QR2 Base-Side (Type-C) Video Guide

[@ChrisRaftis]

Not sure if my old clamp was tightened down way too tight or what, but while the old QR slid out of my base without a problem, I had to REALLY force the new one in there and yes, all of the slots were lined up properly.

[@PacoMarotoMP3]

Just happened the same to me. In my case the grooves weren't lined up perfectly with the usbc, so I had to try a few times with small increments in rotation until it went through.

[@NASCARJIMMAYFAN]

I think I broke mine

[@frankgordello]

I acquired the qr2 because of the disconnections with the qr1 lite and when placing the qr2 wheel side the shaft did not end up connecting to the USB C, after trying several times I tried to rotate the shaft and I was able to connect it correctly... someone else had this problem? I don't know if it is a problem with the USB C connection of my wheel base, which came inverted from the factory, or if the USB C connection of the QR2 base-side came inverted... luckily the software allows you to calibrate the steering wheel again to center it. At least what gives me a little peace is that the disconnections and movement between the qr wheel-side and the qr base-side stopped happening.

[@SevenEleven43]

Alles top, besten Dank für die Anleitung

[@Vortex001_MLG]

How do I know how much 8Nm is with the tool YOU provide?

[@acillatem1989]

Hello Fanatec team, when will you have in stock again QR1 aluminium wheel side? I'm on hold awaiting this to buy the v2.5. Thanks

[@ElRober97]

How can I make sure that I tighten it at 8nm…? I just ordered this and now I’m thinking about that

[@momorious]

Torque wrench.

[@chaddicusthegreat]

the allen wrench that is sent with it is a specific length and will torque to the approximate force required but as someone else mentioned using a small torque wrench, digital or analogue, is the better option to ensure you have the right clamping force.

[@ItzMav]

Thanks you gave me a csl dd with a qr1 base side that is stuck inside the base

[@hellsbells8979]

what is a difference between QR2 (type c) and QR (type c) Lite ? Thx

[@Invin_cibles]

limit of 8nm on lite and its carbon fibre infused plastic vs aluminium

[@SidVish]

A torque wrench is must for these things. Fanatec need to include something like in the kit. Ive just had to spend £50 on 1 as you cant guess. If you do try and guess, 'turn tight'. If you're having issues its most likely because you haven't tightened the bolts up enough.

[@zach.tempone]

You still need to tighten the clamp equally from both ends which a torque wrench wont help with. Including one really wouldn't solve anything.

[@SidVish]

@@zach.tempone I tightened mine both ends to 8nm with a torque wrench. I don't know what you're talking about here?

[@davidruizmartinez6198]

Hola una pregunta tengo una base CSL de pro compatible con PlayStation y me pregunta es si para el qr2 necesito el anclaje tipo c

[@bogumilpiotrowski]

I noticed an issue on your website yesterday. When attempting to purchase the GT DD PRO with QR2, I encountered the following message: 'This Wheel Base has a pre-installed QR1 Base-Side. You can upgrade this product to QR2 by selecting the QR2 Base-Side accessory below, which must be installed before use. (...)'. I'd like to clarify: if I opt to purchase the GT DD PRO with Base-Side QR2 , does this mean the WHEEL will also come with QR2? How the PS wheel is compatible with QR2?

[@Fanatec_Official]

Thanks for your feedback, Bogumil. We’re aware that this pop-up is not working correctly. Simply put: if you’d like the GT DD Pro to come with QR2, you’d have to separately add the QR2 Base-Side (Type-C) and a QR2 Wheel-Side for the steering wheel.

[@kongsnakekong5690]

Habra que esperar a que las bases vengan ya con qr2, al menos yo no pienso comprar nada hasta que no renueven ese aspecto.

[@ΈναςαπλόςΈλληνας]

@@Fanatec_Official if i purchase the base with qr2, why you dont instal it yourself and ship it ready? I mean you dont have to give the qr1 plus there will bee less problems to deal via people who cant instal it!

[@TehutiTheAlchemist]

I purchased the dd pro for PS5, would this be the same connection point on my wheel into the motor (USB-C)?

[@AmineMokhlisse]

Yes

[@davidruizmartinez6198]

Hola una pregunta la csld pro compatible con PlayStation necesitaría un qr2 y la conexión es tipo c gracias​@@AmineMokhlisse

[@Eifelfarmer2023]

Hallo frage ist das QR2 Base-Side (Type-C) kürzer als das QR1 Base-Side (Type-C) ???

