Nice work! I have refitted a Federal JetStrobe housing with all LED modules, they are dual color, one row amber the other row blue. Takedowns and alleys are standard high output MR16 LED spots at 12v and 6000°K for a blue white light. Since there is plenty of room within the housing as to height I have incorporated a third row of amber lights to the rear for use with a Federal Signalmaster. The interface to control the main light bar is something I built based on a PIC micro controller similar to what was used in the early Smith & Wesson 911 light bars. The plus is that it doesn't have the problem of scrambled memory like the old Smith units. I have incorporated transient protection on all of the IO lines. Love recycling and up cycling older equipment. I find that the older FS Jet series light bars do not create a lot of wind noise as some of the newer blunt nosed thin bars. Yeah they are not as stealthy but without the old color lenses and clear LED's one doesn't quite know the color of the bar until its activated and yes there is a sequence one must go through to get it into Blue mode and a dual use switch brings it back to amber. This was a proof of concept bar for an agency that does mainly undercover investigative work.
@fedsigMaster11 жыл бұрын
I did this same upgrade 2 days ago. I'm glad to see that I did it the same way you guys did.
@NatureGuy36011 жыл бұрын
I enjoy this new series of "how to" videos! Keep up the good work.
@TheLegendaryPaul11 жыл бұрын
Very nice Video!
@SkittleKicksPlays10 ай бұрын
I've never really figured out why they still use aluminum or steel frames for full size lightbars. Weight means reinforcement of the roof, added weight can use more fuel, and then there's shipping costs. So why haven't manufacturers switched to a poly framework?
@mred41911 жыл бұрын
Thank you for the video, I have been in contact with Whelen engineering about upgrading my liberty Lightbar and they told me it could not be performed because it would cost me too much. I would be better off to buy a new one from them, I would really like to find out if I can upgrade my lightbar?
@thibodeauxpaul64292 жыл бұрын
Is there a part number or link for the LED Takedown lights please?
@raywilhelm4456 Жыл бұрын
Also looking for these
@FDNY63truck11 жыл бұрын
oh ok thanks!
@arielb_ve4 жыл бұрын
Hey I need some help I just picked up a used NJ Passaic county Dodge Durango with this light bar attached to it and I wanna upgrade the halogen seach lights and alley lights to led your video was very informative of helping me disassemble it but I don't know where to get the parts
@SIRENNET4 жыл бұрын
Here's a link that'll take you right to them :) sirennet.com/lightbars/lightbar-parts.html
@joshuacaseltine11433 жыл бұрын
What would be the part number on the takedowns you installed...
@anotherbluenova6358Ай бұрын
I want to know how to make my red and blues to all white.. Civilian application
@SIRENNETАй бұрын
If you have a DUO color lightbar with White secondary color, it's just a matter of reprograming. Otherwise, you will need to remove the Red and Blue modules and replace them with White. eBay, elightbars.org, and other third-party sources would be the best places to look. The light-heads for first-generation Liberty lightbars have been discontinued by Whelen Engineering.
@91steelblue3 жыл бұрын
I have a loaded lightbar (14 amber LED modules). Can I buy 2 more amber LED modules from you & swap out the 2 halogen takedown lights or is there no more plug-ins for more LED modules? Thanks.
@PoliceforChrist3 жыл бұрын
I wonder, if you could pull the halogen bulb out and replace with an LED bulb from auto parts store without buying a kit?
@VVK5W2 жыл бұрын
So the LED alley lights are held in place by the top, not secured by fasteners like the old halogens? I'm getting ready to retrofit one of these bars myself.
@SIRENNET2 жыл бұрын
The Alley Light Brackets are held in place by the top and the Base. There's a great look at how they secure if you pause at 12:59.
@timothyquilty44354 жыл бұрын
Does the L/C I/O Board acc harness work on the the wecan i/o board
@SIRENNET4 жыл бұрын
With the WeCan bar using the software for programming modules there's no need for it.
@fawnz1411 жыл бұрын
You should show a video of them working!!! It gets annoying when you show or build things and don't end up showing them on.
@matthewknowles71435 жыл бұрын
Yeah, I'm gonna bring this one back from the dead... Now, I'm working on rebuilding a Liberty and converting it to WeCan. When I got it, it wasn't in the best condition (still isn't), but I'm going to be converting the takedowns to LED. With the LR11 alley mounts, do I need standard or extended length LIN12 corner modules? I feel like standard would leave room for alleys and extended would be the option if the bar didn't have alleys. Is that correct? First solo rebuild, plenty of experience with emergency lighting, but mostly UC/unmarked installations, so no lightbars. Thanks for any insight!
@SIRENNET5 жыл бұрын
With the switch over to LR11 alleys, you can use the extended 12 diode corners... they fit perfectly and just enough space for the LR11's. Or you can indeed stick with the shorter corners.
