Bolt length -1/2 meter Small disc distance- 22 mm Last 3 bigger disc distance- 12mm,9mm and 7mm respectively
@fernandoadauto53542 жыл бұрын
The material of the discs, what is it?
@gustavoenriquejimenez8098 Жыл бұрын
@@fernandoadauto5354 Anything metalic
@mohamed_rf95516 ай бұрын
What's the name of the connector between the cable and the WiFi adapter please 🙏
@energydrinkdose75854 ай бұрын
@@mohamed_rf9551looks like SMA or RP-SMA
@simonstergaard4 жыл бұрын
Love that green car !
@myotherusername92244 жыл бұрын
ON the door, it says: "TO BERLIN !" (obligatory nod to the Great Patriotic War); this is the spirit that got them there.
@goclunker4 жыл бұрын
Simon Østergaard you love a zaz fiat knock off?
@stoatrepublic4 жыл бұрын
That car has character, love the suicide doors...
@craigwall95364 жыл бұрын
Kreosan, I love your projects, and I'm really pissed off about the people calling this fake. Apparently they've never seen a disc-on-rod wave guide and don't recognize a Yagi with circular polarization. Thanks for this video. I was going to design my own but you've saved me the trouble. And BTW, your translation called your insulator a "gasket" and now everyone thinks the reflector and driven element disk are shorted. Your biggest problem is that your audience is just ignorant and can't figure things out for themselves.
@olivejuice52334 жыл бұрын
Craig Wall but it is fake small little brat
@walkertongdee4 жыл бұрын
U never went to school eh, FAKE DUH.
@mojouk89354 жыл бұрын
You will get all the online weirdos who will get a hard on and counter this comment look above. Internet creeps we have now. lol
@alirezaeskandari22874 жыл бұрын
if you knew any thing about yagis you would not say so
@alirezaeskandari22874 жыл бұрын
they just turn on their phones hotspot
@doxielain22313 жыл бұрын
Ah, remember 2004 when no one secured their wifi?
@justusjonas85062 жыл бұрын
good old days
@capstasher4 жыл бұрын
This guy inhaled his grandpa's experimental internet gas.
@gabrielcoelho23464 жыл бұрын
Screentime!
@flyback_driver8 ай бұрын
Another way to find the center of a circle is to draw at least two (but more helps accuracy) lines of exactly the same length and touch the outside twice. For example if you have a circle with a 4 inch diameter you can use 1 inch lines so long as all of them are one inch. Then go back over each line with a square and at the halfway mark draw a line all the way through. Each intersecting line will also meet in exactly the middle .
@callmetony13196 ай бұрын
I don't know if this method is accurate enough for these kinds of use cases, but an easy way to find the centre of a circle is to pick any point along its edge, zero a ruler on it, and scan the ruler left and right until the measured length at the intersection of the ruler and the edge of the circle is greatest.
@benjaminwesp75842 жыл бұрын
I have build your Wifi-Antenna the way you told in the video. I am impressed! Instead of cupper i used aluminium but everything else remains the same. The quality of this antenna is unbelievable good!
@RahulSharma-ue6sg Жыл бұрын
Hi @benjaminwesp7584 Could you please tell the the latency difference with an without using antenna, and As we increase distance don't we need transmitter and receiver both to be high gain antenna ?
@guanip4 жыл бұрын
suoer excelente, felicitaciones a tu canal, desde venezuela.. es ingenioso las ideas q tienes y eso me gusta ya q aqui en venezuela es dificil conseguir poder de señal.
@furekmody77494 жыл бұрын
I love how this car says "na berlin"
@dt88697 ай бұрын
Super video! How (using which application) did you calculate the dimensions (diameters and distances) for making the antenna?
@wellboyscience84784 жыл бұрын
With 75 ohm cable you will not get better results Because most wifi adapters are rated *50 ohm* (VSWR is important(
@saadachab84254 күн бұрын
yes maybe your are right, but @Ath_ hace 4 años To everyone that says that it won't work: In america you obey laws of physics In soviet Russia laws of physics obey you
@seanmayoaguirre13164 жыл бұрын
Dude, I don't know what's cooler - the awesome sci-fi looking death ray wifi gun or the green automobile...I WANT THEM BOTH!!! Cheers, man. y'all are geniuses! If you came to Los Angeles you could probably trick the whole city into thinking you are INTERPLANETARY WIZARDS. Stay Groovy, Dudes. I Love the Videos!