[@Ruske85]

Can anyone confirm me this QR2 clamp is mate from METAL and is sturdier than the QR1 lite clamp? I'm having big problems with the plastic single bolt clamp, disconnecting my wheel approx every 1.5-2h of racing

[@Cookie747]

Had the same issue at high torque. Yes, the clamp that ships with the QR2 Base Side is made of metal and way better than the one that ships from factory with the csl dd. Although, the original qr1 clamp I got was also metal, just worked terribly.

[@cozmiixx]

there are 3rd party ones that apparently work well with the csl dd. i have ordered one and will try it out soon

[@Ruske85]

Thanks guys, fanatec sent me podium's clamp and till now it works well

[@cozmiixx]

@@Ruske85 decent. how tight did you do it up?

[@DINHO-tq8pg]

What's the difference between the QR1 and the QR2. I am planning of ordering a wheel the next week so i would like to know the differences in order to order it with the already pre-installed QR1 or order the QR2 as well

[@momorious]

You can find all Info on www.fanatec.com/qr2

[@peesicle]

​@grimreaper8038bit rude

[@Invin_cibles]

typical response from a socially inept v i rgin@grimreaper8038

[@Bordz_92]

Does this fix wheel wobble?

[@irlantiisti2810]

yes

[@Whoorms]

Does this fix the issue of internal usbc getting unplugged?

[@mj-np9sy]

Can you explain this? I know its the internal usbc connection but whats getting unplugged? A ribbon cable on the back?

[@Whoorms]

@@mj-np9sy so for the fanatec csl dd, from the dd base to the metal shaft, there is a connection. the way they decided to secure these two to each other was through plugging each other in with a usb c. the problem is that the clamp will over time, get loose due to vibration and high ffb. when it gets loose enough, the shaft to base connection unplugs, essentially creating an open, meaning that you wont be getting any force feedback.

[@origin9608]

@@Whoormsdid you buy the qr2 ? I have the same issue with qr1 and i wonder if the qr2 help to fix that.

[@Whoorms]

@@origin9608 qr2 did fix the issue.

[@origin9608]

@@Whoorms thanks for the reply

[@OffTheWall1320]

12 days since you guys sent me defective equipment, 10 days since i emailed Fanatec. No response yet.

[@willzjayvee]

how tight is 8nm?

[@willzjayvee]

use a drill with torque settings i guess

[@kylel534]

i litteratky can’t unscrew it this is so stupid it’s way too tight it’s litteratly breaking before loosening wtf fanatec

[@basicbins3751]

Same wtf

[@francescomurroni3599]

Guarda caso uscito il QR2 il QR1 è andato esaurito🤔 io devo acquistare il formula v2.5 e spero proprio che ci si insieme il QR1!

[@Fanatec_Official]

The QR1 is listed back in stock for the European market. Greetings, your Fanatec Team

[@francescomurroni3599]

ottimo 👍👍👍@@Fanatec_Official

[@jirkadolezal8127]

👍👍👍👍👍👍👍👍👍👍👍👍

[@forzaferrari438]

Scusate, ma a cosa dovrebbe servirmi fare questo?

[@GUS-B069]

Arreglad vuestro sofware primero!!!!!! Os comen el mercado el resto de nuevas marcas!!!!

[@oldy_7651]

Kümmert euch lieber um alle anderen bestellen !!!

[@The_Mup]

⚠️ *Give me my order or give me back my money!* ⚠️

[@louaiempire8943]

I know man I have been into a lot too they used to take a month to deliver my orders

[@MaxHasManyHobbies]

They're on backorder as stated on the website. It took a few weeks before mine was shipped, but it's coming. Don't worry.

[@louaiempire8943]

@@MaxHasManyHobbies now they delivering orders quicker I'm recovering mine in two weeks at the maximum I think they learned their lesson

[@EM_Karting]

@The_Mup you're actually sad for spamming the same comment on multiple videos

[@EM_Karting]

​@@MaxHasManyHobbiesI somehow got mine within a week and half of ordering

[@neilbradley6571]

Why isn't this a recall part for free? Instead you will charge me 200 dollars so my 800 dollar wheel wont fall off!!!!! Thieves!!!!

[@VQS_Risky]

I highly agree with you. There should have been a solid discount for this part for people like us. my dd pro is 6 months old and i couldnt even write them a repair order. i cant believe im trying to solve issues by spending another $200. regardless of what i did my wheel would disconnect. Pretty upset about this issue.

[@mohbw3]

Max max max Super Max

[@kubagrundszok]

Dududududu max verstapen

[@Eirik.paulsen_33.]

@@kubagrundszok dududud Max verstappen dudududu next guy keep it going