old) pre-amps ever built and expensive also ($ 4,000.00 in 1981).
@biswajitbasu7478 ай бұрын
Nicely explained!! Thank you 😊
@earfors3 жыл бұрын
❤️❤️❤️❤️ I wouldn’t let go of my hand-built tube preamp for anything less than 500k. Love your videos Paul.
@jackblackwhole3 жыл бұрын
I can sit here and just listen to Paul lecture for hours on end.
@wayman103 жыл бұрын
Very nice explanation.
@hang-sangitch3 жыл бұрын
Thank you this was very informative
@PinballLunatic3 жыл бұрын
Spot on explanation, got it!
@grahamstrahle40103 жыл бұрын
Really excellent explanation.
@killacallahan13 жыл бұрын
Now that's how you answer that one Paul, great answer.
@TheNexusComplex3 жыл бұрын
Quality will cost ya no matter the application. Thanks Mr. McGowan. Excellent explanation.
@simonhenstock62443 жыл бұрын
A good phono stage is worth its weight in gold and doesn't have to break the bank. I use a NAD PP2e which retails for about £100 and it was a real game-changer for my TT. My Sony LX-300USB is at the lower end of the TT market but I wanted to persist with it because I prefer an automatic TT to manual. A separate phono stage and an elliptical stylus turned the weak, distortion-filled sound into punchy bass and detailed sound. If the separate phono stage hadn't worked out, I would have given up on this TT and gone for something a bit more upmarket but that little box makes a bigger difference than most people realise.
@williemckinney21683 жыл бұрын
I love the passion in your voice when you explain everything, if it wasn't for you Paul the love affair I have with music would be mediocre at best! Hope to visit PS audio when we get the all clear from the CDC. Take care 🙂
@TsoneMedia3 жыл бұрын
Nicely said , love it
@georgedesa72553 жыл бұрын
Love your explanations and their basis in facts supported by experience. That said, I also like your naturalness. I have to note that you must have just had a trim - the video pics out the cuttings on your shirt - just makes you human like all of us. :)
@ebroadnax13 жыл бұрын
Curious. Can you use the speaker outs of a receiver (say left and right) to drive a couple of bass shakers while running all pre-outs to a separate amplifier?
@michaelvanda67303 жыл бұрын
Paul have two considered using battery supply for your input stage? My ASR Emitter has this design.
@ctbarker3213 жыл бұрын
It's called the PS Audio Source Preamp. With jumpers you could switch between passive and active. It was a kit. I built one. I still own it.
@SiikPros3 жыл бұрын
Love your humor!
@mdr46703 жыл бұрын
The USA made Schiit Freya and Freya + are highly praised in professional and user reviews and sell for $600 and $899 respectively.
@psysword10 ай бұрын
I returned it for Vincent preamp. Well engineered.
@ruderuda3 жыл бұрын
Amazing, thanks!
@MikeG-js1jt3 жыл бұрын
I think I would feel much more comfortable getting an answer to this question from somebody who is not directly in the industry of selling preamps
@crysstoll11913 жыл бұрын
😀
@MikeG-js1jt3 жыл бұрын
@John Siket I would say it's an explanation but I wouldn't say it's a great explanation I would say it's one of many possible explanations for why so much money is charged for many of these preamps the thing is if you add up the cost of the parts in a lot of these preamps they are dirt cheap compared to the final product price, in other words a lot of the cost comes from the initial R&D but let's face it making that money back in most cases doesn't take very long and then they just go on selling it for exorbitant amounts of money and I feel in most of those cases they are making way more profit then most people would deem as Fair
@westinthewest3 жыл бұрын
@@MikeG-js1jt I'm confused about why preamps need to take R&D into account. Surely you can just implement a circuit which has already already been tried and tested twenty years ago. There are lots to choose from depending how fussy the client is. Why do we keep re-inventing the wheel?
@MikeG-js1jt3 жыл бұрын
@@westinthewest I'm sure there are scores of pre-amps out there that use "already developed" circuits, which brings us back to the original question "why are pre-amps so expensive" which leads us really to a single logical conclusion...GREED
@bobjegable3 жыл бұрын
I would like to know Paul's views on the ATC monitors behind him
@spiritspun48363 жыл бұрын
Can you explain the approaches used in modern low cost preamps such as Midas or Focusrite?
