How To Wire Subwoofers - Parallel vs Series - Single Voice Coil and Dual Voice Coil

  Рет қаралды 1,296,164

Quality Mobile Video

Quality Mobile Video

Күн бұрын

Пікірлер: 935
@sonusancti
@sonusancti Жыл бұрын
Good video. You ought to also mention how series or parallel connection impacts the total power handling capability which also impacts amp selection.
@humandr2873
@humandr2873 2 жыл бұрын
Hi, A little help please. what would be the best subs to get the most rms power out of my MTX D81000 amplifier?
@4twny
@4twny 8 ай бұрын
😊0
@JohnBlaze-ow5tp
@JohnBlaze-ow5tp 5 жыл бұрын
I think I know less now than I did before I watched this video.
@vinayt7897
@vinayt7897 4 жыл бұрын
True.....hahahahaa.😂😂😂
@jeremypolanco7377
@jeremypolanco7377 2 жыл бұрын
Lmfaoooooo
@drkool8168
@drkool8168 2 жыл бұрын
Bro, for real, alot of it was technical and a few parts were overcomplicated. That said, I did learn alot and am very grateful for this video.
@JohnBlaze-ow5tp
@JohnBlaze-ow5tp 2 жыл бұрын
@@drkool8168True, I got the general got it too but he definitely pit a lot of technical detail into it 😆😆
@BigDaddyGamingFTW
@BigDaddyGamingFTW 2 жыл бұрын
I knew how to wire up an amp and subs and everything, only thing i didnt know was how to wire up a head unit. Now after seeing this, i might accidentally switch my power and ground with each other
@gabriellarouche3702
@gabriellarouche3702 2 жыл бұрын
Hey thank for the helpful video, but one question i got two 6.75 dual voice coil and a kicker CX360.4 how do i wiring my sub into my amp. Do i wiring bot sub in bridge or 1 on each chanel cause in your video it seam always plug in one chanel and I want wiring two coaxial 4omh speaker Thank you for the help.
@Qualitymobilevideo
@Qualitymobilevideo 2 жыл бұрын
What impedance are your 6.75 subs?
@gabriellarouche3702
@gabriellarouche3702 2 жыл бұрын
4 ohm
@ICP1SBJ
@ICP1SBJ 6 жыл бұрын
great info! I was into car audio in 90's. I ran four 15" subs in their own ported boxes and ran them series/parallel to get a 4 ohm load and powered the fosgate subs with 2 fosgate power 250 M's bridged together to give me over 1,200 w at a 4 ohm load. I hit 147.3 dbs once and thought that was great for 1996. Wanting to get back into it so i'm checking youtube.
@johnd5542
@johnd5542 2 жыл бұрын
Lol. That would be a st8 banger back in the day. But todays standards........
@jseldevillagran2752
@jseldevillagran2752 2 жыл бұрын
What about wiring them vertically instead of parallel?
@lloydhudson6463
@lloydhudson6463 10 ай бұрын
Considering that's just two subs, that's still damn good, even today.
@ICP1SBJ
@ICP1SBJ 10 ай бұрын
@@lloydhudson6463 "four 15" subs" but yeah it was the loudest stereo in my town at the time
@adrianalvarez6009
@adrianalvarez6009 4 жыл бұрын
Quick question What's better 2 JL audio 12TW1-2 shallow subs (2ohm subs) running on a JL audio JX 500/1 Or 2 JL audio 12TW1-4 shallow subs (4ohm subs) Running on same amp??
@RobVaughan1984
@RobVaughan1984 4 жыл бұрын
2ohm louder
@sebastiandiaz29
@sebastiandiaz29 6 жыл бұрын
For calculating the impedance in parallel you don´t need that formula, just divide each speaker´s impedance by the number of speakers, so if we have 4 speakers each at 8 ohms, just divide 8/4= 2
@coltonnewman8283
@coltonnewman8283 6 жыл бұрын
Sebastián Díaz that’s exactly what I’ve always done! If I wire two 4 ohm dvc subs in parallel I get an1ohm load. It always get me why this confuses some people so much you just gotta take a little time and thoughtfully plan out a system
@caidenbilliot8768
@caidenbilliot8768 3 жыл бұрын
Yup, over complicating impedance is the reason why most people don’t learn how to wire subs.
@jenn1022
@jenn1022 2 жыл бұрын
@@coltonnewman8283 wouldn't that be 2?
@tobiasmenough
@tobiasmenough 2 жыл бұрын
@@jenn1022 yeah.. but thats 2 ohms per sub. Then ya parallel the 2 -2 ohm sub loads for a 1 ohm load.
@jenn1022
@jenn1022 2 жыл бұрын
@@tobiasmenough He say he paralleled (2) 4 ohm speakers. 4÷2=2. That's a 2 ohm load. What turns it into 1?
@taylorbeckett7733
@taylorbeckett7733 2 жыл бұрын
When using active powered subs at home how do perform series/parallel wiring with high level outputs
@Qualitymobilevideo
@Qualitymobilevideo 2 жыл бұрын
When using active you cannot, the amp is in the sub, regardless of home or car.
@WilliamBasley
@WilliamBasley 7 жыл бұрын
Pretty sure that's the first time I've heard Ohm's Law equated to getting drunk, lol!
@Qualitymobilevideo
@Qualitymobilevideo 7 жыл бұрын
😂😂😂
@denshi-oji494
@denshi-oji494 5 жыл бұрын
Obviously he was drunk when he made the water diagram.
@EBMproductions1
@EBMproductions1 4 жыл бұрын
Can anybody tell me how i should wire multiple DVC subs to a Two channel Pro Audio amp?
@lacyfurmage8846
@lacyfurmage8846 3 жыл бұрын
?? How would it work and sound if you took a good 12" home speaker and cut it in 1/2 removing the tweeter and mid range stuff and just left the big speaker end of it, then covered the "CUT" end area back over and hooked an amp to it??
@RustyCarnahan
@RustyCarnahan 7 жыл бұрын
Your water analogy is flawed. Voltage::pressure Impedance::restriction in the line Amperage::flow through the line
@davesdailyYT
@davesdailyYT 6 жыл бұрын
RustyCarnahan Yes. And thank you. Was wondering if anyone else caught that
@muddyfunker3014
@muddyfunker3014 6 жыл бұрын
I noticed this too, these are very good well explained videos but you're right. Voltage is pressure.