@zyrppa4 жыл бұрын
At 9:01 that is GPS antenna, not wifi! Connect any metal thing to other end of the cable and results will be same.
@HelamanGile4 жыл бұрын
So basically They boosted their GPS a thousand percent.
@Thomas1124ful4 жыл бұрын
Any metal thing to the end of the cable? No, not really. While it might be still better than the internal antenna it will be nowhere near as good as the shown "wifi gun" antenna. And at the end they connected the cable to the correct pin.
@timsuttonlovinlife-4 жыл бұрын
Man I love this channel it’s awesome 👏
@fantomgaming90184 жыл бұрын
No that wifi
@111chicane4 жыл бұрын
Dumb!
@cjwrench074 жыл бұрын
You need to add in links for the extra products you use. For example: the antenna cable to USB adapter.
@ssswasiim3 жыл бұрын
Yes, I agree with you
@hotboy1979883 жыл бұрын
It should have shielding between the contacts from the outside ground to the copper centre. If you was to do this on say a CB or Ham radio you would burn it up without shielding. I believe the low watt wifi could suffer from long-term use without making the rear shielded from the front over time.
@krunov962911 ай бұрын
it is not critical on this freq....
@adorhambre5973 жыл бұрын
all content of these channel are true unlike other yt channel. love it.
@boubacartahirou91902 жыл бұрын
hello I really like your videos. I have a question between iron, aluminum, copper and zinc which brings more signal?
@dmo8483 жыл бұрын
I just can't stop laughing when he starts to go into town. Jus wow man
@franciscoestrada25522 жыл бұрын
Yes, me too
@aldrinmilespartosa15783 жыл бұрын
"No one can defeat the russian engine ring!!!!" - strohiem but he's russian
@Lorentz19753 жыл бұрын
The usb in the router where you plug in the wi fi adapter is the same usb for the storage (some modem routers have such functionality)
@yourelegantwaifu4 жыл бұрын
I want to see your video being reacted in Electroboom
@cjwrench074 жыл бұрын
You average kid The homemade wind turbine one, would be my vote for reaction video.
@IbraheemKhazbak4 жыл бұрын
THE RECTIFIER
@furonwarrior4 жыл бұрын
He mentions their video about the flying oil.
@yourelegantwaifu4 жыл бұрын
@@cjwrench07 this video especially. They got a lot mistake during the process and some of it doesnt even make any freakin sense
@nvmyutube4 жыл бұрын
its been done.....
@chrismin134 жыл бұрын
FIRST ONE IS 90MM NOT 80MM AS IT SAYS ON THE VIDEO! Had to cross check with the russian Kreosan video and it's 90, not 80. You can see it later in this video as well.2:38
@Abdullah-xz7ue3 жыл бұрын
that's right the original : kzbin.info/www/bejne/e4WVZqOkpdl9lZI
@kitecattestecke23034 жыл бұрын
Nice GPS antenna on the tablet ;-)
@nullbewahrer3 жыл бұрын
Hello Kreosan team, super job & super video, one question: I have build a similar UKW Yagi antenna several years ago and normally the second element (the one which you connect to the core of the coax cable) should be islolated against the whole boom assembly. I did not see any isolation materials for element two in your arrangement. Did you use a short piece of hose plus two plastic washers or something similar ....? Best regards
@tarendra82112 жыл бұрын
same question bro
@krunov962911 ай бұрын
no need for isolating..in fact if You do that performance will be degraded..check your antenna knowledge
@vicdasoldfart48663 жыл бұрын
Very interesing and wih a nice touch of humour. thank you Kreosan
@thomasvnl4 жыл бұрын
One of the most powerful wifi adapters: no its just el-cheapo. Also nice job connecting the antenna to the GPS port of the tablet
3 жыл бұрын
Thomas Verschoof, it is directional.
@alichank4 жыл бұрын
KZbin don't send me any notification. I have luck that i right now turn youtube.