@Tibbon3 жыл бұрын
Thanks for this video! I've been wondering the same myself for a lot of ourboard gear. Especially for 500-series gear where I/O and power supplies are already taken care of... I'm just really unsure where the price comes in. Passives are cheap. PCBs are cheap these days. Transformers cost a bit, but not hundreds generally. Watching now to find out!
@timharig3 жыл бұрын
All that buffering he is taking about and all of those gain cells are not being done with passive components.
@ronaldarchibald25063 жыл бұрын
So could you just bi amp and only use preamp on the woofers thus getting clean precise highs and meaty deep lows.
@willie9537 Жыл бұрын
Paul, you're like the teacher on Welcome Back Carter I look forward to learning from you, like the characters in that show. When I see a new segment that song comes to mind. So, thanks Paul for the help and the smiles.
@Paulmcgowanpsaudio Жыл бұрын
Thanks! Never saw the show but I'll taker your word for it.
@willie9537 Жыл бұрын
@Paul McGowan, PS Audio Mr. Carter in the show had an easy way and an enjoyable experience. You are one of my favorite channels to check out after I pour my first cup of Joe. The best to you and your family.
@yshong373 жыл бұрын
Many thanks Paul
@johnt3643 жыл бұрын
What's the painting over your right shoulder? I like it!
@rapfreak77973 жыл бұрын
Pots also have a mismatch between the two signal levels due to a varied resistance between the two wiper paths. High end studio monitor controllers will typically use a relay network where each is connected to discrete resistors for repeatable volume levels and consistent stereo image.
@ranbymonkeys23843 жыл бұрын
Is there a same problem with electronic pots or volume controls?
@rapfreak77973 жыл бұрын
@@ranbymonkeys2384 pots are pots so they all have this issue. Some people think the problem goes away with stepped pots but they are still a mechanical device where a wiper touches a resistive plate; the steps just stop the wiper in predefined locations. These locations are not exact so the resistance will vary.
@ranbymonkeys23843 жыл бұрын
@@rapfreak7797 So if you have 1 pot per channel could you not match them? They may not show the same level on the knob but they can me matched I would think?
@ranbymonkeys23843 жыл бұрын
My NAD 2400 had 2 pots left and right I could adjust the little pots on the inside to make them match.
@rapfreak77973 жыл бұрын
@@ranbymonkeys2384 in theory yes but In practice no. Even resistors will have a tolerance level made to be a single value whereas a pot varies resistance based upon the location of the resistive plate; it’s a matter of physics.
@brkly993 жыл бұрын
I had been using a DAC with variable output direct to my power amp. I just upgraded to a pre-amp in between, sounds quite a bit better
@ford15463 жыл бұрын
all audio equipment has its own sound type and no one has the same sound! Compare with earphones straight out of the DAC. and straight out of the preamplifier and the sound should be equal. or straight out of CD player to straight out of preamplifier without DAC. and the sound shall be equal!
@bernard80293 жыл бұрын
I have the opposite experience; I go from my Dac (with volume contreol) straight to the amp; tried with 2 different tubed linestages and the sound was not better to worse than direct Dac-Amp.
@jeremyhughes64853 жыл бұрын
Well most DAC with variable output run at low signal level and can’t handle much capacitance load. It is not surprising that a good preamp will make a huge improvement. XLR and pro audio signal levels are the way to go if you want the finest in quality. Pro audio signal levels are higher than consumer level - more dynamic range or SNR.
@No_Limits_4113 жыл бұрын
Hallelujah! Been searching for this holy grail for some time now....
@soniksource3 жыл бұрын
thank you sir for this!!
@ReformedWhiteKnight3 жыл бұрын
That Studer 900 Series desk behind you has some very nice ... preamps! 🤓
@paymantavasoly32623 жыл бұрын
That Studer 900 series behind you is my dream console, I hope I can find one in a good condition someday
@Ultimate_Wasabi3 жыл бұрын
I'm curious what they are doing with the SSL Six sitting on the top of the cabinet on the right.
