Renault Clio 4 - Rear lights replacement | How to change side, brake, reverse, fog & turn lightbulbs

[@BbrosAuto]

If this video was helpful and saved you money and time, you can support us and keep us going by buying us a coffee here: www.buymeacoffee.com/bbrosauto Thank you for watching!

[@vstankovic5]

Svaka čast na trudu, sve ste lepo objasnili. Bravo momci!

[@BbrosAuto]

Hvala na gledanju!

[@pcd4788]

Thanks so much for this video - job done in 10 minutes . Be aware that my wifes 13 plate RHD Clio took a concerning amount of force to get the rear light off and it released towads the boot ( sliding sideways ,)NOT striaght out due to the locating pin .. watch that bit iof the video you'll see what I mean . . There was a risk of damaging the cable as it released quickly .Might be worthwhile to get a plastic pry tool in at the non boot end to move it off the pin being carefull not to scartch paint etc . But thats for next time..... But the big question is 'Why Renault? Why ???

[@sleekitwan]

Thank you so much for this. I have the Haynes (UK) manual somewhere, this is becoming an easier and more ‘visual’ way to find guidance on a particular, specific task though. I have the PREVIOUS version of this Clio mk4 I work on (my wife’s car), and although the rear light cluster is different, this helped a good deal…mainly this later one is a better design. On ours, a 2015 RHD version, the full lights are on the body not the hatch, and there are 3 plastic plugs emerge from the cluster black moulding that contacts/inserts into the bodywork. ISSUE is that I did this in a cold snap during February in the UK, and our colder days, hate plastic. The trick as I remembered after breaking one of the plastic plugs, is to have a bucket of hot soapy water, and pour it over the area you are dealing with. This treatment, if you do the work right afterward, made the driver side cluster literally come out in 5 seconds flat, after the screws/torx are removed on the clip-attached black plastic ‘L’ piece my wife’s car has. The passenger side, man I wrestled with that thing, and I have the plastic pry-bar kit, and I was gentle with it for a half-hour before I realised, this ain’t budging til I use what I KNOW to be too much force…so one plug or peg locating the cluster snapped. I put a small blob of grease on these locating pegs before reassembling, and that should be that. Much easier job, because I knew what lurked behind the plastic moulding more or less, after your vid. Not a lack of confidence, just you cannot proceed until you know what the bit you cannot see, looks like really. Thanks so much, my regards, and take care all. PS that warming of plastic, is an important thing, for many jobs, the classic is folding old-style manual mirrors back in, that have never been folded back in…pour a bucket of hot water over them and lube them with WD40 or spray grease afterward, and nothing will break even in winter. Many plastics undergo embrittlement with sunlight and oxidation ie age. What gives way happily at a balmy 24 degrees C, is a stubborn pig when down at 5 degrees C, and might well prefer to break/snap off lugs or pegs or locating pins instead, if they are plastic. I remembered the trick a bit late, do it first, if it’s cold, then you will do the job in a third the time!

[@BbrosAuto]

Thank you for watching our video and for sharing your experience. I'm sure your detailed advice will help many when they read them in the comments, so I'm gonna pin it to the top of the comment section. It is so hard to work on plastic in cold weather and we're gonna use your advice! Thanks again!

[@cutesalem394]

Спасибо огромное, завтра побегу за лампочкой и сражу наповал соседей своими познаниями в ремонте авто🤣🤣

[@BbrosAuto]

🤣 Thanks for watching!!

[@nicoladerosa4636]

Sostituzione avvenuta grazie per il suo tutorial

[@BbrosAuto]

Thanks for watching!

[@ianjackson6751]

well explained and in.english nice one 👍

[@BbrosAuto]

Glad you liked it. Thanks for watching!

[@DraataDraata]

Thanx alot

[@BbrosAuto]

Thanks for watching man!

[@fekawidjaja1235]

Thank you for clear specs

[@BbrosAuto]

Thank you for watching!

[@alenviskovic7026]

I just bought reverse drive lightbulb according to the manual, h21w, and when i opened where it is, the bulb's neck there is twice as smaller. I have a clio 2019 facelift

[@sarica5555]

Very informative, thanks guys

[@BbrosAuto]

Our pleasure!