@Drxxx4 жыл бұрын
Press bell notification
@supersolex4 жыл бұрын
wel thats because this antenna is fake
@alichank4 жыл бұрын
@@supersolex what this antena have to yt sending notification system
@youbetterbelieveit81144 жыл бұрын
🤔🤔
@mahmoudzidan74074 жыл бұрын
Hi Man can we make a metal detector like WiFi Gun Thanks
@saulhanson88013 жыл бұрын
These lads are geniuses
@shermansher73364 жыл бұрын
I love your projects
@Richard_GIS3 жыл бұрын
7:38 MegaBITS of course ;-)
@CBKCUSTOM4 жыл бұрын
I love this channel i idolize you sir i want to be like you someday i wish you will visiy philippines and have a vacation here
@HelamanGile4 жыл бұрын
I would love to see you guys make a tincana and see how well it works against this
@gotmullets3 жыл бұрын
That car is Awesome! Classic. 💚💯
@OldisGold-tp1xk4 жыл бұрын
Please provide buy guide of the things used and simple map of it
@bebox4 жыл бұрын
hi, great fun with your videos as usual. can you give us som links for : antenna adapateurs and routeur that accept USB device as source on internet kind regards from France :)
@verynice.mp46134 жыл бұрын
Stéphane BeBoX its being translated i think kreason doesn’t even know this channel exists lol
@ParadiseParadises3 жыл бұрын
RF Coaxial SMA Male Plug to BNC Female M/F Radio Antenna Connector Adapter
@rossydesuarez30623 жыл бұрын
Greetings from Venezuela, would I like to ask you if adding more rings to the antenna would give you more reach? or would it have to be only those that are suggested in the video?
@EzeePosseTV4 жыл бұрын
I have a USB WiFi adapter but it only has a built in (copper track on PCB) antenna. Could you do a video showing how to connect an external antenna to these types of wifi adapters.
@ketansaart15464 жыл бұрын
I love this wifi pushka 🤗
@lordelectron65914 жыл бұрын
Does it push wifi
@dangerousdoggo54654 жыл бұрын
means rifle
@MrDarkLung3 жыл бұрын
Soviet Sheldon Cooper 😃 Awesome!
@johnhoye65843 жыл бұрын
Sheldon cooper was a theoretical physicist. Probably could not use a drill.
@anthonybarroso73862 жыл бұрын
good video friend ... Question: is it necessary to place an electronic component between the positive and negative where the cable connects in the antenna discs?
@SammeLagom3 жыл бұрын
You guys make great videos! I will build this haha
@vainboaster4 жыл бұрын
There is a Problem with the Two Disks that is connected to the stud without insulation thus shorting the antenna circuit. The second disk from the two disks that is connected to the wire should be insulated from the rest of the disks and stud...
@krunov962911 ай бұрын
no....update your antenna theory....at that frequency a galvanic short circuit is not a radio frequency short circuit
@sterben19414 жыл бұрын
Thank for this idea adopting the Yagi Uda antena. Hope you make signal/internet booster to those users who are only using mobile data internet/ users of Free and Paid VPN, no wifi, and the eqiupments are accessible at home because we cannot go to hardware store due pandemic and our age limit restriction.
@usernamenotfound11964 жыл бұрын
everybody gangsta until it's start shinning.
@bjornras4 жыл бұрын
Na Berlina! Towards Berlin - Sovjet WW2 retro with a homemade Yagi-Antenna and a green oldtimer .. But I like the curiosity though
@user-fz2ms8rr7r3 жыл бұрын
Куда я попал Ахахпхах 🤣🤣🤣🤣 Оказывается есть канал инглиш креосан
@user-sr6pi5lp3q3 жыл бұрын
И немецкий есть, только длхлый
@timgore8293 жыл бұрын
You're probably losing most of your antenna's gain in that white coax cable. It's not made for 2.4 or 5 GHz frequencies. Also, is the driven element electrically connected to the reflecting element through the threaded rod?
@flyguille3 жыл бұрын
Yes, the same I though DC short cut!
@fungo66312 жыл бұрын
Satellite LNBs reach up to 2.1 GHz, so for 2.4 GHz a not too long cable should work.
@krunov962911 ай бұрын
cable for satellite receiver is good enough to 10 m
@flightgear11112 жыл бұрын
There are a few simple things you can do to make this even better. One, get rid of that cheap TV coax cable. Technically this antenna should be 50ohms impedance. RG6 ( common cable tv coax) is 75ohms. The mismatch will degrade this signal. Get some decent 50ohm coax. Second, you are using WAY too much coax. Microwave signals for wifi at best are weak, 50-70dBm ( a few milliwatts) the longer your cable the more the signal will be attenuated by the time it reaches your computer. Keep all the coax lengths as short as possible. Finally, the driven element of this antenna ( the 68mm disc you solder the center conductor of the coax to) this needs to be isolated from the boom ( the 8mm diameter screw boom used to attach the discs to) you need to put something on the boom so the 68mm disc is NOT physically touching the boom, like tape, heat shrink) the 68mm disc without this isolation is actually being shorted out. While it will receive some signal, if you isolated it from the boom it will work 1000 times better.......try it!