@paymantavasoly32623 жыл бұрын
@@Ultimate_Wasabi Routing stuff obviously, Besides I believe these guys make their own music sometimes, Man your eyes are even sharper than mine, Cheers 🤘🍻
@map400011 ай бұрын
Cool, good stuff
@new-knowledge80403 жыл бұрын
This is funny. For years I wondered how the input pots on my power amp would effect the performance, since a different setting give you a different impedance. The input pot setting for each side was slightly different on my power amp. So I was going to post a comment about that after watching the video. LOL
@RocknRollkat Жыл бұрын
Interesting explanation, thank you. Few people realize that every component adds 'color' to the signal, no matter how slight. And that coloration adds up................... Bill P.
@mkshffr49367 ай бұрын
The trick for the designer is to make that coloration the least objectionable as possible, which may or may not be the least "amount".
@RocknRollkat7 ай бұрын
@@mkshffr4936 ....hence the legend of that great preamp 'sound' ! This is a topic with no clear end in sight.
@carlitomelon46103 жыл бұрын
So, Paul Should my passive pre go before or after my tube buffer? (I have an old Musical Fidelity x-10d) I have a pair of power amps with a second input, I should try it out
@ranbymonkeys23843 жыл бұрын
I always liked the tube buffer just before the power amp, second to the last "thing" in the chain. Run it in line with everything else.
@derosa19893 жыл бұрын
the part that I struggle with is my system is only for 2 channel vinyl playback, and i don't need or want a bunch of source options i'll never use, and same with the phono stage, i'll never use the dozens of different cartridge loadings. Just want 1 reference level path for my TT
@riceman783 жыл бұрын
Thanks that was interesting
@user-js3op5lu7y3 жыл бұрын
T-Pad attenuator could be fixed the impedance of in and out? and why we don't control the volume on the source output?
@nntexperiences53643 жыл бұрын
Normally, the volume control in the source of dacs or cd players are not done properly. As you turn down the volume, you loose the detail and impact of the music. Some expensive dacs can do that without any problems, but most of dacs are not.
@ranbymonkeys23843 жыл бұрын
@@nntexperiences5364 How would one do it properly?
@ryanmelvey87643 жыл бұрын
i see you have the SSL six. love that thing!!!
@houssemguedria61012 жыл бұрын
i love the Studer Behind you
@jomgaard30353 жыл бұрын
Talking of preamps.. Do people have opinions of that Emm-Labs preamp down on the wire rack, bottom left of shot? I have one I bought for a home studio, tested it worked but never brought it out again! I'd love to know how it compares to high-end for hifi use. Mine is a Mk 1, all flip switches and couple of knobs.
@b.a.23353 жыл бұрын
Paul, this maybe a little off subject but relatable. Looking of using an AVR without pre-outs : Can the speaker output of an AVR without pre-outs be fitted with an rca connector (both positive and negative) from each front channel and used as pre-outs to connect to a power amp? If so, are there any consequences?
@b.a.23353 жыл бұрын
@Fat Rat okay. I was looking at it much like speaker line inputs into a plate amplifier of a subwoofer. Thinking the amp only needs the signal. If I may ask, what makes a separate power amp different?
@navy831ari3 жыл бұрын
Morning Paul, Are those ATC speakers, behind you?
@jamesplotkin46743 жыл бұрын
To add a bit of old-school tech and 1950's style sci-fi, hook up your turntable to a pair of Variac transformers.
@1970borntorun3 жыл бұрын
So you can get that "Brown Sound" like Eddie Van Halen? lol :)
@greggawhite3 жыл бұрын
Now I need pot. THANKS PAUL! :)
@FairyNL Жыл бұрын
I understand that in the analog world there are a lot of compromises to make and you need good quality materials. Recently I went from the Rotel RC1590 preamp (with a Minidsp AD-DA) stage between the speakers and subs) to a fully digital Minidsp Flex Balanced. Now the entire audio chain (until the output to the power amps) is digital. I noticed a very pleasant upgrade in sound quality, especially in the low end. At low volumes the bass frequencies are much more in balance than before, where at lower volumes it gets a bit flat. Isn't digital the best way to go nowadays? Digital sound (24/96) is absolutely fine, lots of headroom both in the dynamic as in the frequency department. You can pick the absolute original digital signal, process is to match the speakers/room/desired volume and at the very last stage convert it to analog and send it to the speakers? I do that now and I will never go back. This sounds very good to me and even the phantom center is now appearing to me, like the ochestra behind the speakers. I did not get that when using the analog preamp.
