Megane 2 sloppy gearbox leaver fix this works on ND0 gearbox found on megane 2 1.9dci, megane 225, megane r26, megane f1, but might work on others as well.
Пікірлер: 32
@optimaltuber5 жыл бұрын
Probao danas na mome meganu 2 1.6 16v.Menjac je sad kao iz fabrike!!! Hvala Milose
@kralg Жыл бұрын
I managed to survive more than 2 years with broken bushing with this trick. I had to push it back onto the sphere like 10 times during this time, and when it popped out selecting 5th and 6th gear became very difficult. I bought a complete used control box eventually, but it turned out I was sold a right-hand drive unit which was completely different, so I had to replace the bushing only. This is such a simple little part and I have not managed to find it as new. Replacing and disassembling the control box is not as painful as I initially believed, so I recommend doing it instead of living with this problem.
@EngineeringSiblings Жыл бұрын
For me, it didn't pop of for a long time, when it did the second time I made a sleeve that I pressed in. there was nothing to "pop" anymore :)
@NikoPleva6 жыл бұрын
I´ve tried this solution today on Megane 2 CC 2.0 - works amazing. Like a new! Thank you
@linxus18 Жыл бұрын
I drilled little bit too high and only had access to upper part of the white bearing but I could press it in and it worked like a charm! Thank you!
@EngineeringSiblings Жыл бұрын
Glad I could help :)
@loremipsumdolor14443 жыл бұрын
Thank you!
@andreramos9455 жыл бұрын
Thanks Milos
@adamwhitaker95792 жыл бұрын
I’m just trying to work out if this is my issue and how this causes the side to side stop. Would you notice this problem all of a sudden or would it get worse over time? Thanks
@EngineeringSiblings2 жыл бұрын
It suddenly falls off and than its this sloppy. If it happens slowly than its jus wear on the system
@daveyboiyeah2 жыл бұрын
I have this problem too. When the engine is hot the gearbox gets stiff side to side
@VyckaWild3 жыл бұрын
Would this fix work if the gear leaver gets super stiff and barely changes the gears? Got to a point where you have to use a lot of force to change the gears, feel like it's stuck in strong clay
@hussssshie3 жыл бұрын
If you can switch gears with the engine off, it's the hydraulic clutch bearing or pressure plate.
@falloutthree3702 жыл бұрын
Hi, My gearstick had this same symptom, but while driving my gearstick became so loose left-right, and I realised I only had 3rd and 4th gear available, so I limped home without stopping... Navigated the traffic lights, etc... I tried this, but something else is wrong I think, something looks jammed when I look through the hole I drilled...
@EngineeringSiblings2 жыл бұрын
do you have an way to send a picture ? It could be that your cable got detached (most likely) and than its much bigger work to take it off
@darklive1233 жыл бұрын
Its the same operation if the gearbox os slopy in the front and back move?
@arrowblue39096 жыл бұрын
What if the plastic bush at 4:14 is broken? i drilled a whole and saw the bush is broken. How do you fix this one?? can you explain a bit please? or how to pull out this mechanism?
@edwardsumnersumner53946 жыл бұрын
I'd like to know about that too.
@thecredite5 жыл бұрын
do u have a video for the automatic gear box?!
@maliknirvana1890 Жыл бұрын
Hello, i had a problem today, the 6th gear jumps when i hit the gas , when im not accelerating it stays ok, but once i accelerate it jumps, only 6th gear .. would this fix it?
@mbalunovic Жыл бұрын
Sadly most likely not. :(
@oreuric6036 жыл бұрын
Milose, molim te, hoces li detaljnije reci, dakle saltac ne moram vaditi iz auta, probusim rupu i sta je procedura? Samo gurnuti plastiku unutra? To je sve? Hvala unapred
@oreuric6036 жыл бұрын
@@EngineeringSiblings Hvala puno! A kako se vadi saltac? Da li moze kad se skine konzola ili auto mora ici na dizalicu, da se skine auspuh, zastitni limovi itd?
@CarloIonutzz4 жыл бұрын
Could you explain why did you make that hole? Can't be opened without that hole? :-? :D
@EngineeringSiblings2 жыл бұрын
I know its late reply. I made the hole ao it can be repaired without taking it of the carr which is a much more demanding job than this
@MaNNeRz913 жыл бұрын
Remowe the fron plastic cower. The captions are in Russian?
@EngineeringSiblings3 жыл бұрын
That is strange. We dont have Captions enabled. Are you sure your language is not set incorrectly on YT? Anyway ask what do you mean and Ill do my best to answer it :)
@rogeriolitoralgoncalves10662 ай бұрын
Não existe reparo para esse problema
@EngineeringSiblings2 ай бұрын
well, you just need to watch the video :) if the plastic is however completely worn, it can be replaced with a plastic "pipe" or hose
@marcelorebelo68644 жыл бұрын
Anyone know the thread size of the gear stick is it a m12?
@marcelorebelo68644 жыл бұрын
OK ok I'm looking to get like an aftermarket gear knob and is the actual gear stick was threaded it would be easier you know