@krunov962911 ай бұрын
no need to be isolated.....try you theory before comment.....this is exactly as suppose to be, this is not short for 2.4 GHz, not even close
@alizee80043 жыл бұрын
what these lids made of i.e do they have to be copper or just any lid can work also where you can buy them any one?
@pranitkhedekar23884 жыл бұрын
7:49😂
@BeatboxNorwich4 жыл бұрын
The shield and core shorted out, a mile of 75 ohm coax cable with no balun. Seems legit!
@Gamer-nc8qp4 жыл бұрын
i was wondering that too its not insulated
@DavidLopez-bz4rj4 жыл бұрын
Hajaj, yes it is fake.
@craigwall95364 жыл бұрын
It's not shorted. The translation came out "gaskets" when they meant "insulating washer". And no, it's not fake. It's not even new. This is very old technology.
@BeatboxNorwich4 жыл бұрын
Oh, OK. Cheers for that, Craig :) A few of their vids have been called out as fake so I made an assumption.
@denz374 жыл бұрын
nah u got it man
@Jimmylee3144 жыл бұрын
May I know how to calculate the antenna plate wide for this directional antenna?
@djatomist2 жыл бұрын
I had a Cisco Yagi in ~2004 where I was living very close to the pentagon. While trying to pick up free wifi I had it mounted outside my house pointing into the direction of the pentagon. A black SUV pulled up with 2 people in black suits jumped out, took a bunch of pictures. Then they got into the SUV and drove away. Never heard anything from them.
@NewLife-jw9to4 жыл бұрын
Thanks for visiting 🇮🇳 India 🇮🇳 I have seen ur video on hacker OM channel And thanks for the this video 🙏🕉🙏
@NewLife-jw9to4 жыл бұрын
@Tushar Kashyap I said about hacker OM Aur Indian hacker bi hai we can get the knowledge But it's true that they just want views What do u asspect when ur an KZbinr 🙏🕉🙏🇮🇳
@NewLife-jw9to4 жыл бұрын
@Tushar Kashyap haa king of random bi Accha channel hai Aur recently Indian hacker nay chloroform par ek video banaya tha Jo k bhout Accha tha Warna hum to chloroform ko Galat Tara say Samaj rah thay U know by watching the movies like de Dana dhan 🙏🕉🙏🇮🇳
@Kj16V4 жыл бұрын
5:58 Waaaaaiit... Haven't you just shorted out the entire aerial to just two discs?? Aerials confuse the hell out of me!
@edgarbjorntvedt3 жыл бұрын
This is what I think as well. I think this second disc must be isolated from all the other ones to make the antenna work as expected
@krunov962911 ай бұрын
no.... it is just like supposed to be....dc short is not short on 2.4 ghz
@shivercanada4 жыл бұрын
Greetings from Canada, you guys are great!
@sfnyc Жыл бұрын
@ 2:40 didn't he say earlier it had to be 80mm not 90mm (or 9 cm)? Also what's the max speed you can get? The 2.4GHz wifi allows a max of 450Mbps if I recall correctly so that would be the max one could get with this antenna? I assume that it would not be able to work with a 5GHz signal, would that be correct? thanks :)
@oddjobbobb4 жыл бұрын
That car looks like a 1957 Fiat 600D I owned. Suicide doors too, nice.
