Remove and replace valve seal ,pumping oil,tune up Kubota DH1101

[@TheDesertSailor]

Thank you for this video!!!!

[@tractorsmarinemechanic]

Thank you for watching.kindly share and subscribe

[@jhaymaraquino5350]

Boss Video kadin po ng transmission Gear replacement ng iseki 3510 .

[@tractorsmarinemechanic]

Kapag may pagkakataon sir.ggwin ko para sayo

[@janithsithum3201]

How to identify valve seals are bad ?(how to confirm cause to problem is valve seal or piston rings)

[@tractorsmarinemechanic]

You can see the oil at the exhaust port

[@JohnStardust]

Hi, im about to do this on my d850. Does the valve need to be stopped by the piston in order to remove the spring lock? If so will it cause damage? Thanks for all the videos :)

[@tractorsmarinemechanic]

Just put the piston on top and you can remove the retainer.

[@user-ep5rp1km4k]

Да обязательно,если это не сделать клапан упадет во внуторь..проврежней от этого не будет!

[@JohnStardust]

Thank you ​@@user-ep5rp1km4k

[@user-fm7su4uj2m]

👍👍👍👍👍👍

[@user-ui1gp6oh5i]

Ок

[@shhhhawk6053]

How do you know when the piston is top dead ceneter?

[@tractorsmarinemechanic]

kzbin.info/www/bejne/kGnMeJuFh8t2bZI

[@tractorsmarinemechanic]

Just watch my another video and if you don't understand just go back to the comment section and I try tell you how get to know the top dead center

[@shhhhawk6053]

Thank you! Your videos are awesome! I was wondering how to find top dead center with the rocker arm off and no timing mark. When changing valve stem seals so you dont drop a valve

[@tadaskabliukas2797]

For the D850 engine, what should be the valve clearance?

[@tractorsmarinemechanic]

Just apply .25

[@tadaskabliukas2797]

@@tractorsmarinemechanic 0,25mm ?

[@bobbyandaya7893]

Boss ilan ang valve clearance Ng Iseki 2210 intake/exhaust?thank you.

[@tractorsmarinemechanic]

Pareho .25mm Ang nilalagay ko

[@nicksolano8475]

Bos ung rubber lang ba Ang papalitan Jan pagsira na valve seal Akala ko sate yan

[@tractorsmarinemechanic]

Valve seal

[@user-vk4ll8rk2w]

Добрий день,скажіть будь ласка який зазор робите Ви на клапанах?Дякую

[@tractorsmarinemechanic]

0.25mm

[@ruwansampathsampath5797]

Sir lanka is

[@loriejeorgetucay9886]

Gud day..sir sa Kubota 2402 ano po valve clearance nya? salamat

[@tractorsmarinemechanic]

Pareho lang po d2..25

[@freddiepasitenggpawi6084]

Ilan po valve clearance nyan idol at parehas lang ba sa makina na 3D84-16A kumatsu

[@tractorsmarinemechanic]

.25 lang Ang inilagay ko.yong sayo pwd rin para walang gaanong knocking

[@freddiepasitenggpawi6084]

@@tractorsmarinemechanic salamat idol

[@roylanggam3111]

Sir tanung ko lang po .. Ilan ang oil capacity nang Mitsubishi 4dr5 at anung oil ang ginagamit sa ganyang makina ?

[@tractorsmarinemechanic]

May dipstick nmn po Yan sir sukatin nyo n lang po kc Hindi matandaan Kung Ilan Ang oil capacity nya.sae 40 Ang langis nya.

[@roylanggam3111]

Salamat po

[@maypoststorytime]

Boss bakit Yong rotor ng tractor ko mabagal umakyat ano po kaya problema,matagal po kasi umakyat Yong rotor noa

[@tractorsmarinemechanic]

Check mo sir Ang hydraulic oil at filter palitan kapag Ganon p rin pump n po Ang sira.saan po location nyo?

[@user-hh7vl8ve9s]

👍👍👍🛠️🚜🚀🇷🇺

[@sahko_merkylov]

Почему попадаєт вода в масло

[@tractorsmarinemechanic]

Model of your engine?

[@sahko_merkylov]

@@tractorsmarinemechanic d1102dt

[@user-of3vn8qg7m]

بكم

[@martinross9403]

Bad video doesn’t if tell you the measurements for the rocker and push rods.

[@tractorsmarinemechanic]

Salamat sa panunood.