@Jvavolerpareil3 жыл бұрын
If I understood correctly, with a very loo impedance source, say 100 Ohms, I could use a relatively low impedance pot, let's say 1 k, and get close to performance of a buffer. Does it make sense?
@timharig3 жыл бұрын
A preamplifier's output impedance is typically less than 100 ohm. You are starting with an impedance of 100 and can only get higher based on the setting of your potentiometer. So no.
@menash41 Жыл бұрын
I have Roon. Should set the preamp volume to 100% and control the volume with Roon?
@amanieux Жыл бұрын
sorry about such a basic question : why do i even need a preamp ? is sound that bad when i just plug my dac output into the power amp ? i thought that any added element in the audio pipeline can only affect sound in bad way ?
@jimashby43 Жыл бұрын
I see the Gain Cell DAC is sold out. Are you going to make more of those? That would match well with the s300 right?
@TomAtkinson3 жыл бұрын
I'm gonna get riled up - I love it! Please explain a 1:1 impedance matching transformer please. :)
@timharig3 жыл бұрын
(n_p/n_s)^2 = z_p/z_s Where n_p is the number of turns in the primary and n_s the number of turns in the secondary. z_p is the impedance of the primary and z_s is the impedance of the secondary. A 1:1 transformer is an isolation transformer. It inductively transfers a signal at the same voltage and impedance from the primary side of the transformer to the secondary side of the transformer.
@milkman1000012 жыл бұрын
i remove my bhk pre the other day just to remember what the dac sounded like without it .and it defo sounded better with the pre installed.
@peterc31433 жыл бұрын
Very knowledgeable guy
@juicelord93213 жыл бұрын
Listen, OLD MAN... Do you produce BANGERS on that gear?!
@robertoj.fernandez21893 жыл бұрын
Maestro Thanks!!!!
@kemeremir Жыл бұрын
Hello Paul , with what amp are you driving your Atc speakers behind you ? Thanks
@Paulmcgowanpsaudio Жыл бұрын
Those are self powered ATC. I don't much like them but our mastering engineer, Gus, does.
@playbackvintagehifihunter96693 жыл бұрын
Hi Paul, where are you in this video? Obviously it's a studio, but those lovely ATCs jumped out right at me! Would love to know what you think of ATC speakers!
@eDXTRe3 жыл бұрын
My opinion on the ATC is; you don't buy them because of the great specifications. I think they have really flat frequency curve, but won't go really low, despite the big woofer and box housing.i guess The speakers are ATC SCM50A they go from 70 Hz-20khz within +/- 2dB -6db they will do 38Hz-20khz. I have heard them on a audio show in Holland. They played electrified from Boris blank. And I was not impressed at all.... So it seems those speakers are made for different purposes and use. And may be need a Subwoofer. I think they go loud and pretty linear specially for voices and instruments. But don't expect pants flappering bass when playing a contrabass or bass guitar. If a record is master on a pair of those speakers they will probably add bass to the master which will give a lot of bass in the home speaker setup. Or they might flatten the bass curve of the SCM50A using dsp I don't know.... I love the looks but the sound is not so appealing to me. Kind regards stefan
@playbackvintagehifihunter96693 жыл бұрын
@@eDXTRe hi thanks for your advice. Personally, I like tone and texture above deep bass. Midrange openess and detailed and lively highs. Do you think the bass from atc have texture?
@eDXTRe3 жыл бұрын
@@playbackvintagehifihunter9669 I think they have a kind of texture, but it's in the mid bass region. Regarding detail and texture in low bass my personal preference is dynaudio, the sound is detailed and uncompressed, if you go for passive speakers make sure the amp has plenty power 300 watt for a floor model is perfect and high damping factor, that will bring the dynaudio's alive. Recently I bought a pair of old dynaudio contour 1.1 speakers. Very small, but on a 200 watt amp they really sound amazing and go low also keeping texture. Regarding pro audio dynaudio also have studio monitors like www.dynaudio.com/professional-audio/core/core-59 And no I don't work or have affiliation with dynaudio, but I am addicted to the sound and the compressionless sound of it. Kind regards stefan
@SuperMcgenius3 жыл бұрын
Studio monitors are tools for the engineer, most professionals don’t change their monitors very often because they know their sound from album to album. That said they are good sounding speakers and it does not matter what Paul thinks of them.