@Thumper68
@Thumper68 5 жыл бұрын
Electricity flows like water the path of least resistance. So a Water analogy is correct just not his lmao!
@bassdrumflextime1253
@bassdrumflextime1253 5 жыл бұрын
Yup
@WhereAmEye2187
@WhereAmEye2187 4 жыл бұрын
Well, amps measure current so that makes sense
@changingoftheguard7256
@changingoftheguard7256 2 жыл бұрын
What about a triple coil sub like the 12 Infinity kappa 120.9 it's got a built-in SSI.
@Qualitymobilevideo
@Qualitymobilevideo 2 жыл бұрын
Haven't tried one of those.
@ParosPasxaRide
@ParosPasxaRide 7 жыл бұрын
u can say the exact same things much simpler but i guess you do it so people click on your site, also bulbs in series.... if 1 blows up ALL will shut off not only after the bulb that blew up
@kevinfairclough4619
@kevinfairclough4619 6 жыл бұрын
ParosPasxaRide nn
@braceyourselvesfortruth2492
@braceyourselvesfortruth2492 4 жыл бұрын
Can't believe I missed that, but you're absolutely right. In an already extremely confusing video for beginners, the animation there and his explanation was highly inaccurate.
@handson3223
@handson3223 5 жыл бұрын
can you do a video for mids and highs? it seems like nobody does a video for this one
@Lifeizrigged
@Lifeizrigged 4 жыл бұрын
3 years ago and still saving lives😂
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
LOLOL
@jerryodell9955
@jerryodell9955 4 жыл бұрын
@@Qualitymobilevideo òòò oò
@jimmyallen754
@jimmyallen754 4 жыл бұрын
very good when it will pick up at all.good ,and clear.
@John-rk7lh
@John-rk7lh Жыл бұрын
Very cool. But what is the formula when using a series parallel wiring?
@SonicElectronix
@SonicElectronix 7 жыл бұрын
I enjoyed the comparison of Ohm's law to drinking!!!
@Qualitymobilevideo
@Qualitymobilevideo 7 жыл бұрын
Lol thanks!
@jnowski9622
@jnowski9622 7 жыл бұрын
Yeah... just too bad they fuked up on the diagram for the water/electricity analogy right before that though... 0:55 ✗ *Voltage = Pressure* ✓ Current = Flow ✗ *Resistance = Pipe Size*
@Qualitymobilevideo
@Qualitymobilevideo 7 жыл бұрын
Negative, rethink what you just wrote. Its the very reason municipalities use high voltage on long runs and use transformers to lower the voltage in an effort to reduce wire costs. You trade one for the other. Think commercial distributed audio.
@ckimsey77
@ckimsey77 7 жыл бұрын
Negative twice, high voltage lines over distance definitely has an advantage and reason, but that has nothing to do with the water analogy in question (which is wrong). Long travels have high voltage so a low current flows to deliver the power (P=IV), low V trying to supply a small town would require ridiculously high current which would melt the wires. You raise V to lower I while delivering the same power, drastically increasing efficiency as well as its not possible at low values of V. Nice way to dance around a question with a random, unrelated comment. V is the pressure, i.e. the driving force, that pushes charges along a conductor. The very definition of Voltage relates it to an electric field, which is a vector FORCE exerted on charged species; in this case negatively charged electrons. If V is a force, moreover the driving force, then how can it be represented by the pipe size? The driving force of water is pressure obviously, which relates to electric driving force defined as voltage. Pipe size only exhibits a resistive force, it resists flow. The very words "resists flow" in the description says it all: pipe size relates to resistors. Lastly, if pressure related to resistance then explain this. What happens to flow when pressure decreases? The flow also decreases. If a force is reduced then the body being driven by the force slows and also decreases. What happens to current when resistance decreases? It INCREASES current by decreasing resistance; thus R cannot be the pressure. By definition, resistance opposes movement, not causes it. Thats like saying applying more brakes in your car (increasing "resistance" related as driving force "pressure") will increase speed (flow); brakes are the car system's resistance, so if resistance is analogous to the pressure driving the system then increasing brake would increase speed. Bottom line, electric R is nano-scale friction, where the flow of electrons are inhibited by colliding with atoms and repulsive forces pushing them away from desired direction of flow, causing energy loss as heat. Friction/resistance in no way can be represented by pressure; one causes energy loss and resists work and movement where the other stores energy and causes work or movement.
@EBMproductions1
@EBMproductions1 4 жыл бұрын
Can anybody tell me how i should wire multiple DVC subs to a Two channel Pro Audio amp?
@victorponce7238
@victorponce7238 Жыл бұрын
Yes I am connecting my woofers today. Your video answered my questions. I have dual voice coil 4 ohm. I am going with parellel
@Qualitymobilevideo
@Qualitymobilevideo Жыл бұрын
Bump it.
@victorponce7238
@victorponce7238 Жыл бұрын
@@Qualitymobilevideo ok. My system is bumping HARD! However I am using a 2000 watt NEMESIS amp and the stupid thing gets hot after 20--30 min of loud bassing and it turns off.........talk about losing an erection. Ah ha guess I need a better quality amp. Looks like. Any recommendations?
@adangarcia6584
@adangarcia6584 2 ай бұрын
Get a cooling fan. I bought a specific amp that ran in mono, pullimg all 800 watts. The amp had a special circuit that ran cool and would shut off if the temperature spiked. It was shutting off all the time. Went to radio shack and bought a couple of 12dc computer fans, built little fixtures for them to attach to the amp, and presto, no more shut downs. If your amp does not have that cooking circuitry, you will end up, over some small spance of time, burn up your amp. Man, you could hear my one 8in dual voice coil from down the street. People thought I had a couple of 12s in there. I miss that life. Now I drive a 2018 Volkswagen Tiguan and I wouldn't know how to get into that dashboard to install the wires and harness adapters.
