This video helped tremendously. I would have never had known to do these adjustments. THANK YOU, THANK YOU, THANK YOU.
@soy1de3aztlan Жыл бұрын
You wellcome I’m glad it helped you out 😎👍🏼
@thegutlessbellydragger26 күн бұрын
Thank you for this.
@soy1de3aztlan26 күн бұрын
Any time bro 😎
@TW399 ай бұрын
Hi is it the speed and torque of the servo that makes it hop
@soy1de3aztlan9 ай бұрын
That together but also adding weight to the back and doing a few mods to the front nose of the chassis at the same time will have to add a BEC set at 8.4 volt if the servos can handle it ,3s lipo battery to give the servos more full power !!!
@TW399 ай бұрын
@@soy1de3aztlan does the motor in the Servo have to be brushless motor
@soy1de3aztlan9 ай бұрын
@@TW39yes !! There’s two that are the most useful/powerful the reefs 300s and the jevries super pump !!
@TW399 ай бұрын
@@soy1de3aztlan can I use a 30kg dc4.8-6.8v dsservo digital brushless servo the torque is 29kg.cm@5v 34.5kg.cm@6.8v speed is 0.2sec/60@5v 0.17sec/60@6.8v for hoping
@soy1de3aztlan9 ай бұрын
@@TW39 yes you can but it’s not going to give you much power to hop high ,now remember you still goin to need a bec set up at 6.8 volts to get the most power out the servo also you going to need a lipo battery!!
@AndrewAvila-p7k11 ай бұрын
Hey brotha, What exact tool do we use to swap out the steering servo?
@soy1de3aztlan11 ай бұрын
Used a hex screw size 2.0mm
@dopenvyyify2 жыл бұрын
Thank you broth much appreciated!!! Straight up and easy with it thank you!
@soy1de3aztlan2 жыл бұрын
You wellcome homie 😎👌🏻👍🏼
@dopenvyyify2 жыл бұрын
@@soy1de3aztlan what do you have your mixes set at?
@soy1de3aztlan2 жыл бұрын
@@dopenvyyify for the end points?
@soy1de3aztlan2 жыл бұрын
@@dopenvyyify cuz on the mixes settings I left it alone I didn’t mess with that
@dopenvyyify2 жыл бұрын
@@soy1de3aztlan my whole remote got factory reset so everything is thrown off and not working the same I fixed my end points cause your video but all of my mixes are turned off and I don't think that's right
@lambo48511 ай бұрын
Thx for the tips 👍🙏….I listen to doo wop too working on the RC lows 😎
@soy1de3aztlan11 ай бұрын
You wellcome bro 😎👍🏼 nothing but em doo wops will working they so relaxing 😎😁
@reneherreea914711 ай бұрын
I have the same issue with the frame showing on one side of my gold digger. One side sits flush the other side shows the bottom gold frame. I also noticed that when i raise the rear, one side goes a tad bit higher than the other side. I might have to mess with the end point settings just a bit.
@soy1de3aztlan11 ай бұрын
Yes if it’s not level right from the back is going to be the end points!! What I be doing on mines I kinda of eyeball it or better I get a small level n lay it flat on the back on the chassis with the back all the way up n I drop it all the way down to get a perfect level 😎👍🏼
@reneherreea914711 ай бұрын
Ill give it a try when i get back home. What did you do about the frame being twisted on thebottom where the sides are at?
@soy1de3aztlan11 ай бұрын
@@reneherreea9147 I did change the frame the “chassis “ I got the one all chrome so that fix the issue !!
@fluffycakes527 Жыл бұрын
G do you have a video on how to install the servos on the Monte Carlo?
@soy1de3aztlan Жыл бұрын
Was up homie 😎I do have but not really detailed on how but check out this channel the homeboy those have lots of helpful videos and he explains more details youtube.com/@NorthSideCustomRC?si=5wy5mvJL1hBE3xdO
@fluffycakes527 Жыл бұрын
@@soy1de3aztlan Orale G much appreciated 🙏
@soy1de3aztlan Жыл бұрын
@@fluffycakes527 no worries homie any time 😎👍🏼
@fluffycakes527 Жыл бұрын
@@soy1de3aztlan Ma boy you know why my Monte Carlo is acting on its own? Almost like it’s possessed. My controller started beeping and now it won’t move, not even fixing the endpoints works
@soy1de3aztlan Жыл бұрын
@@fluffycakes527 it sounds like you have to bind your romete control with your RC transmitter, I guess some how it got disconnected when that happens the red light starts flashing but the car don’t move at all !!! Al you have to do it bind your RC transmitter with your remote control homie n you be go to start havin fun with it
@adamwaselich7315 Жыл бұрын
I'm setting up my radio for the first time tomorrow. Any advice?
@soy1de3aztlan Жыл бұрын
Yes the ones I got on mines are going to be different as the rest of the others !!! It depends on how your settings numbers are in your remote control also on the servos !! It depends on what settings you want to change or if you want to mess with your servo settings to make it higher or lower,or on the speed if you want it to not drive to fast !!!
Check out he’s videos he explains more on details 👍🏼
@shadowbird2 жыл бұрын
Good video.Thanks. even when my 64 is flat. It’s like I don’t have much steering trim. I try to set it but it does not change much. What channel is it on the controller? Thank you have a good day!
@soy1de3aztlan2 жыл бұрын
Thank you bro 😎 👍🏼!!! That will be channel #1 Olso you can try the subtrim on your control you will fin it where I show I’m looking for the end points it’s going to say subtrim also is the first top line it has a small arrow!!
@cigano21capoeira94 Жыл бұрын
How do you save your new endpoints on the remote?
