Very good video. Thanks for doing this, you saved me a lot of time reading through some very poorly translated instruction. Just a suggestion for a video this long, but you may want to add a table of contents so we can skip to the function we most want to program in. For Example DUAL WATCH 6:40 SQUELCH 7:27
@R2DMD8 жыл бұрын
Yes, that's a good idea. I will consider adding contents. Thank you for positive comment.
@powerbatterychannel43154 жыл бұрын
Самый чёткий видеоролик по данной рации. Спасибо!
@willwindham51187 жыл бұрын
This was a very helpful video. I now see that some of the problems I had were because I was in the wrong mode. Also, you can stop the scanning by briefly pressing the PTT key.
@R2DMD7 жыл бұрын
Thanks. Yes, that way to stop the scanning wasn't obvious for me at that time.
@ondra307 жыл бұрын
Hi again, did you know you can exit the scanning by tapping the PTT button instead of turning the radio off? ;)
@R2DMD4 жыл бұрын
Yes, I discovered it only after I completed the video. Thanks for watching and commenting!
@perryking87207 жыл бұрын
Very Good Video! Much easier to follow than the manual.
@davidthomas8175 Жыл бұрын
How to stop the Scan mode - use PTT Short answer: The PTT button on the side is also an "escape" button. When scanning through frequencies or memories, there seems to be no way to stop the scan mode. The manual is silent on this detail. Here's the secret: Use the PTT button to escape from scanning modes (halt the scan). Don't worry. The transmitter does not transmit when the PTT is enabled as the escape button for scan modes. They designed it this way, but forgot to mention it in the instruction manual. You can confirm this by placing the radio into scan mode and then press and hold the PTT button and you'll see that it is not transmitting. The next time you press the PTT it will transmit. So be careful with double-pressing...
@R2DMD Жыл бұрын
You are right. Thanks for the comment.
@ИринаКиселева-е3г2 жыл бұрын
Thanks you so much for very helpful video!
@smokiibear01Ай бұрын
can you put upper and lower channel in name mode, or only the top?
@cqdx167710 ай бұрын
İs it possible to open TX this radio to Russian River frequency 300-336 MHz? Or only >360 MHz is possible ?
@pietromusian67465 жыл бұрын
Very Good Video. Very helpful. I have one question> Is it possible to Change the Time Display Light? Thank you Pietro
@R2DMD5 жыл бұрын
Hi. Not possible.
@marquismaintenance4 жыл бұрын
I have a couple of Quansheng TG-45AT radios, how do I change language from Chinese, to English?
@edwingenetia68083 жыл бұрын
When i transmit the receiver did not hear me very lowvolume is it already in high power what is the posible problem
@45AMT7 жыл бұрын
Very Good Video. Very helpful. Much better than the manual. Thanks for all the help. AD4JH
@danielrosagrata6 жыл бұрын
Hello. Great video! :) Just a quick question - can this unit TX on the UHF3 band (470MHz-520MHz)? The specs that I am reading says that it can only RX. I am hoping you may have the answer. I appreciate your time in advance.
@R2DMD6 жыл бұрын
Hello! Thanks for positive feedback. The 470-519 MHz band is receive only on this radio.
@kvmods4 жыл бұрын
Nice video my friend, ive learnd alot now :) i hate reading poor manuals
@R2DMD4 жыл бұрын
Really glad the video helped you
@kvmods4 жыл бұрын
do you know where you can buy the scramble board? to solder in
@R2DMD4 жыл бұрын
@@kvmods no, I've never seen it on sale
@lenwhite99017 жыл бұрын
Do you have any experience with Wouxun, Model UV3D? A friend bought these and I'd like to program ours together.
@R2DMD7 жыл бұрын
Hi. I do not have experience with UV3D.
@atze9417 Жыл бұрын
Hey! So I have followed your guide. But I have a problem. I can transmit audio to another (baofeng) and they will receive. But if they transmit I can see on the display that there is something happening. But the noise will be gone and you hear nothing. Tried squelch and scrambling but I have no idea.. Can you help?