@Silentjustin06
@Silentjustin06 5 жыл бұрын
This is a very detailed explanation but confusing for people. Its way more simple to just double the ohm in series wiring and cut the ohms in half in parallel wiring
@johnnypena1083
@johnnypena1083 3 жыл бұрын
How can you connect both and keep a 4ohm load ?
@joezupko
@joezupko 6 жыл бұрын
learning this in my physics class now, subwoofers are way more interesting though haha
@patrickvictorino9779
@patrickvictorino9779 2 жыл бұрын
So if you make 2ohm dual voice coil 4ohm will that damage the sub?
@Qualitymobilevideo
@Qualitymobilevideo 2 жыл бұрын
Absolutely not
@best1yet
@best1yet 7 жыл бұрын
you lost me with the equations
@VictorEstrada
@VictorEstrada 5 жыл бұрын
in other words: parallel wiring = less ohms (more power out of amp, but stable if within amp specs), and series wiring = more ohms (less power out of amp, but more stable)
@denshi-oji494
@denshi-oji494 5 жыл бұрын
@@VictorEstrada Yes mostly. There is another factor to consider however, that is the damping rating of the amp. Good luck finding it, as nobody rates them that way now. It is a measurement of how stable the output on the amplifier is with varying load, (which all speakers do vary in impedance with frequency, the enclosure type and size, and even temperature!). Anyway, speakers in series also have the general ability to effect each other more than speakers in parallel. So, unless the speakers are installed exactly the same, with no differences in external influences, the speakers wired in parallel will more closely match each other in motion and sound than those wired in series. And an amplifier with a higher damping factor will also be better able to prevent excessive cone excursions at higher power.
@michaeltempsch5282
@michaeltempsch5282 5 жыл бұрын
@_ David _ if (and if not the setup is rather odd) all the coils are the same impedance then you can simply divide by the number of coils. 4x 4 Ohm coils in parallel makes 4/4 = 1 Ohm final load
@charlesd.morgan362
@charlesd.morgan362 5 жыл бұрын
I have 2 8ohm speakers, that would total 16 ohms in series correct?
@michaeltempsch5282
@michaeltempsch5282 5 жыл бұрын
@@charlesd.morgan362 yes - series is calculated by simple addition.
@marklindley8408
@marklindley8408 3 жыл бұрын
How about the old school Memphis madd maxx 15 inch quad 1 ohm subwoofer? You have in a single sub 4 coils at 1 ohm does that make .25 ohm and 4 ohm respectively. Can you get the sub to do 2 ohm load to amps by splitting the loads to two coils per amp? Effectively making .5 ohm and 1 ohm or is it .5 and 2 ohm? I am thinking.5 and 2 but keeping it at 4 coils in one sub to a single amp make it .25 and 4 I believe. How about that brain teaser. I do believe it makes a .25 and 4 ohm load but also can you just put 1 amp per coil then keep the resistance at 1 ohm and that’s basically it?
@Qualitymobilevideo
@Qualitymobilevideo 3 жыл бұрын
it’s actually .25 and 1 ohm.
@QuietWind01
@QuietWind01 6 жыл бұрын
Also, for people who don't understand, at 4:25, you label them as A+, A-, and B+ and B-. On an amplifier, most of the time, the power (that goes from the battery (or the alternator, for higher end systems) terminal is labeled as B+ and for people who don't really have any experience, I can see people wiring up their pos+ on their battery to the "B+" you stated on the terminal on the speaker... would have been better off labeling them 1 and 2
@oneofthosepeople2101
@oneofthosepeople2101 7 ай бұрын
I have a receiver with the capability to run 4 speakers and I only have one speaker in the car. Old Bronco. Can I combine speaker wires to get more power to one speaker?
@SoundstreamTVNetwork
@SoundstreamTVNetwork 4 жыл бұрын
Some of you didn't watch this whole video, and it shows....
@christopherwise7067
@christopherwise7067 4 жыл бұрын
i watched this whole video, it made me feel stupid. i went to a more reliable source to get smarter again, the electronics section of my automotive technology text book. for a text book, it made a hell of a lot more sense then this video. i even had to rewatch the wiring diagrams he used to make sure they were correct.
@QuietWind01
@QuietWind01 6 жыл бұрын
There are simpler ways you could have explained this, you didn't necessarily explain it wrong, but there are going to be people out there who aren't as experienced as some of us, and might get very confused.
@franciscomercedesdelossant7564
@franciscomercedesdelossant7564 3 жыл бұрын
Greetings, I want to install pioneer sea-835 tab in kia sorento sx 14 is the most complete integration system should I use to maintain the functions of the guide and navigation ???
@sam6stringestrada31
@sam6stringestrada31 7 жыл бұрын
We clicked on this video for info......... after this video I'm overloaded
@Up2Trbl
@Up2Trbl 6 ай бұрын
For anyone who comes across this video today. He made things WAY more complicated than necessary. For series wiring your final ohm load is (ohm of the voice coil) x (# of voice coils) For parallel wiring your final ohm load is (ohm of the voice coil) ÷ (# of voice coils) For example, you have 2 DVC 4-ohm subs. That's 2 subs with 2 coils each, and each coil is 4-ohm. So series would be 4-ohm x 4 VCs = 16-ohm And for parallel it'd be 4-ohm ÷ 4 VCs = 1-ohm For Series/Parallel which he commented on for just a second, it's a "little" more complicated but you just calculate the series connections first and then treat each series connection as a single voice coil of it's calculated impedance and calculate the parallel connections ohms based on that. I'm not great at explaining things, but hopefully that makes sense. So 2 DVC 4-ohm subs, both voice coils on each sub are wired in series and then the subs are wired parallel to each other. So you calculate the total impedance of each sub separately (2 4-ohm VCs wired in series so 4-ohm x 2 VCs = 8-ohm). Then imagine each sub as a SVC 8-ohm sub and think if you wired them in parallel (8-ohm ÷ 2 VCs = 4-ohm). So 2 DVC 4-ohm subs wired in Series/Parallel would come out to 4-ohm at the amp.
@GodsTowhead
@GodsTowhead 9 ай бұрын
What if one of the subs is a dual voice coil and one is a single voice coil? Because thats what i have. What is the optimal way to hook them up?
@BenBlackEquinoxEngelhard
@BenBlackEquinoxEngelhard 6 жыл бұрын
The wizard was all I needed, thank you!