[@שאוליכהן-ה4ת]

Thank you very much friend for the explanation. Do you know the type of lamp or its model?

[@BbrosAuto]

Hey, thanks for watching. Are you thinking about bulb types? They are written down in the description and in the beginning of the video.

[@denislovric7657]

Bin total begeistert👍👍

[@BbrosAuto]

Danke sehr

[@mertg.4933]

Thnx man... 🖐🖐

[@BbrosAuto]

Thank you for watching!

[@Snaakable]

Thanks!

[@BbrosAuto]

Thank you for your support!

[@DinoxBusiness]

Any chance you can makw a video cleaning the engine of this clio with pressure washer and soap and brushes?? Would really appriciate

[@BbrosAuto]

Hi, we don't have this car at hand at the moment, but thanks for the idea and for watching. We have something similar in mind for future videos.

[@jokeryus]

Can u explained for the stop lights on the door ?

[@joakimberg692]

I cant remove the light holder, its...not possible at all. :D I mean, it looks mega easy on the video (time 0:55) but, its impossible for me. No matter what direction I push they wont release.

[@BbrosAuto]

I believe you, it's not as easy as it looks in the video. Wiggle it up and down while pulling towards yourself. It needs some force to it, but at the same time you need to be careful not to brake or scratch something.

[@Tsepz]

Having this same issue with mine 😂🙈 it’s near impossible

[@Ale-kc7tk]

Same here. Can't get it out

[@wercik68]

Thank you for your help.

[@BbrosAuto]

Glad it helped

[@nerfminer1956]

Its really imposible to take the light out haha on the other side it took me lik 10 seconds and on the other one it wont comw out after 30 minutes

[@BbrosAuto]

Sometimes thos pins can be really stubborn. But, yeah it should be possible :)

[@janusznowicki2110]

Dokładnie. Trzeba wyrywać klosz dwoma rękami z całej siły. To jest chore. A na filmikach wychodzą same😆. Nie kłamcie. Choć ten film i tak jest najdokładniejszy z tych które widziałem.

[@athfinest9583]

Are Clio's 4 bulbs canbus?Front and rear

[@nicoladerosa4636]

Salve, vorrei collegare la striscia led cofano su anabbaglianti clio 4 2019 ma mi serve un suggerimento per sapere quali sono i fili positivi e negativi dei fari anabbaglianti clio 4 2019 grazie

[@MrBole1968]

Dobro odrađen video i uputstvo!

[@BbrosAuto]

Hvala!

[@florianfilip9430]

What color is the marshal thread ?

[@johnnybob1972]

Are there different torx tx20 screwdrivers, different sizes....does it matter?

[@BbrosAuto]

No, tx20 is the type and size.

[@bionikatomik9736]

Hi, do you know how to do the same but with. Ren Clio 4 RS Trophy? I have no idea and I'm trying to save a few ££ and I can't find anything related with this, if you coul help I would like to watch!

[@BbrosAuto]

Hi, sorry for the late reply. Never had Clio 4 RS Trophy on hands, but I would presume it is the same. Did you manage to do it in the meantime?

[@teionbrooks4020]

Does the front light have a side light ?

[@BbrosAuto]

Hi there. It depends on the model. For some, the daytime running lights are also the side lights.

[@loyalliontv6123]

My renault megane mk3 multifunction satnav switch doesn't work when I press buttons. How to fix? Thanks very much

[@BbrosAuto]

@Loyal Lion TV Sorry, we didn't have a problem like this so we can give you good advice.

[@loyalliontv6123]

@@BbrosAuto please can you help me thanks

[@loyalliontv6123]

@@BbrosAuto its 2011

[@BbrosAuto]

@Loyal Lion TV We would be happy to help you if we have any idea on how to fix this, but we don't. Every information and our personal experience we share with others. Did you try to find some information about this problem on Renault forums? Maybe there is some useful information regarding your problem.

[@lionsden4908]

Does anyone know how to remove the light? Just doing it like this doesn't work