Reach RS2: Placing The Base Over a Known Point

[@taiwoolaniyan4740]

Thanks for the video. Please how do input coordinate in UTM mode. Replacing latitude and longitude with eastings and nothings. Thank you

[@Emlid]

Hi Taiwo! We'd like to see how we can help you. Please contact us at [e-mail]. Our Tech support team will assist you and provide some guidance.

[@danielacosta6912]

same question. how to input the coordinates Northing and Easting instead of latitude and longitude?

[@Emlid]

@@danielacosta6912 hi there! If you mean base coordinates in the Base mode, there is no way to input Northing and Easting. Base coordinates can be set up in geographic coordinates only.

[@timd9430]

​@@danielacosta6912use NCAT, but still have to enter LLH for base. geodesy.noaa.gov/NCAT/

[@eturn23]

Stupid newbie question here: Are known coordinate points listed publicly somewhere? How would I find them?

[@timd9430]

geodesy.noaa.gov/index.shtml Or pay surveyor to set a benchmark (BM) which is referenced from a known coordinate if too far from your site. Probably easier to just use a CORS point if available in your region... some free, some pay.

[@GNHacks]

Thanks for the tutorial! How do I change the datum WGS84 to Stero 70 and Marea Neagra 75?

[@Emlid]

Hi there, happy to see it was helpful! You can perform datum transformation using our guide: docs.emlid.com/reachrs2/reachview-3/crs-custom-setup. If you need assistance, please feel free to drop us a line at [e-mail].

[@matheusmarques9877]

Thanks for the tutorial! How do I change the datum WGS84 to SIRGAS 2000?

[@summerdeantonio4046]

Correction input settings could inprove Grey bars?

[@Emlid]

Grey bars in the Status tab correspond to the base corrections. Hence, to improve their quality, you should adjust settings on the base unit. Please email us at [e-mail] if you have further questions.

[@sinongol7116]

Hello , do we need any internet connection to do RTK over Lora Radio ?

[@Emlid]

Hi Syukri! For establishing an RTK-link via LoRa radio Internet connection is not required. You can learn more about the base and rover setup over LoRa in our guide: docs.emlid.com/reachrs2/common/quickstart/base-rover-setup/

[@sinongol7116]

@@Emlid thank you. How to set up for static observation?

[@Emlid]

@@sinongol7116 you're welcome! Could you please email us at [e-mail]? We'd be happy to provide you with guidance. Meanwhile, you can also check our PPP tutorial: docs.emlid.com/reachrs2/common/tutorials/ppp-introduction/#how-ppp-works

[@kadry93]

as of right now, can we put UTM Coordinates in manual mode?

[@Emlid]

Hi there! Base coordinates can be set up in geographic coordinates only (UTM provides coordinates in meters). Please contact us at [e-mail] if you have further questions.

[@victorcebotari109]

Do you plan to develop other coordinate systems?

[@Emlid]

We sure do!

[@zarkaalymama6780]

واو نشتي واحده منها باذن الله

[@luisgalina2770]

The base mode is not in ON !

[@Emlid]

Hi Luis, We cover correction output procedure in a different video: kzbin.info/www/bejne/Y3yWY5Svi9J7bLc

[@plamen_petkov]

Because of the termal deformation I would not recommend using an aluminium tripod for base station.

[@gabrielgalina3461]

In base mode correction output is OFF!!!

[@Emlid]

Hi Gabriel, Thanks for noticing, however, to keep the video as simple as possible, we show correction output procedure in a different tutorial: kzbin.info/www/bejne/Y3yWY5Svi9J7bLc

[@temamoller1325]

Spanish please😭