@Qualitymobilevideo
@Qualitymobilevideo 6 жыл бұрын
😉
@gideonpeprah
@gideonpeprah 3 жыл бұрын
Hahahaha 😂 me too
@mattparks11
@mattparks11 4 жыл бұрын
i have 2 skar vd12 i’m pretty sure it’s a single voice cool but it has 2 pairs of positive and negative hookups ?
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
It's a telling sign when there's a D in the part name that it's DVC, and the fact that there are two pairs of negative and positive terminals, mean they're most likely DVC
@mattparks11
@mattparks11 4 жыл бұрын
Quality Mobile Video ok cool. thanks for the help
@Ninjasraynonu3
@Ninjasraynonu3 7 жыл бұрын
Also when you strap amps the impedance( ohms) are brought down which provides more bass. My sub is currently wired to .5 ohms which is kind of risky but I love it on my two Orion 12's.
@kingkongboy07
@kingkongboy07 2 жыл бұрын
I got 2 Rockford P2d210 (old school model) in 2 separate boxes running with an Alpine Pdx-M6, how should I wire them subs?
@fidazaman3155
@fidazaman3155 6 жыл бұрын
My head is hurting.. and I just subscribed just now.
@ramonhernandez3812
@ramonhernandez3812 6 жыл бұрын
After viewing this video, I had to subscribe. Nice vid bro, get down to the point with no BS
@Qualitymobilevideo
@Qualitymobilevideo 6 жыл бұрын
Thanks bro!
@charlesshifflett2989
@charlesshifflett2989 2 жыл бұрын
I have 2 10" Rockford p2 4ohm speaker and Rockford r2-750x1 amp what is the best way to wire the speakers to the amp? Series or parallel? And what is the best ohm to have at the amp?
@odenfilms7850
@odenfilms7850 6 жыл бұрын
I started to get sleepy when the math problems started lol
@jamingjohnson2275
@jamingjohnson2275 4 жыл бұрын
Sleepy? You stayed around that long? I couldn't do it.
@cacavman
@cacavman 7 жыл бұрын
So if you have 3 subs at 3ohms impedance what do you run it at the amp 1, 2, or 4 ohms.
@marathondude
@marathondude 7 жыл бұрын
Those overfocused on power/watts should not neglect how important RMS is, plus the need for headroom to avoid clipping.
@Catholic1391
@Catholic1391 4 жыл бұрын
Ok I have two Skar ZVX v2 d2 12 dual 2 ohm, how will I bring both down to 1 ohm at the amp, my guess is don't hook up the other end on the same subwoofer but hook up the two subwoofers together. So it will be 1 ohm. Is this correct? Thanks for info
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
Can't. Two DVC 2 ohm woofers cannot be wired to 1 ohm. Only 2 ohm or 8 ohm :(
@mikeb611
@mikeb611 7 жыл бұрын
🤔🤔🤔🤔🤔😑😑😑😑😴😴😴😴 . Hope there's no quiz.
@robysvids
@robysvids 3 жыл бұрын
I got a 1500watt dual voice coil boss 4 ohm and a 800watt boss single ohm speaker 4ohm. My guess is half the watts is actual rms. I'm not sure what amp to get and whether or not to do parallel for 2ohm or series for 8 oh 🤔 confusing. Perhaps someone can help me find a amp.
@Qualitymobilevideo
@Qualitymobilevideo 3 жыл бұрын
You cannot use both subwoofers together on the same amp or in the same box. You will need separate amplifiers and enclosures and set the outputs individually.
@robysvids
@robysvids 3 жыл бұрын
@@Qualitymobilevideo makes sense ty! I'll get another of the same.
@Rsthelen
@Rsthelen 7 жыл бұрын
And they told me there would be no math installing my subwoofer!
@Qualitymobilevideo
@Qualitymobilevideo 7 жыл бұрын
HA!
@handsofsteal8152
@handsofsteal8152 6 жыл бұрын
Rob St.Helen lmao
@douglasspurgeon24
@douglasspurgeon24 6 жыл бұрын
Lol
@timoromeo7663
@timoromeo7663 5 жыл бұрын
Rob St.Helen News flash: there is math in everything you do, even pooping.
@christopherwise7067
@christopherwise7067 4 жыл бұрын
there is no math if you just use a multi meter and have a basic understanding of wiring speakers.
@barrylong6507
@barrylong6507 2 жыл бұрын
Okay I have a the setup that is single voice coil wired in parallel making it a. 2omh 1000rms set up so can I use a 2 Channel 4omh per Channel 500 RMS pre channel amplifier as well as a mono 2omh 1000 amp
@bigstunner1381
@bigstunner1381 5 жыл бұрын
I come back to this video every so Often now that I know how to wire subs , and all I have to say is you made this a lot more confusing than it had to be
@braceyourselvesfortruth2492
@braceyourselvesfortruth2492 4 жыл бұрын
He really did. Moved way too fast for people who don't know Ohm's Law at all. I just graduated with a BS in electrical engineering and was a supplemental instruction leader for Physics - Electromagnetism and Waves, which I aced as a student. I also do all my own car stereo work. Even with all that, I was barely able to follow it.
@OpAfAnx
@OpAfAnx 4 жыл бұрын
So I’ve got 2 4 ohm dual voice coil speakers if I wired them in parallel what would my final impedance be?
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
It will be 1 ohm! We actually have a video on this: kzbin.info/www/bejne/nKrcdnekq5KHbdE
@OpAfAnx
@OpAfAnx 4 жыл бұрын
Quality Mobile Video if I series parallel wire then my final impedance should be 4 correct ?
@yesno8204
@yesno8204 7 жыл бұрын
You clearly dont know what a how to is... Its like theory vs experience - the one explains how its done and the other show how its done...
@YiZuSc
@YiZuSc Жыл бұрын
Any issues if mixing single and dual voice sub's in a box?
