LOL True 1st video you put the last plate wrong but You correct it unknowingly at the end of this video 2nd . But I like the video of how to remove with out taking oil out 2
@azzkam89724 жыл бұрын
Lol Thanks mate I appreciate it
@sebzuk4 жыл бұрын
I have just checked mine today because I had some noise from it and problem with the gears, turned up that was wrong 2. It was replaced couple months ago by mechanik. I have changed the last plate now and the clutch is quite and the gears working fine so far. Tx
@dz77867 жыл бұрын
Alot of ppl make mistake when reinstalling cover and can't get enough pull on cable to disengage.i wonder if your still a little off and not getting full pull and that's why adjusting between hot and cold.when installing cover cable must be unhooked and usually using 2 hands,one holding the arm rearward some and the other to start sliding cover on, as lever rotates forward as cover going on,that's why need to start out holding back some.once think have right move lever w fingers and should feel stiff near where dot and arrow line up.i think your prob just a CPL splines off
@azzkam89727 жыл бұрын
darren Z thanks for the input, I’ve taken the clutch cover off several times before and I’m pretty sure it’s on correctly and the arrow and dot are aligned, I’m pretty certain this issue was being caused by the judder spring but we’ll see how it goes
@EddieLiu12176 жыл бұрын
Hello,Azz Kam. Has the problem been resolved? I got the same freeplay issue on my zx-10r. It goes excessively slack when the bike warm and tight when it cool down.
@laservlx3 жыл бұрын
That sounds exactly what wrong... Personally I just remove the judder spring and spacer on all my bikes. It's not needed. Just make the clutch smoother.
@moekakke4 жыл бұрын
2:27 you got the first plate to take out installed wrong. The first plate to take out or the last to place in should be in the other groove on the basket. That is the only plate thats sits different.
@bullinapeamurica59402 жыл бұрын
What do you mean in the other grooves on the basket? There's only 1 way to install the plates.
@moekakke2 жыл бұрын
@@bullinapeamurica5940 Dude don't check this guy's videos he does not know how to work on a bike... Creating problems himselve... Check this link how the firt plate should be when you open a factory fresh clutch... kzbin.info/www/bejne/Z2qseHylmdB7pJI and also check this dude his other video where he installed the clutch mod the wrong way at 10.38... kzbin.info/www/bejne/gJvEZIKghrmZfsk. If you don't see the details yourself you also have a problem dude !!
@mechanicalman4531 Жыл бұрын
@@bullinapeamurica5940 no, the last friction plate installed is supposed to be offset by one groove. Its says so in the manual, same in the fz1 which uses the r1 motor.
@suspensefulness4 жыл бұрын
my cable soo tight i cant engage anything or adjust.its either way too loose or too tight to engage gears ,is something off on new clutch plates install
@Ss14r12 жыл бұрын
Mine's doing the same what did it end up being
@bullinapeamurica59402 жыл бұрын
@@Ss14r1 you got the little arm installed wrong probably, make sure the triangle lines up with the dot after you put tension on the cable so the triangle on the arm should be a little to the right of the dot then when you put tension on it they should line up
@kristitanellari4 жыл бұрын
I replaced my clutch about a month ago and now the bikes vibrates. when I pull in the clutch the vibrations go away. anyone know what the problem could be?
@dekic132364 жыл бұрын
broken spring/s on clutch basket
@suspensefulness4 жыл бұрын
did that fix that problem
@freedom2401884 жыл бұрын
Hi bud my clutch seems to be slipping wet hot but only do it some times wat you think ?
@azzkam89724 жыл бұрын
freedom240188 first thing id check is the clutch free play and if all is good then check clutch cable and replace if it’s stretched out, and then look at replacing the clutch itself depending on the mileage and when the clutch was last replaced etc, I hope you get it sorted mate
@jeffreyrice31415 жыл бұрын
Hi Azz Kam . Great vids mate. I've just changed clutch, metal discs and springs on my 2004 R1. Yep.... putting the clutch cover back on is a bitch until you get use to it. Quick question... Is the clutch basket/hub standard or aftermarket ??? It looks different to mine. (The oil filler cap on the clutch cover is in a slightly different position too) I'm in Australia so it might be different specs for different countries. Cheers mate.
@azzkam89725 жыл бұрын
Jeffrey Rice your 5vy is lightly different to my 4c8 glad you like the vids thanks mate.
@milanalberto92223 жыл бұрын
You prolly dont give a shit but does any of you know a method to log back into an Instagram account..? I was stupid forgot my login password. I would appreciate any help you can give me
@kylancorey69833 жыл бұрын
@Milan Alberto instablaster :)
@milanalberto92223 жыл бұрын
@Kylan Corey i really appreciate your reply. I found the site on google and I'm in the hacking process now. Takes a while so I will get back to you later with my results.
@milanalberto92223 жыл бұрын
@Kylan Corey it worked and I finally got access to my account again. Im so happy! Thank you so much, you really help me out !
@tevincurry15213 жыл бұрын
I’m so confused because I have taken them out and made a better et
@theforester_4 жыл бұрын
hi mate, isnt that normal? cos when the oil warms up and the plates and discs warm up aswell they probably get thinner or thicker so the free play will automatically change? my bike does it aswell and it doesnt have the judder spring.