@matthewknowles71435 жыл бұрын
SIRENNET What's the difference between the two? Will there be a gap between the light heads if I use the standard length corners?
@SIRENNET5 жыл бұрын
The short corners will have a gap of about 1.25" on each side. If you can, the 12 diode extended corners would be a nice upgrade for side visibility :)
@matthewknowles71435 жыл бұрын
SIRENNET You guys are lifesavers! Always quick on the draw with all of the answers. Thanks so much!
@SIRENNET5 жыл бұрын
Glad we could help :)
@chrishatfield97906 жыл бұрын
Will the wecan module work with this type of liberty bar?
@SIRENNET6 жыл бұрын
It won't. You'd need to use it with an SW series.
@FDNY63truck11 жыл бұрын
were did you get the posters in the background
@Sassquatch7134 ай бұрын
Where can you get the harness?
@SIRENNET4 ай бұрын
The harness is no longer available from Whelen Engineering, and we don't have any left in stock, unfortunately. Best places to search this out are eBay and elightbars.org.
@GrandmaKeith8 жыл бұрын
I am in the process of rebuilding an old Edge lightbar and converting it into an all LED Freedom bar. I am currently looking for a Freedom Power Supply to begin with.
@SIRENNET8 жыл бұрын
+JAGExecutiveServicesInc You would actually need a Freedom Bar I/O Board if your doing an LED conversion. Also, there are different I/O Boards- The are WeCan control-Boards and standard low-current switching control-boards.
@GrandmaKeith8 жыл бұрын
+SIRENNET So I could actually use the WeCan I/O board with regular 400 series led modules.
@SIRENNET8 жыл бұрын
+JAGExecutiveServicesInc If you're going to use a WeCan I/O Board, then you would most definitely want to use the 6 over 6 400 series Module's.
@GrandmaKeith8 жыл бұрын
+SIRENNET You wouldn't happen to know the part number for the i/O board would you.
@SIRENNET8 жыл бұрын
+JAGExecutiveServicesInc Unfortunately not. We'd suggest that you contact Whelen Engineering for the WeCan parts information. They can be reached at- (800) 294-3536. Thank You.
@m00nraker454510 жыл бұрын
how does stewart like his land rover hes sitting in there?? :D
@SIRENNET10 жыл бұрын
It's a fun Rig. We just make sure he keeps the snacks out of it :)
@SIRENNET11 жыл бұрын
They are actually blow-ups based on photos taken by Stuart from his travels.
@HenriBeaudoin8 жыл бұрын
Hi, I just purchased a WeCan I/O Upgrade board for my Liberty bar. Does this board allow me to run duo lightheads inside the bar? Thanks!
@SIRENNET8 жыл бұрын
+Henri Beaudoin The Part Number of the I/O Board would help determine what it is set up to run. Could you please tell us the long digit Part umber on the Board itself? You could also check this with Whelen Engineering if you'd prefer.
@HenriBeaudoin8 жыл бұрын
+SIRENNET 0264940 Thank you for the help!!
@SIRENNET8 жыл бұрын
+Henri Beaudoin Is there a number set anywhere that starts with: 01-,02,46-,68- ? The Part Numbers are usually 10-12 numbers long.
@HenriBeaudoin8 жыл бұрын
+SIRENNET 01-0264940-00G
@SIRENNET8 жыл бұрын
+Henri Beaudoin That I/O Board is for a Solo Liberty Light-bar. The DUO version uses a different Board and internal wiring harness.
@SIRENNET11 жыл бұрын
If you have the "New" end-caps, that do not have the Alley window, you can still successfully install the SPALF1 LR11 Kit. The only end-cap in the Liberty family that will not work is the end-cap option that had both an MR11 alley and TIR3 Light-head mounted to it. You would have to fully remove that part to add the LR11 Kit.
@GrandmaKeith8 жыл бұрын
I'm looking to convert a Whelen Patriot lightbar to a newer Liberty lightbar.
@SIRENNET8 жыл бұрын
It's a bit of a process and a lot of new Parts, but it can be done. You may want to consider a new Liberty II platform as it was a lot of great and new benefits.
@GrandmaKeith8 жыл бұрын
+SIRENNET I've already upgraded the takedowns and alleys from halogen to new LR11s. The Patriot lightbar came with a 6 Head LED TA when i bought it online.
@GrandmaKeith8 жыл бұрын
+SIRENNET My takedown and alleys are LR11s. I was wondering how to activate the flashing option.
@SIRENNET8 жыл бұрын
On the trigger wire Harness, there will be a wire dedicated to Flashing the TD's and Alley's. Try powering up the White w/Blue wire.
@jbent51248 жыл бұрын
how much is that kit?
@SIRENNET8 жыл бұрын
+Jeff Bent Good Morning :) If you could please email our Sales Team or give us a call, we'll be glad to assist you with Pricing. We can be reached at- (888) 959-0911 or info@sirennet.com.