@Hammer4400
@Hammer4400 7 жыл бұрын
You could also use this equation to parallel wiring, I think It's a bit easier. ((r1^-1)+(r2^-1)+(r3^-1)+..ect.)^-1 so your example would be: ((R1^-1)+(R2^-1))^-1 = ((4^-1)+(4^-1))^-1 = 2 ohm's
@shonrob1620
@shonrob1620 7 жыл бұрын
Emil Hammer this is the reciprical formula
@SirDella
@SirDella 7 жыл бұрын
(R1xR2):(R1+R2) is the best one
@MegaPain619
@MegaPain619 5 жыл бұрын
I। have kicker comp d 15" dvc. So tell me that wether it should be wired in series or parallel to get good base?
@lapamatogeiming3030
@lapamatogeiming3030 5 жыл бұрын
it depends of your amplifier. for example i'm buying 10" 1500Wrms subwoofer with 2x1ohm voice coils and an amplifier that is 3050Wrms at 1 ohm (im buying other subwoofer later) the amplifier specs tell me that its 1550Wrms at 2 ohm load -> i connect my voicecoils to series to get 1+1=2ohm and now my amplifier isnt overloading my woofer. but if i bought 3000wrms subwoofer with 2x2ohm voicecoils with same amp, I would connect voicecoils parallel to get 1ohm impendance and match it with my amps 3050Wrms at 1ohm (2x1 ohm voicecoils wouldn't work because i only could put it parallel to get 0.5ohm and overload, or put it to series and get 2ohm and not have enough power.) So basically you need to look at your voicecoils and wattage and then match it with an amplifier.
@Safar1967
@Safar1967 6 жыл бұрын
@1:6 He uses a nice example on alcohol ....LOL. its an appropriate example too. vomiting is example of power out....double lol
@JamesDeveneyProductions
@JamesDeveneyProductions 5 жыл бұрын
Lol
@imhavnillusions
@imhavnillusions 6 жыл бұрын
I feel like we can make this into a drinking game!
@DonChubz
@DonChubz Жыл бұрын
hey when you use the formula to get the min-max wattage amp to match the sub is it okay to go a little over the max ? for an example if 2 subs =2500 rms the max wattage with the formula is 3000 watts. Is 3200watts okay to run ? How about 4k on it ? how about 3000rms= 3600 max watts from amp Is 4k safe to run ? how about 5k ? THANKS
@DonChubz
@DonChubz Жыл бұрын
also 2 dual 2 ohm subs wires to 1 ohm 2500rms if I get a 1 ohm 5k amp can i wire it to the subs at 2 ohms 3200 watts ?
@fallofthezombies1379
@fallofthezombies1379 5 жыл бұрын
He said load
@sushi8204
@sushi8204 Жыл бұрын
Maybe you can answer this. I want to replace the sub in my new RAV4 Prime with JBL. Already replaced all the speakers in the doors and on the dash. I am using factory amp because it is not so bad. The OEM speakers are bad though. I want to replace the sub because it is made out of paper, has very small magnet and produces a lot of distortion and booming. I want a tight sound but not necessary low. I was told that I have to wire my existing factory amp to a dual coil sub with no more than 75w RMS or wire it so it is 8ohm. The reason for it is so I would not blow the factory amp. Is that true? Thank you.
@chadtarleton3413
@chadtarleton3413 7 жыл бұрын
Good video. Very informative
@FlyingDurag
@FlyingDurag 3 жыл бұрын
So with the series wiring, should I be using a negative wire to connect sub a to sub b? I have the single coil
@fattonykauaihaun7577
@fattonykauaihaun7577 6 жыл бұрын
He's making this over complicated so u go to his shop. And pay him to hook up 2 dvc12s to amp and a capacitor 🤣
@RealRoCKoFF
@RealRoCKoFF 6 жыл бұрын
He is it's better whatch ones that show u hands on this dude just speed thru it
@mikecheeze4312
@mikecheeze4312 5 жыл бұрын
Capacitors are worthless and can damage your amp. If you need one get an h/o alternator and/or second battery. Let's say you have a long bass note like in EDM music. The first second will most likely drain your caps "load" but your battery cant fill it fast enough as you amplifier is asking for. Therefore cause under voltage and possibly damaging amp. Caps are worthless...they're a gimmick. Also big 3 upgrade is good idea 👌
@timoromeo7663
@timoromeo7663 5 жыл бұрын
FAT TONY KAUAI Haun What does a capacitor have to do with this?
@jacobwebb8818
@jacobwebb8818 4 жыл бұрын
@@timoromeo7663 he's saying he's gonna hook you up with a cheap simple system
@domls1317
@domls1317 4 жыл бұрын
You did series wiring when showing parallel at 4:41. You have the positive wire going to B+ when you had just showed it going to A+ with the single speaker.
@BlastManX20
@BlastManX20 6 жыл бұрын
My head hurts now
@pyrozmechanicvividcustomsl575
@pyrozmechanicvividcustomsl575 5 жыл бұрын
He complicated the fuck out of audio so badly
@christopherwise7067
@christopherwise7067 4 жыл бұрын
mine did to, so i pulled out my automotive text book to clear myself up
@marnameee7961
@marnameee7961 5 жыл бұрын
Denon AVR-3801 AM/FM Stereo 735-Watt 7.1-Channel Home Audio Surround Receiver - sub woofer has a pre out right and left. the 2 subs i want to hookup has only one right left in on each sub. how to i hook them both up without loosing any power from each.? i did hook with a splitter one wire/ cord to each but lost power or sound to each too. do i need multiple kinds of splitters for this? thanks for any info? or help...i had pics but don't see where to add them? hmm.. but any help would be great! Thanks..
@henrycagle7827
@henrycagle7827 5 жыл бұрын
series you add parallel you divide by 2 on total value. 😄
@mikecheeze4312
@mikecheeze4312 5 жыл бұрын
Unless you have more than 2 in parallel... then you keep adding to the division
@christopherwise7067
@christopherwise7067 4 жыл бұрын
it is slightly more complicated then that. if you have two speakers, it might be that simple but add another speaker there at 4ohm now you have 4+4+4=12 12\3 is still 4. check my other comment for specifics
@Torpengpogi
@Torpengpogi 5 жыл бұрын
well, series wiring a dual sub is not ideal, bec. they will add the frequency resonance also, but i have one question for you, is it ok to wire a dual vc sub using 2 separate amp for each voice coil, one voice coil from one amp, then the other voice coil from another amp? thanks.