@R2DMD Жыл бұрын
Hi! Make sure no CTSS/DCS codes are enabled for receive.
@atze9417 Жыл бұрын
@@R2DMD Yes I eventually figured it out, apparently I didnt setup the receive 6.25 something khz in the menu
@lenwhite99017 жыл бұрын
Starting at 17:30, you walk through how to program in a channel number for a frequency. I'm able to type in the frequency I want, but when I click F and then MR/VFO, it just does a double beep and goes out of function mode. It doesn't bring up the SAV option on my screen. It's like that function is locked. What may I be doing wrong?
@R2DMD7 жыл бұрын
I'm not sure whether it is you doing smth wrong or the radio. Here is a flow I will use: 1) First make sure small arrow is pointing to the upper row (MAIN) 2) Then make sure you are in Frequency mode instead of Channel mode (MR/VFO) 3) Then save current frequency in a channel: F+MR/VFO => (asks to save) => UP/DOWN(to select channel) => MR/VFO => MR/VFO
@lenwhite99017 жыл бұрын
My problem was I was trying to program and save the sub/bottom channel on the radio. Once I inverted them and saved it in the main/top channel, it worked fine. Thanks for your help.
@Fenda684 жыл бұрын
Hi there, would you also make a manual for TGUV2 Plus, please? Thanks a lot
@R2DMD4 жыл бұрын
Hi! I do not have this radio at the moment. If I manage to get my hands on it, I will do.
@lenwhite99017 жыл бұрын
I'm considering buying a couple Baofengs as well. There are a lot of options though. Any suggestions on what is a good price vs. capability option? Since most of these will be for some others in my party, I'm considering the 888s. Don't want to buy a piece of crap though.
@R2DMD7 жыл бұрын
888s radios are good choice: easy to operate and work well for short-range communication (car-to-car when driving together, paintball, neighbors). But: - they are UHF only (not as good for forest as VHF), - you will need to program them from PC, - you may want a larger battery. Expected distance: 3-4 miles in a field (line of sight), 1-2 miles in a small town, less than a mile in a forest. Other Baofengs are basically the same 888s + screen/buttons + VHF.
@lenwhite99017 жыл бұрын
Good to know. I don't mind programming from computer. But want VHF. I use these in my race car and also have a group of guys who beat around in the woods that would use these. Any suggestions on which baofang has VHF capabilities for a good price?
@R2DMD7 жыл бұрын
I would suggest BF-UVB2 or UV-5R. But they cost more. You can find them at ~ $30 at aliexpress or ebay
@lenwhite99017 жыл бұрын
I ended up getting the UV-5R. Thanks. Do you have any training videos on that?
@R2DMD7 жыл бұрын
Good for the purpose. Hope the new radio will meet your current needs. I did not make specific UV-5R video, since plenty of information about this radio is already available. In my videos you can find it only in tests: Distance test: kzbin.info/www/bejne/fmmomIBjipWWe7c Receiver comparison: kzbin.info/www/bejne/e2jRiKispNNpmLc
@keenan23125 жыл бұрын
how to tx UHF3 "F4" - 470 to 520 MHz ?
@Rzut-Oka6 жыл бұрын
Hi how to set 470.625 and use? I have "DIS" on screen and long "beep" sound ?? Thanks for that video is very usefull:)
@R2DMD6 жыл бұрын
Hi! TG-UV2 can only receive at 470-519 MHz. It cannot transmit at this range. You can try unlocking F4 frequency band, but stable work is not guaranteed.
@Rzut-Oka6 жыл бұрын
R2DMD ok thanks, i have "plus" version in 4000mah battery and 10w power but like l see that menu is the same like in older model.
@depeichow153614 күн бұрын
@@R2DMD Hi, may I knw how to unlock the F4 Frequency band?