@gordslater4 жыл бұрын
Zastava 750 i think, so a licence-built 600
@becconvideo3 жыл бұрын
Saporoshez SAS 965 . Made in Ukraine. The original Fiat Seicento stood model for its body but the engines are different- the Sappo has a V4 while the Fiat runs on inline 4 cylinders giving more space to rear passengers in the ukraine model. They were quite common in East Germany too but then less popular than the Trabant. (I don't know why, I haven't driven neither) Now collectors items due to their scarcity,
@DiyEcoProjects4 жыл бұрын
*Kreosan* improvements for you. I read somewhere, to isolate the 68mm disc from the central bolt by putting heat shrink tubing on the shaft. That way you are not creating a short. I dont know if that is correct, just trying to help. All the best guys, youre awesome
@EzeePosseTV4 жыл бұрын
I was just thinking that when he slid the disc connected to the coax screening along the bolt connecting the coax center wire to the next disk without insulating the screen disk. Basically just rendered the rest of the antenna beyond the center wire disk useless. I remember making a CB radio tranceiver out of coke cans in much the same way as Kreo except my antenna was 22 foot high and took over an hour to tune the SWR in properly, lol
@d1s1ntegrator564 жыл бұрын
It may be AC isolated, but not DC. If a modem or other device outputs DC current to antenna - it is going to short out and you can damage device.
@krunov962911 ай бұрын
no no and no....there is no dc and galvanic short is not rf short ...design is good ...why is such many wrong comments on that ? check commercial antenna of same design
@handlesrtwitterdontbelivethem3 жыл бұрын
ur the most magical person and genius love it
@agustinusreynaldi71014 жыл бұрын
In our country, we will even upgrade/modify it with even more cans or aluminium frying pan for more boosting
@gabedaxe66224 жыл бұрын
I’m here for the creen car 🤣
@zikomusic66674 жыл бұрын
Amazing chanel
@HelamanGile4 жыл бұрын
I love your Channel. All your ideas are awesome.
@markarca63603 жыл бұрын
0:14 - The Lunokhod, the Soviet counterpart of the Apollo Moon Rover.
@blise518B4 жыл бұрын
Isn’t that just a short circuit of the antenna cable? There should at least be an insulation between the last disk and the central screw?
@Jorissoris4 жыл бұрын
No, that's not how antennas work. Just like in a Yagi-Uda antenna, it does not matter whether the directive elements are connected to the central boom as the electric field is (supposed to be) almost zero there
@blise518B4 жыл бұрын
Ty for the explanation. Very interesting. I always thought there have to be 2 elements were a voltage difference can be induced or something like that.
@Jorissoris4 жыл бұрын
@@blise518B You're not wrong! The point is that due to the speed of light and the very high frequency of Wi-Fi, there can be a voltage difference even though the elements are not insulated :)
@craigwall95364 жыл бұрын
No, the NEXT to last disk. And the insulation is there but the translator called it a "gasket". (The last disk is the "reflector" and the next to last is the "driven element".
@Jorissoris4 жыл бұрын
@@craigwall9536 There is no insulation there. The narrator called it a gasket but it's clearly just a metal spacer
@sirhaugen10254 жыл бұрын
No! You have to isolate the active part from the ground. This antenna is useless without.. making the antenna like this it will be a short between active element and ground...
@Fortnite-gb7dz4 жыл бұрын
No this is like a magnetic loop
@Fortnite-gb7dz4 жыл бұрын
Even a biquad antenna has a short
@sirhaugen10254 жыл бұрын
Nicolas Springer : No. A yagi antenna is nothing like a Biquad or Magnetic loop.
@kaleenbhaiyya98434 жыл бұрын
U r great sir......Keep it up sir.
@barrosvinicius4 жыл бұрын
Congratulations. Jajaja quiero hacer esto también viva la WiFi Free
@anthonyg46714 жыл бұрын
Clever, but you need to fix your clock :-)
@michaelc.2674 жыл бұрын
To Kreosan, I would like to invite you to Italy, Sicily to meet an Engineer friend of mine, I want to create some great devices to sell are you and your team available?
@johnhoye65843 жыл бұрын
I do not care if it works, this guy is awesome.
@anshukumarsingh953 жыл бұрын
I have came here after watching you guys on hacker om channel. Your collaboration with hacker om was awesome.
@dtesta4 жыл бұрын
Seriously, with that long cable, you would loose all the gain you might get from the antenna. I smell fake. When you make these kind of USB-adapter-type antennas, you should use a long USB-cable and attach the adapter directly to the antenna itself, to get the shortest possible antenna cable.
@DavidLopez-bz4rj4 жыл бұрын
Yes, it is a great fake. The antenna cant work at all. They lack of basic knowledge of antennas.
@craigwall95364 жыл бұрын
@@DavidLopez-bz4rj Apparently you're ignorant of disc-on-rod wave guides. This isn't fake. Put another way, this is a Yagi with circular polarization. It is _you_ who are ignorant of antenna knowledge.