@AntDaddy1977
@AntDaddy1977 5 жыл бұрын
they would have to be setup exactly the same and you would need a way to measure that because no two amps are gonna be exactly the same even if they both brand new. You would need a ocilscope and other audio testing equipment that most people dont have.
@fredbradshaw3129
@fredbradshaw3129 4 жыл бұрын
They would have to be gain matched but yes yo can. The amps volts and clipping point. Cannot do it by hand, you need a luimy, a dd-1, or a scope to gain match. If your amps are strappable, you can strapp and wire up, series, or wire down, parrallel, depending on your subs and amps impedence, wire accordingly.
@slantedskill5742
@slantedskill5742 6 жыл бұрын
Omg thank u so much i switched to parallel and my kicker comp vr are booming with a ssl evo 1000 watt amp with a pc power supply. IM ONLY 13 years old
@preformancemustang
@preformancemustang 5 жыл бұрын
I get the speaker wiring but what about the amp. So lets say 2 channel amp. Two dvc 4ohm. Would you wire each speaker to the own channel or bridge them??
@Qualitymobilevideo
@Qualitymobilevideo 5 жыл бұрын
A 2 channel amp you would just wire each subwoofer to their own channel. Bridging comes into effect with a monoblock where you bridge two subs onto one channel, or a 4 channel/5 channel where you bridge each subwoofer to two channels.
@jmaslin
@jmaslin 7 жыл бұрын
I thought Viagra fixed Impedance...... what, what?!
@timstaples3450
@timstaples3450 4 жыл бұрын
Wait so I have two 12inch SVC 4 Ohms subs. What amp would I need and how do i need to wire it?? From what I got.... I believe a (Stetsom EX3000 2 ohm Amplifier Car Audio Mono Amplifier Digital Amp Sound 3600 W) would work right? and I am supposed to wire it in parallel?
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
You'll be making a 2 ohm load in parallel yes. But I can't recommend an amplifier without knowing the power specs of the subwoofers
@brady9169
@brady9169 6 жыл бұрын
Quality videos man. Big help
@rickeysneed3855
@rickeysneed3855 4 жыл бұрын
I have a question. I have 4 kicker 4 ohm Cvr's and currently running 2 ohm on a Nemesis audio 3k amp and its just not enough bass for me. Could I wire each pair at one ohm? Please answer this. Thanks!
@mellostackzz8753
@mellostackzz8753 7 жыл бұрын
why am i watching this im only 13😂🤷🏾‍♂️ i really cant wait till i get older and buy my own car and stuff🙃hurry up time🙃
@OfficialMarkieB
@OfficialMarkieB 6 жыл бұрын
Just wait your gonna wish you didnt have to worry about paying $500+ a month to own the car and another $125+ (which is great for a 25 yo) for full coverage insurance. Your gonna regret it getting old.
@tfunktofani
@tfunktofani 2 жыл бұрын
I need to kno if I can hook up a Kenwood 4 ohm 500 watt rms with alpine 300 watt rms 4 ohm to a amp that has 4 ohm x 2 400 watt rms, idc if it's bad for alpine I'll get another Kenwood down the rd or should I just put Kenwood in dual 12 ported box for now ?????
@instaboiidsg2117
@instaboiidsg2117 7 жыл бұрын
You F*****G welcome. HAHAHAhahaHA
@randyruth4788
@randyruth4788 5 жыл бұрын
Got 1cozmilk15 2 coils Andy need it to be 6 omh how do I wire it
@distortedfocus7698
@distortedfocus7698 6 жыл бұрын
At 4:00 in series wiring if one bulb blew they would all stop. In parallel however only that load would stop but the others would still be powered.
@nathanielguffey875
@nathanielguffey875 6 жыл бұрын
I’m strapping amps and was wondering is 2ohm 4K watts the same as 1 ohm 4K watts or does the subs react differently as in doesn’t move as much cause of resistance or does it move the same sound the same cause it’s still 4K watts
@Qualitymobilevideo
@Qualitymobilevideo 6 жыл бұрын
Well the stable impedances of the amplifier and subwoofers dictate how you can wire your specific subs and what loads you can make at the amplifier. A 1 ohm load gives you the most possible power from your gear, however you will sacrifice efficiency and the system will run hot. A 2 ohm load with be able half the output on the same amlpifier, but will be more efficient and run cooler.
@nathanielguffey875
@nathanielguffey875 6 жыл бұрын
So basically it’s better to run 2 ohms if you have the power to run your subs that they won’t act differnt 1 ohm or 2 ohm as long as they have 4K watts
@angels_gaming8309
@angels_gaming8309 5 жыл бұрын
I have my two 12" Kenwoods connected to a mono block kicker amp in parallel and the first sub looks like it is getting more power than the second sub. How would I wire them so I have an equal amount of out put to both subs?
@Qualitymobilevideo
@Qualitymobilevideo 5 жыл бұрын
What are the exact specs/models of the subs and amp?
@mike814031
@mike814031 4 жыл бұрын
At 7:12 can we go a little deeper and could you explain why the parallel formula is what it is? Why exactly do they differ, other than the obvious reason they are different types of wiring
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
So parallel wiring offers lower impedance possibilities, like 1 ohm, which means more power, but also less efficiency
@chevva1
@chevva1 4 жыл бұрын
Just a quick question, I have an underseat active pioneer sub installed and am wanting to add a separate bigger 12 inch active subwoofer, I plan to use a new wiring kit for the new sub , split the rcas at the amp end ,but the main question is can I run 2 amps with 1 remote wire, from the head unit splitting into 2 , I hope to install 2 switches up the head unit end using the remote wire split into 2 , then in theory I will run 2 remote wires to the back ,one to each amplifier, that way I can turn each amp on and off for different situations easily, does this sound like it would work OK? Or would I burn the remote wire out powering 2 amps and adding switches?
@shaheenms5790
@shaheenms5790 5 жыл бұрын
Hello, My B&O Amplifier have Dual channel output for Subwoofer, And Subwoofer is also Dual channel (100 W + 100W) (8ohm+ 8ohm), Now I am planning to add one Dual channel subwoofer of Same configuration because of too much vibration, How I will do wiring?
