RC Factory Clik 25 Review | Build, Test Flight & First Impressions

[@brianbezayiff8631]

I got mine in the mail today. My 1st indoor plane. I'm really excited to try it out .

[@MattTakharRC]

Cool! I love flying mine. Can’t wait to get another session booked in. I now have the Synergy too, which is ready for the first flight.

[@eggertneistrup5238]

Designed by mr David Kyjowski from rc factory. Excellent pilot and great constructeur of foam models 😊

[@MattTakharRC]

I love this plane! Flew it again yesterday.

[@andyshutt299]

Good video Matt, the upper and lower aerofoils are called canalysers, mainly from the F3A world. Hope to see some flight videos after you have had a few flights on it, shame that F3P did not take off here in the UK.

[@MattTakharRC]

Thanks Andy. I flew it yesterday but was hard to film as I was by myself. I also took the Synergy out for the first time. That video should be out next week. 👍🏽

[@TL_RC]

Nice looking model, the surfaces are called Canalyzers.

[@MattTakharRC]

Thanks. I had a complete brain fade 👍🏽

[@PaulThomas-s1d]

Good afternoon, Matt Nice to see you build the RC clik 25 With reference to the glue that you’re actually using on the aeroplane, honestly is no good The glue that we use is UHU por the reason why we use this glue is it’s very elasticated and any mistake that you actually make you can rectify it without any damage to the Aeroplane Kind regards, Paul

[@MattTakharRC]

Hi Paul, Thanks for the feedback. I was told that by someone else after my build. I’ve now got the UHU and will use it next time round 👍🏽

[@colinsmith4699]

A great video

[@MattTakharRC]

Thank you!

[@racnc1]

Also if possible show video of that small RX wiring set up. I use very small rx from eBay with my spektrum tx. I haven’t seen the one you showed.

[@MattTakharRC]

I will do. I’ve not yet wired it. I swapped over to some small Futaba RXs that had normal connectors.

[@turboomni848]

Just finishing mine . Seems to fly very well for you. Any idea on your weight? Also how much control throws and expo? CG as per manual? What propellor do you use? I bet you would take another 4 grams or more off with a smaller receiver. On a model like this it would make a noticeable difference. Congrats on your Clik25 and wish me luck on mine!!

[@MattTakharRC]

Hi, thanks for leaving a comment. The my Clik weighs 141g with a 250mAh battery, although that was with the bigger RX as shown in the video. I the RX and is now weights 119g without battery. Sorry I don't have a direct comparison with batt. I'm using the GWS 8 X 4.3 which comes in the RC Factory Equipment set, I've not experimented with other pros yet. CG is as per manual, although I want to double check it on a balancer. It does fly fine but I want to make sure. Let me know what you think of yours.

[@turboomni848]

@@MattTakharRC Thank you for the reply and info. I also saw your Synergy video. Depending how the Click turns out for me I may give the Synergy a go also. Overall between the two planes you seem to be able to fly the Clik abit slower more easily? I also hope you got an even better job than before! Happy to have found you ,Subscribed.

[@MattTakharRC]

@@turboomni848 thank you for subscribing. I think the Clik is a bit slower. I'm about to glue the "air breaks" to the wings, which will slow it down further too. I'm hoping it will slow it down during the downlines too.

[@thomasjonsson2186]

Hi did you find out what the white sheet with parts you showed in the beginning of the video. /Thomas

[@thomasjonsson2186]

The part is at 2.55 in the video

[@MattTakharRC]

Hi. Yes they are for air breaks that get attached to the wing. I’ll put them in soon and put a few photos on my Facebook page for you.

[@racnc1]

I don’t like those keepers. I prefer to use paper clips. I cut them and do Z bends and heat shrink tubing with some thin ca.

[@MattTakharRC]

That’s a good tip. I’ll try that next time. Thanks.