@craigwall95364 жыл бұрын
Silly you. They've left the cable long because it would be stupid to cut it until you decide where you want to INSTALL it. AND because if it works at all, they know that it will ONLY GET BETTER when the shorten the coax. They're EXPERIMENTING. They aren't stupid and you haven't told them anything they didn't already know.
@DavidLopez-bz4rj4 жыл бұрын
@@craigwall9536 You are the one who doesnt know that circular pol has a penalty of 3db versus linear pol, so silly is using it for wifi. I am a ham radio operator and I use a homemade antennas since 25 years. I can reach my home with my smartphone from 2km away, I have internet all around my valley. This antenna design is old as hell, you will never see a yagi design with evenly spaced elements. It is a piece of shit, I reach more with my microwave oven hahah
@artemikf4 жыл бұрын
Когда на основной канал выйдет ролик про чернобыль
@peppapigofficialspoiler12904 жыл бұрын
когда сделает у себя квартиру похожую на чернобыльскую
@great-27Ай бұрын
To get a better signal, I advise you to use copper for everything, including the pole. Also, the longer the cable, the weaker the signal. Therefore, if you do not need a cable with a length of 60 meters, then take what suits you, and the maximum is 100 meters.
@curiositek2 жыл бұрын
Hello, excellent work, what router model did you use?
@BurkenProductions4 жыл бұрын
What?? The ground is shorted to the antenna ??? How could that work
@lordelectron65914 жыл бұрын
Maybe he insulated the discs?
@lordelectron65914 жыл бұрын
@@lands1459 Wait that means we get wireless free energy?
@lordelectron65914 жыл бұрын
@@lands1459 Can these rf signal be converted to dc? BTW thank you
@vitcenek86114 жыл бұрын
Most of your projects are great, but this is fake as hell... Please avoid that, it did not makes a good name of your chanell.
@craigwall95364 жыл бұрын
It's not fake. This WWII technology, just at shorter wavelengths.
@niklaswallin947810 ай бұрын
always with the coolest cars!!!
@furonwarrior4 жыл бұрын
Would of advice, TV coax uses 75 ohms. 50 ohm coax works better.
@pauldelasco3 жыл бұрын
This channel and these fellas are great! What knowledge and fun! They are smart. Fun guys who are very entertaining and funny. Great humor guys!!! We love your content here in 🇺🇸 🌎 🇷🇺 USA!! Please continue the great videos. 👍
@xxEmeSiSxx4 жыл бұрын
would this work the same way with a yagi high gain antenna? with the usb wifi adatper?
@cubanelabs85734 жыл бұрын
i bet all of the students on youtube are right now building this
@z3r0sz593 жыл бұрын
KREOSA Sou Do Brasil.. your videos are very good, the experiments or experience as I say, the antenna is very good. Would you manage to make an omni antenna 15Dbi or above 10Dbi ???
@hubzcaps3 жыл бұрын
More rf expiriments like thiss. Please
@emilianorosso11133 жыл бұрын
Hi, I have a problem... Since I use a 0.5 mm thick sheet for 20 discs that's 10 mm. I would like to know if the distances you give represent the internal step or if I have to take into account the thickness of the sheet. Thank you!
@gamazdaisgreat13912 жыл бұрын
Internal
@windesyard63003 жыл бұрын
What is the name of the connector that you use? From the satelite cable to wifi adapter?
@Chuggiek4 жыл бұрын
Sure i can pick up open networks with my own router.
@kellermatyas71004 жыл бұрын
How cool that ZAZ 965 :)
@gianpierverutti64433 жыл бұрын
Have you tried using a UTP cable ?... would have less cable atenuation
@steampunkfox14112 ай бұрын
One thing I am hitting a snag on: My cable had a totally different end so i cut it off to get at the tip.... does the thin wire in the middle have to touch BOTH the first two plates or just the second?
@MAN0202VAN4 жыл бұрын
This booster can be use for mobile network or to send signal?
@drz40732 жыл бұрын
Finally a use for soup can lids
@philmichael1434 жыл бұрын
Love this channel
@FREEBLISS503 жыл бұрын
Thank you! Well done!
@steviebboy694 жыл бұрын
Nothing like getting free wifi if you dont have or cant afford the internet. What sort of car was that, the motor at the end looked like a VW Bug engine. nice little car reminded me of the Leyland Mini Clubman I once had.,