@Qualitymobilevideo
@Qualitymobilevideo 5 жыл бұрын
Can you send me the exact models/names of both the amplifier and the subwoofer?
@shaheenms5790
@shaheenms5790 5 жыл бұрын
Quality Mobile Video Hi, It is B&O Sound System in Audi A3 8V -15 Channel Class D Amplifier-Out of 15 channels 2 channels are for Subwoofer (100 W+ 100W) (8ohm + 8), which is connected to a dual coil subwoofer (100+ 100). Because of too much vibration from rear parcel tray, I am planning to add one more dual coil subwoofer of Same configuration in the spare wheel. My intention is that I have to equally divide Amplifier load to 2 subwoofer Hope you understand
@Caprice1977
@Caprice1977 3 жыл бұрын
Question , if I have a dual 2 ohm subwoofer put I only use one side of each subwoofer to get 1 ohm load ,does that mean Iam only using half the subwoofer because I only used one side of the coil
@the_allamerican7057
@the_allamerican7057 4 жыл бұрын
I doubt it but would parallel wiring work with one DVC and one SVC?
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
You don't want to mix different kinds of subs in terms of specification, always try to use identical subs
@the_allamerican7057
@the_allamerican7057 4 жыл бұрын
Quality Mobile Video alright thanks. So if they’re the same specifications then I should be good. I know it’s better. But do they necessarily have to be the same bran
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
But they're not the same specifications. You said one is a DVC and one is a SVC
@the_allamerican7057
@the_allamerican7057 4 жыл бұрын
Quality Mobile Video I meant if they’re both DVC but not the same brand. Same wattage but different brand.
@sonnelostaan3243
@sonnelostaan3243 5 жыл бұрын
Hi i have two subwoofer total 800rns i used mono black 1200rms at 1ohms its good combination thanks
@Qualitymobilevideo
@Qualitymobilevideo 5 жыл бұрын
Impossible to tell. Are the subs DVC or SVC. Are they 2 ohm or 4 ohm. Are they 800W RMS each or combined?
@sonnelostaan3243
@sonnelostaan3243 5 жыл бұрын
Quality Mobile Video this combined 2 sub DVC 400rms each
@jorgebadillo8755
@jorgebadillo8755 3 жыл бұрын
So 1 questions are subs louder in parallel? Becuase when i wire in series its less bassy Even tho the amp is powerrfull enough that i can easily blow the sub or ao i just need to wire in parallel and increase the bass on the amp it self ?
@Qualitymobilevideo
@Qualitymobilevideo 3 жыл бұрын
Every situation is different and completely dependent on your gear. Parallel will get you a lower impedance which means more power
@joannedodie3136
@joannedodie3136 4 жыл бұрын
When you connect the wire to positive and negative which wire would it be? Positive or negative?
@christopherwise7067
@christopherwise7067 4 жыл бұрын
what? if you hook a positive to a negative, you tend to get a short circuit. if you have a speaker with two voice coils, and you hook a wire on one positive and run that wire to the negative of the opposite coil, (the coils are usually separated by the positive and negative of one coil being next to each other on opposite sides of the maganet.), this is starting to hook them up in series. you would then take two other wires and hook one wire to the empty positive terminal and the second wire to the empty negative terminal and hook those up accordingly at the amp. this increases the total resistance of the speaker.
@joannedodie3136
@joannedodie3136 4 жыл бұрын
Christopher Wise never mind I know how to now :)
@OakStCustomz
@OakStCustomz 6 жыл бұрын
If I wire in series with 2 400 watt rms DVC 4 ohm amps I can get 1 ohm or 4 ohms. Does this change my required amplifier output or will the subs still need 800 watts at least coming out of the amplifiers one channel?
@Qualitymobilevideo
@Qualitymobilevideo 5 жыл бұрын
Actually with that setup it's 1 ohm parallel wiring, 4 ohm series wiring. Your amplifier dictates the power. If the amplifier does 1 ohm, and you wire them parallel, that 1 ohm rating is the power. If it does 4 ohms and you wire them in series, that 4 ohm rating is the power now.
@OakStCustomz
@OakStCustomz 5 жыл бұрын
Quality Mobile Video got it! Thanks!
@alexwilliams1108
@alexwilliams1108 4 жыл бұрын
question--- I have two pioneer champion series 12" one is a 4 ohm single voice coil and the other is a 2 ohms dual voice coil.Now is it ok to series the dual 2 ohms up to 4 ohms then parallel it with the 4 ohm single vice coil so drop down to 2 ohms?
@henryg5650
@henryg5650 6 жыл бұрын
The dual 4-ohm subwoofers included in my package are pre-configured and wired up inside of the subwoofer enclosure at a 1-ohm final load. How do i wire from enclosure terminals to the mono amp.
@lowhertzhighspl
@lowhertzhighspl 4 жыл бұрын
I dont understand why I wired my set-up to 1-ohm but it rests at 1.5 ohms. I have two 4-ohm DVC subs. How do I get it to one ohm? Thx Pros!
@christopherwise7067
@christopherwise7067 4 жыл бұрын
are each voice coil 4ohm? if so, hook those in parallel, that drops total speaker to 2ohm. then hook both speakers in parallel and that will drop total resistance to 1ohm. keep in mind, not all voice coils are created equally, each coil can have a different resistance. when the math is done it's very well possible to come to 1.5ohm. also possible your multi meter has a natural .5 resistance between the leads.
@bvel93
@bvel93 4 жыл бұрын
I have a Rockford Fosgate prime 1,200 Watt Class D- Mono Amplifier, that i want to connect to 3 Rockford Fosgate Punch P3SD2-12" subs. They are (400W RMS) Shallow Mount Dual 2-ohm. What would you recommend to be the best way to wire these so i can get the most power and the least resistance?
@lowhertzhighspl
@lowhertzhighspl 4 жыл бұрын
QUESTION: An answer please?! Can I get 2 two ohm dvc subs to work with one 1 ohm amp that has two speaker outputs? If so how would I need to wire them? I don't see why not as long as the mono amp has dual outputs which it does considering I've already done this set-up for one 12" dvc 2 ohm sub, (but now want to add a second sub) so if wired correctly I'd think I can with two L7 12" dvc 2 ohm subs (connect at 1 ohm to one mono 1500.1 or 2000.1 Skar amp) THANKS IN ADVANCE!
