Quick Polaris Sportsman 500 Carb Repair

[@jasonwilliams7167]

When he dropped that screw out of the bowl and the look on his face... I felt that on a level higher than ever before.

[@clevernamehere7559]

I have a 2000 sportsman 500 in need of some serious attention, I’ll have to grab it with the tractor here shortly.

[@gamemixer640]

Really helps thanx for the video FYI I have a 700 that I am working on

[@michaelnelson1911]

You are so knowledgeable about the 2000 Sportsman 500. I wonder if you could give me some guidance and direction on a problem I have. I dropped a paper cap from a fuel stabilizer into the gas tank by accident. I can't think of any way to get it out. How hard is it to get the gas tank off. Or maybe you have another way to get it out. I feel like I need a trick here. I really don’t want to take the tank off. I have taken the seat off and the side shields. I was hoping that I wouldn't have remove all of the shields to remove the tank.

[@jakesburnoutgarage6527]

The tank is fairly easy to remove if you have the side platics removed. I believe its 3 bolts, but you might have good luck draining the tank, then removing the petcock from the bottom of the tank and possibly the paper will have settled there as the fuel drains and you can use a small pick to fish it out. Otherwise your best bet is to pull the tank(which you'll have to disconnect the petcock), and rinse it out to remove the paper, or let it dry and try to blow it out with an air compressor. Should only take you 10 or 15 minutes to remove the tank from where youre at now with the seat and platics removed.

[@sodaktx]

There's a clear tube coming from the right side of the carb, where does it route to?

[@franciscofernandez1824]

I wanted to know how it comes out and how goes back on ... to bad it doesn't show

[@jhonnygonzalez7799]

One question is the 2 hoses that are looked at in the filter box. Where are they connected?

[@shawnb4027]

I know this is a stupid question - but can i biy a new carb and just put it on or are there adjustments to be made

[@jakesburnoutgarage6527]

It depends on where you live. Most carbs come set to run at sea level. So you may have to change the main jet or adjust the needle.

[@robertstoll1699]

What is your median rod setting? I'm having a problem on full throttle bogging down

[@dellis911]

I'm looking for a video on how to remove my carburetor. You fast forward through what I need to see. Doesn't help me, I have to look elsewhere....

[@carlosrobles2048]

So fucking look elsewhere! And thanks for informing us!

[@Wa_ge123]

I can’t get my carb to fit back into the tube that goes into the engine

[@vouguesonredchronicleshust5745]

I dont have any idea where does it goes is a hose that connect 1 side to the other of the carb and makes a 3 line way and directs goes to the atv frame on the left side.

[@carlosrobles2048]

Atmospheric vent

[@vouguesonredchronicleshust5745]

Question what u that clear hose that goes into the atv frame

[@carlosrobles2048]

Vent

[@mattgrill7713]

There's a brass nipple coming out of the I take just fast the rubber carb boot can you tell me ware the hose goes of of the nipple I been pulling my hair out trying to figure it ou

[@mattgrill7713]

That was spose to say intake

[@timschannel910]

So what was wrong with it

[@jakesburnoutgarage6527]

It was just normal wear and tear. The needle had just worn out and the carb was leaking. There was ove 4500 miles on the 4wheeler at the time i made the video. Almost 6k on it now and the carb is still great. I just ordered a rebuild kit for it off amazon.

[@sandersisiah]

Is there anyway I can contact you

[@larrywillard2489]

Our box 😂 only watch the video to see how many times he said our box And not Air box