@soy1de3aztlan Жыл бұрын
After you get all your end point right on your remote control look for the bottom that’s it says cancel/save is right under the menu/enter button!!! An just press on it a few seconds and that’s all you have to do after pressing it for a few seconds they will be saved up homie 😎👍🏼
@cigano21capoeira94 Жыл бұрын
Thank you very much this was really helpful I already had to replace a few parts cause it keeps breaking lol 😂
@soy1de3aztlan Жыл бұрын
@@cigano21capoeira94 you wellcome bro 😎👍🏼I feel you on that it happen to me at first too but after a while stared learning more n more 😁
@jersonmendoza20942 жыл бұрын
Monte Carlos are cool thee only problem with them is the steering..after a while I sold mines for that reason it was a Hopper also had it customized sold it for $1500
@soy1de3aztlan2 жыл бұрын
That was a good price not bad at all 👌🏻😎!!! Yea I guess there was many montes with bad steering servos !!!
@jersonmendoza20942 жыл бұрын
@@soy1de3aztlan Simon my boy
@jerrydoublej22362 жыл бұрын
Good info carnal. Gracias... Wish there was a setting to be able to have the ride drop fast like when you open up the dumps on a real hydraulic set up.....
@soy1de3aztlan2 жыл бұрын
Óralezz de nada carnal 😎👍🏼!!! I know it would had been real nice I think the only way is to replace the stock servos for reef’s or some similar to reefs they more faster an powerful but is like buying other 79 Monte 😰
@sammygonzalez7627 Жыл бұрын
Install a BEC 10amp for 8.4 voltage on the servos, for better hopping
@soy1de3aztlan Жыл бұрын
That’s cool it gives they servos more power 👌🏻😎did you also upgrade the servos ?
@soy1de3aztlan Жыл бұрын
I did upgrade all 4 servos now I got it to hop an dance faster !!!
@sloanesnydet Жыл бұрын
brotha you saved me! hands down!
@soy1de3aztlan Жыл бұрын
I’m glad it help you out bro 😎👍🏼
@sloanesnydet Жыл бұрын
@@soy1de3aztlan helped me out alot but now i got problems with right side going up and after adjusting stuff nothings helping ill make a vid if udk what im talking about
@soy1de3aztlan Жыл бұрын
@@sloanesnydet I do think what are you talking about !! Check on here a channel call “NorthSideCustomRC”he uploaded a video not that long ago with more better explanation on how to set up the end points brother 😎
@Looneyboy805Ай бұрын
Dion and the Belmonts teenager in love in the background firme rola oh and also what does CH 4 does
@soy1de3aztlanАй бұрын
@@Looneyboy805 that’s right homie nothing but em firme oldies 😎the ch 4 is to control the right front wheel sence the 79 monte has 4 channels an 4 servos each channel controls each servo for the 2 up front an 2 on back !!!!
@meefthepotatoe43632 жыл бұрын
I’ve only used my Monte once on the night I opened it for about an hour i didn’t even charge it, I just powered it up straight out the box 😳 I hope I don’t run into that steering issue like I’ve been seeing a lot of on utube 😰 that would suck ……. Luckily if I do I’m gonna save this video n use it as a fix 👍 ….. 🤔 redcat should make you their IT rep. 😎 n break you off a lil pocket change or hit you will a lil discounts on redcat accessories 👍😛
@soy1de3aztlan2 жыл бұрын
Hell yea right on 😃shoot em don’t care 😏not even to get a discount on parts 😰😂😂!!! Is all good ain’t tripping at list I’m glad I’m able to help out for all of uss who are in to this 😎👍🏼
@jesusmata9565 Жыл бұрын
Manufactor error, i saw your post before, and when i got mine same thing,
@soy1de3aztlan Жыл бұрын
Yea there where a big bunch of em servos that came out bad from the manufacture!! I did got a replacement for the same one but I just got my self a better one from reef’s but I did had to spend more money though lol !!!
@Justsomecarlover6 ай бұрын
I need help with mine i have the same thing i reset it and now it aint working
@Roboli-nr1mv Жыл бұрын
homie smh😂
@soy1de3aztlan Жыл бұрын
😁😎👍🏼
@michaelvita82 жыл бұрын
I used ur end points and man sets lower I like the set up
@soy1de3aztlan2 жыл бұрын
Thanks bro 😎 in glad it helped you out 👍🏼
@josetrujillo60812 жыл бұрын
Thanks I don’t know what I pressed and broke one of my shocks goin to try your endpoints tomorrow also my switch that rises the front only lifts of one side
@michaelvita82 жыл бұрын
Undo ur shocks before you adjust ur end points or they can be over stretched brake shock I didn't do that then when I replaced shock my servo starterd to smoke burned it up I learned the hard way with my car right out the box steering stopped reset my end points broke shocks burned up servos once I figured it out I love this car
@soy1de3aztlan2 жыл бұрын
@@michaelvita8 yea of you don’t set the endpoints right the motor will burn out because it’s under pressure an still trying to push on the shock !!!
@soy1de3aztlan2 жыл бұрын
@@josetrujillo6081 try out what Michael vira posted!!! It really depends on how ever car has the endpoints set up !!! Un plug all your servos an do one at the time , make sure that the motor it’s not under pressure if you heard like a grinding sounds stop an start allover again when it makes that wierd noise it means it’s not set up properly it might burn also make sure when you hook the servo horn see that it doesn’t go all the way up or all the way down ,when you lift the car the servo horns should be on a 90degre or straight down !!!
@LordDecrepido9 ай бұрын
😂😂😂eh short video but u talked Hella slow this could been like 8mins hahahha
@soy1de3aztlan9 ай бұрын
😓🤣🤣yea I know it was some of the 1st videos I made I was new to all this 😓also when I make the videos I don’t edit em or nothing I just make em n upload em but I’m still learning how to making better n try not to make em so long 😎😆😆