Remote Lock Installed!

[@doggie1luv]

Teddy coming through again with the video of knowledge!!! Thanks Bro!!

[@Teddy_B_Ridn]

🙏🏾

[@stefansgarage3014]

Thanks buddy, I just ordered my chopped Tour Pack and I'm glad, that I found Your video. Very helpful!

[@hammmernnails1504]

Nice write up. Thx

[@Teddy_B_Ridn]

I appreciate that. Thanks for watching.. ✌🏾

[@ChuckBurt-c7b]

very informative, do you have a appoximent cost of the project? thanks

[@Teddy_B_Ridn]

Hey whats up! With all the parts and materials I listed in the description, it was less than $200. Thanks for watching!✌🏾

[@floydbranham4575]

Sweet! Thanks for the knowledge

[@Teddy_B_Ridn]

I appreciate that… ✌🏾

[@climbercox87]

Awesome video! Good clean work. Another example of HD not being very informative of what bikes products work with or not. Looks dope though

[@Teddy_B_Ridn]

I appreciate that! Thanks for watching! 👊🏾✌🏾

[@brianjohnson3444]

Solid work and good info bruh! I have a 2019 Street Glide CVO with a king tourpak and have been wanting this for it. Now I know how to do it. Thanks!

[@Teddy_B_Ridn]

Hey man, I appreciate that and thanks for watching! 👊🏾✌🏾

[@brianjohnson3444]

@@Teddy_B_Ridn Quick question...Do you remember the color of the two wires you tapped into for power to the actuator?

[@Teddy_B_Ridn]

Hey what’s up! Been super busy. So I choose the right saddlebag wire harness to tap in to. I followed the two wires that came from the actuator under the lid to where it goes in the larger wire harness on the inside of the saddlebag. Then I found which wires it connected to when the other harness was connected on the outside of the bag. Now for some reason the connecting wires, the ones I needed, in the outer harness were a different color than the ones coming from the actuator on the lid so I just made sure I followed the pin spacing. The two wires I taped into on the outer harness for me was the two peach colored wires. One with an orange stipe on it and the other with a red stipe on it. Sorry for being so long winded but I wanted to try to be a clear as possible. Hope this helps… 👊🏾✌🏾

[@brianjohnson3444]

@Teddy_B_Ridn No doubt bruh. I appreciate the detailed information. I just ordered the parts three days ago. Thanks again!

[@randybard224]

Ok I didn’t know you could do that thanks

[@Teddy_B_Ridn]

Hey what’s up! It took me some time to figure it out but it’s so much better now… Thanks for watching!✌🏾

[@jaypee6495]

I have a 2011 CVO with automatic locks. I'm changing my tour pak to 2014 model. I wonder if a wire harness could be made from my saddlebags too?

[@Teddy_B_Ridn]

Hey what’s up! I couldn’t see why not but unfortunately I can’t say for certain.

[@Wilsey523]

I love it. I have the same bike. What’s the hitch that you have to open and close your tour pack?

[@Teddy_B_Ridn]

It’s the Ultra Brace. I did a video on it. Thanks for watching!✌🏾

[@etontheground-ETOTG]

Great video

[@Teddy_B_Ridn]

Thanks! I appreciate that…✌🏾

[@jeffwilliams716]

Great looking bike! *New Sub* too!

[@ChrisGlides]

Nice 👍🏾

[@randybard224]

Were you able to keep the same key for both the tour pak and your saddlebags

[@Teddy_B_Ridn]

Hey what’s up! When ordered the new tumbler from HD I made sure it matched my original key. Thanks for watching! ✌🏾

[@elliot1300]

Nice looking bike. What size bars do you have? Thanks

[@Teddy_B_Ridn]

Hey what’s up and thanks for watching… I have the 10” fused low handlebar’s for the RG from HD… ✌🏾

[@RanGer-498]

What wires did you connect to exactly? and what did you trim at the actuator exactly.? Thxs

[@Teddy_B_Ridn]

Hey what up 👋🏾… I trimmed the actuator housing plastic cover and backing just below the circuit board inside of it, giving me just enough to clear the curved area of the tour pack wall. As far as the wiring, I followed the wires coming from the saddlebag actuator to the wire harness in the rear wheel well and tapped into those… Hope that helps… ✌🏾

[@RanGer-498]

@@Teddy_B_Ridn thxs

[@frankjay482]

Sweet Bike Boss

[@Teddy_B_Ridn]

Thanks… I appreciate that! ✌🏾

[@dalegribble7630]

how can I do that to my saddle bags? my locks keep breaking

[@Teddy_B_Ridn]

Hey what’s up. I’m not sure what u mean when u say “ur locks keep breaking”…

[@kellybgliding]

Nice job bro and a nice looking bike. I’m subscribed

[@Teddy_B_Ridn]

Hey what’s up… thanks for subscribing I appreciate that.. been a sub of urs for a while and KONG is looking like a BEAST!!! ✌🏾

[@kellybgliding]

@@Teddy_B_Ridn appreciate bro . We definitely have to support one another

[@Tumble96]

It should work on any bike With a touring pack

[@ryanr4181]

is you're tour pack a OEM tour pack or after market?

[@Teddy_B_Ridn]

Hey what’s up! It’s an aftermarket tourpack (TCMT) from Amazon… Great quality. No complaints here… 👊🏾✌🏾

[@mrchue1]

How long of a job was this on average once all parts are on hand?

[@Teddy_B_Ridn]

Hey what’s up, I’d say it took me about a few hours. It would’ve been an easier install with the king tour pak though.. 😂✌🏾

[@stephen6157]

👍🏿

[@manuelramirez17]

Part number please?

[@Teddy_B_Ridn]

Part numbers are in the description my friend. Thanks for watching ✌🏾

[@snakebite6511]

waste of money