@jezquintero7208
@jezquintero7208 3 жыл бұрын
Soooo this means that if i have 2 single voice coil subs... That are 4omhs and i wire in series... They turn to 1 8 omh woofer which i acn use on a home reciver that is 8ohms?
@bigtg42
@bigtg42 4 жыл бұрын
so i have 3 12s W6 oldschool subs with a JL audio500 amp ......what best way to set up ? series or parallel ?
@zachneal3100
@zachneal3100 4 жыл бұрын
So i have a dual voice coil 4 ohm sub 1800 watt max and a 600 watt amp should i just hook it up parallel
@Qualitymobilevideo
@Qualitymobilevideo 4 жыл бұрын
I need more info on the sub and amplifier. What's the sub's rated RMS? What model is the amplifier? What is its power rating at each impedance
@zachneal3100
@zachneal3100 4 жыл бұрын
@@Qualitymobilevideo well the amp is a sony exploid 600 watt the speaker is a planet audio 1800 watt max i belive it said it had a 900 watt rms thats all i know i think im just going to hook it up parallel
@zachneal3100
@zachneal3100 4 жыл бұрын
So i bought a 2500 watt amp 450w for 1 sub @4ohm My sub is a 1800 watt 900w ohm is it to much amp for the sub i started smelling the sub so i turned the gains down and the bass boost i turned to half and the low boost to half dosnt sound distorted just wondering if i should have went with a lower amp
@zachneal3100
@zachneal3100 4 жыл бұрын
900 rms not ohm mybad
@zachneal3100
@zachneal3100 4 жыл бұрын
Never mind i just fucked tht speaker off to. After having it hooked up for about 5 min and i didnt even have it slamming to hard idk what to do maybe next time i should get 2 subs instead of 1
@timoromeo7663
@timoromeo7663 5 жыл бұрын
Ok how about this scenario: I have 4 dual voice coil automobile (4 ohm-each coil) LF drivers. I need an 8 ohm single channel . What do YOU do?
@AntDaddy1977
@AntDaddy1977 5 жыл бұрын
Wire each you dvcsubs in parallel that gives you 4 subs with 2 ohm each, wire the 4 subs in series to each other. That should give you 8 ohms.But I have never done this. And I may be incorrect but I think I'm right as long as you don't bridge the amp assuming all 4 subs is being connected to one class d mono amp.But I'm guessing at that .So we need to know what your gonna power said subs at 8 ohms total
@AntDaddy1977
@AntDaddy1977 5 жыл бұрын
Excuse me I see now you have one channel amp ok then should be good
@timoromeo7663
@timoromeo7663 5 жыл бұрын
Anthony Tucker Very good. You got it right. 👍🏽
@christopherwise7067
@christopherwise7067 4 жыл бұрын
@@AntDaddy1977 more like why would you want 4 subs at 8ohms total? if your amp is stable at 2 ohms, cause my 600watt rms mono class d is stable at 2ohms. why wouldn't you just run them at 2ohms? you are forcing the amp to hold back based on the resistance of you speakers. at 8 ohms on a mono channel class d, you're probably getting 60watts out of it.
@angelr.9314
@angelr.9314 7 жыл бұрын
Quick question I have a Kenwood 1800 w max mono class D amp with 2 alpine typeR red line speakers. Any recommendations on how to connect or run the speakers. Right now it runs hot and cuts off if I run it for more then 10 or 15 min.
@jgray95903
@jgray95903 6 жыл бұрын
I could help, but I need more info on your speakers. Do you have the 12in dual 2 ohm or 4 ohm speakers?
@moutiabelhedi9381
@moutiabelhedi9381 6 жыл бұрын
quick questiopn please Ihave an Alpine PDX -M12 wired to a capacitor hifonics 1F and an Alpine Type R 12 inch dual 4 ohm and a pioneerDEH-80 prs would I wiring on 2ohm or 4ohm (in a small car -MINI-)
@staylowkey7854
@staylowkey7854 3 жыл бұрын
Hello can I wire 3 loudspeakers in parallel?
@bigd7274
@bigd7274 3 жыл бұрын
Can I use a audiopipe 1600 on dual voice core 2 ohm 2 15 kickers
@tattooedsoutherncali805bik3
@tattooedsoutherncali805bik3 3 жыл бұрын
So when it says4 ohms: 125 watts x 4 chan. Does that mean 125rms per ch or 125 together
@travisultimatetv
@travisultimatetv 5 жыл бұрын
would this be fine if this is the way i want to connect my speakers, 8 ohms sub plus 8 ohms mid in parallel = 4 ohms, 2 8 ohms tweeters in series = 16 ohms then combining the two pairs in parallel connections in sakura av 735 amps?
How Do You Match Car Subwoofers and Amplifiers?
12:13
Quality Mobile Video
Рет қаралды 1 МЛН
Single vs Dual Voice Coil Subwoofer - Which is BEST? Wiring Explained!
9:51
CarAudioFabrication
Рет қаралды 104 М.
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 42 МЛН
amplifier and box testing video m.8593849477
2:47
Sargam Music Centre
Рет қаралды 393
How to wire multiple subs to your amplifier | Crutchfield
11:54
CRUTCHFIELD
Рет қаралды 319 М.
Everything  you need to know about Subwoofer Ohms: Series vs. Parallel
8:12
4 Mistakes that Kill Bass - Car Audio Subwoofer Improvements!
12:06
CarAudioFabrication
Рет қаралды 4,7 МЛН
INGENIOUS TOOLS YOU'LL WANT TO BUY
20:54
TechZone
Рет қаралды 48 М.
Understanding Speaker Impedance and Speaker Switches
7:10
Geoff the Grey Geek
Рет қаралды 2,8 МЛН
Wiring Your DVC 4 Ohm Subwoofer - 2 Ohm Parallel vs 8 Ohm Series Wiring
6:07
Quality Mobile Video
Рет қаралды 757 М.
How to Match Your Subwoofers and Amplifiers - Part 2
5:52
Quality Mobile Video
Рет қаралды 198 М.