Rebuilding a 1977 Suzuki GS550, Part 1 (The Tear Down)

[@Jayztips]

Thanks i have a 1979 GS550E, i have just started working on.

[@cwrighta70]

Awesome and meticulous work. Looking forward to part 2!

[@Kollar0718]

At least someone with a worse engine than mine... :D Last year I bought a modified 1978 GS500 with the GS550 top end and carbs - still working on it. :)

[@gamingtech3736]

Man i also got a 500, people barely seem to know about them. Beleive i have upgraded carbs (the ones in this build) but they're a bit leaky, really weird behaviour. How's the progress after 4 years? Things i should keep in mind?

[@donphillips7671]

Thanks for posting that video. I just bought a '81 GS550 which isn't running. I am looking forward to doing what you are doing. Please keep the videos coming, cause I am new at this as well.

[@dsheridan1732]

Awesome video, only wish there were more parts to this series!

[@strokedyamaha3746]

Brass wire wheels are great but if you want to remove that carbon real quick just use some chem dip and let it sit and it will come right off. Also, if you want to get the exterior metal real clean, use some ospho mixed with distilled water 50/50 and let it sit for a few and scrub with a stainless brush👍

[@telabib]

well done.

[@thorntonbaker4321]

got any parts!!

[@malcolmmichaels378]

I.s.o. carbs or ideas for alternate carbs.

[@henar86]

hello! I need to know where I can get pictures or repair Brico gearbox

[@asnack]

I have a 1982 GS 850 with a hole in the oil pan. Can this be fixed. I don't think jb weld is gonna do it.

[@pCneter]

how do you remove the timing chain on the head and putt it back on timing ??

[@Drop.a.gear.disappear]

Nice bike, what bike is the front end of?

[@MrM1ltron]

Hey man nice video! Got the same bike, 77 gs550 but one of the carburetors seem to give out! The #1st one to e exact.. Is there any thing possible to do in order to get it working(the rest are good), or is it better to buy new ones? Pls appreciate any feedback!

[@hotshotfire1]

Do you have a site for any or all the parts im trying to rebuild a 1978 gs100. Any site will help

[@victorperezyproo6557]

Perdón por molestar, ¿Como se mide el aceite a la suzuki 550cc, y que numero se le pone, y si se pone quitando el tapon que tiene del lado derecho. gracias

[@danielclift1]

what song is that at the beginning ?

[@isjones2112]

I found a barn bike that was sitting for years but was complete. Don't know how long since it ran. Bike had 5600 miles on it should I rebuild it or try and get it to run? Its out of the bike right now so I can really test it. Any info is appreciated.

[@ramsn1971]

Any engine needs 4 things to start and run: compression, air, gas and spark. What I would do is: 1) test for compression 2) test for spark 3) clean the carburetors 4) get her started. Last, after you get her running check for any air leaks.

[@isjones2112]

Thank you for your reply. I came upon another question I was hoping you could answer. IS there a place to get rear swing arm bearing for a 1981 Suzuki GS650G? I cant find anything online.

[@ramsn1971]

@@isjones2112 I was able to replace mine. You may want to also look for bearings for the GS650 or even the GS750. Sometimes it's the same bearing. However, before doing so make sure you compare if they truly are the same by looking at the part number. Google "suzuki parts house" and start from there.

[@ianjones5872]

Thanks for the info! I have brake question. I took the rear brake apart and the pistons were stuck in the caliper. I got them out and cleaned it all up. There is a very small piece of rust on the piston. Do you think I should replace the pistons or can I do just the seals

[@ramsn1971]

@@ianjones5872 if it is surface rust you can scrape off the rust with 500 sand paper. use 1200 at the end to smooth it out. if the rust is very deep and is causing pits then you'll need a newer piston.

[@ryanmaxerasmus4608]

Hi does anyone have the torque specs for the motor? Would be much appreciated.

[@clockerification]

Is that the same bike at the end of the video?

[@AmericanDefender]

How did the eBay gaskets work out for you?

[@victorperezyproo6557]

Hace un mes te suplique, me enseñaras, todo lo relacionado con el aceite:¡ Como se cambia, como se mide, que numero de aceite lleva, y por donde se le pone???Esta en el comentario de abajo, Compre Suzuki 550cc 1980 y no se hacer eso. Gracias y perdón por molestar, pero si no aprendemos de los que saben, tendríamos conocimientos, equivocados. Gracias mil

[@henar86]

si te enterás avisáme!!!! saludos!!

[@johnkinnane547]

G'day mate you are doing a very good job, that engine is really looking like new. Well done regards John Tasmania Australia. PS is the head straight and not warped, does it need machining?

[@aaronlee8845]

Can you plz help shed some light on the problem I'm facing with my motor? There's a strange noise coming from my engine. Video's at 'Noise - suzuki gs550'

[@SuperWatson63]

I have a 1980 gs550l

[@victorperezyproo6557]

Con todo el respeto que merece usted, le digo. Ya para qué me contesta??? Si tiene un año que le hice la pregunta?? Pero aún así gracias.

[@victorperezyproo6557]

No contestas a los que hablan español, verdad?????

[@ramsn1971]

Si contesto, dime...

[@Extremanaturaleza]

victor, yo voy hablar con propiedad, por que tuve una igual del año 1980. terrible caño..la tuve 4 años y aceite siempre le puse Castrol 20 w 50. saludos!!!!