@justinparkman35853 жыл бұрын
got the 11s wouldn't buy anything else get the right size atc for right size room that's the key for the Atc no subwoofer needed to killed what they can do .
@NiamorH3 жыл бұрын
well, what if the power amplifier also had a pot to adjust the input impedance, couldn't you just remove as much resistance that you introduce with the simple pot at the source?
@timharig3 жыл бұрын
Potentiometers always increase impedance. They never reduce it.
@michaelanderson37033 жыл бұрын
What speakers are those jus got my sb-2725 technics restored for 200$
@BijBijTCG3 жыл бұрын
ATC
@jeremyhughes64853 жыл бұрын
ATC SCM 50ASL
@No_Limits_4113 жыл бұрын
Btw, does this mean that preamp has the least impact on the sound when it's volume is maxed out?
@HenritheHorse3 жыл бұрын
The opposite
@timharig3 жыл бұрын
Assuming the volume control is simply a potentiometer, yes. However, the primary point of this video was to explain why he no longer makes volume controls where the volume control is simply a potentiometer. Once you replace the potentiometer with a gain cell, your statement is no longer true.
@HareDeLune3 жыл бұрын
Of course, my first thought when reading the title was Why limit this question to pre-amps? However, Paul has summed it up succinctly, with an answer that can be loosely applied in general to all components. Unfortunately. Another question might be, why is it now possible to achieve a great sounding system for a fraction of the previous cost?
@HareDeLune3 жыл бұрын
@Fat Rat 🤪
@H-773 жыл бұрын
The prices on really high performance op-amps have come down a lot too. With some of the offerings from TI (OPA1642 comes to mind) that ultra-low-distortion buffer has become a lot easier to implement.
@bear8myparents7343 жыл бұрын
I love what you do, Paul. You have a wealth of knowledge.
@H-773 жыл бұрын
I think Paul needs to get a whiteboard.
@codaalive50763 жыл бұрын
Very clean 2ch preamp (described as wire with gain) can be made with at most 150eur of material. Company THAT and some others sell dedicated ICs which are made to do this while sounding very well for what they are. Most high end preamps are about harmonic distortion they add, designers do search for clean sound but also carefully add coloration to it. People are paying too much for overcharges like marketing, shops, etc. Btw, huge companies like Behringer are buying known small companies with few employers to get even more $$$ than they have. Support designers and your pockets, buy directly from them.
@davep29453 жыл бұрын
There's almost always more than meets the eye in any product and high end pre-amps are no different. And ethe more esoteric the design the more issues have to be dealt with. All of that is true. However, there is another reason pre-amps can get so expensive and that is simply because they can be. A lot of people buying preamps are more dedicated music buffs and are willing to spend more money for better sound or at least the perception of better sound. Pre-amps are a must have when going to separate components and many an audiophile who goes that route will spend whatever they feel is needed to make their sonic dreams come true, within their budget, of course. Manufacturers know these people are willing to spend more so they can charge more. Same reason many integrated amps cost as much as they do. Yes, often the quality of a two thousand dollar integrated is better than that of an one thousand dollar AV receiver but very rarely is there a thousand dollars worth of aural difference. But someone who even knows what the difference between the two might be is someone that will spend the money for the slightest step up in audio quality and so they get the privileged of paying more. Not saying it's never worth it. Just saying that frequently when you are willing to step into more specialized areas of any hobby it's not always improved quality that makes items cost more.
@gordthor53513 жыл бұрын
Dave P Exactly. It's also a matter of the quantity sold (demand). A company like Parasound is in the middle of mass market and boutique companies, which I think this market gives people the best bang for the buck. There are better units from boutique companies, but one must pay a lot more for little gain.
@scottstrang15833 жыл бұрын
Didn’t the Modsquad have a passive preamp in the 80s?