Repaire and Upgrade Bait Boat FX88, D18B, V010, VERY100... Part 2

In this part, I showed how I maintain electric motors and how I use a magnet as a holder for the rig to keep it from getting tangled.
See also the first part,
I recommend all this to be done before use.
Part 1:
• Repaire Bait Boat FX88...

[@sylwiachaber9667]

Thanks for the report - good job! :D Now I know what I have to do first - after buying this boat and before using it for the first time. Thanks a lot and regards!

[@peterzstandalone5178]

Nice tip with magnet!

[@maskrc1767]

Awesome Video 👍👍👍

[@anglerzgadgetzasia1896]

Great part 2

[@luismanchego6856]

Hi Robert I bought a similar battery to the one that came with the boat ( typical Chinese batteries for this boats) It says on the label that is 5200 mah and the charging voltage is 8.4v and the output is 7.4v but it doesn't mention any amperage or anything else. And I am concerned in case I burn the board or the motors... You know how much the electronics can take or if it is safe to use this type of batteries? I would appreciate your advice. Thanks 👍

[@mayster2298]

Bardzo fajny film, dobra robota. Posiadam taką samą łódkę wersja V18 która posiada takie samo sterowanie, pilot i płyta. Mam pytanie jak kupię na aliexpres taką samą płytę sterującą żeby podmienić moją obecną czy bez problemu połączy się z moim pilotem? Czy muszę kupić komplet płytę i pilot?

[@jasondyer292]

Hi would you be able to point in the right direction for getting parts I need the plastic release clip on the rear hopper. Thanks

[@RobertZovko]

www.aliexpress.com/item/1005002462104445.html?spm=a2g0o.order_list.order_list_main.23.59961802tg4Mhv

[@ibraheemhabahbeh1044]

Great video as usual, can you please share a link of spare part or at least specifications of the motors.

[@RobertZovko]

a.aliexpress.com/_mroynEY

[@emanuelefancellu4721]

Buongiorno a tutti io ho lo stesso modello e ho portato le lenze a 300 m in mare

[@aggelosm.1689]

Ein sehr schönes Video. Aber eine Frage bleibt unbeantwortet: Was macht man, wenn das Wasser in das Innere des Motors eingedrungen ist? Leider passiert das bei diesen Unterwassermotoren sehr häufig.

[@RobertZovko]

With regular maintenance this should not happen. Everything works for me for now.

[@maxeleu295]

Hello I have a question, why does the remote control beep 3 times every 5 seconds?

[@RobertZovko]

Which model is in question (motherboard)? Is it connected? Does everything work?

[@erikmate7379]

Is anybody know that the remote is the same on all model? As i have 1 like this but that only can set 4 gps point so i found a gps and the motherboard for a 16 point one and just thinking to swap over but i do not know about a remotes

[@RobertZovko]

maybe a better solution: kzbin.info/www/bejne/nYHdk4Bvqbt9lcksi=VWc1zbSYyjxVxDh5

[@akoswitzelsberger3320]

Hello Robert! Could you please help me? My remote for this got broken, so I have ordered a new one but I cant pair the new remote with the boat. The new controller is totally the same as the old one.

[@RobertZovko]

It may look the same, but what matters is who the manufacturer is, the number of channels... Do you know the pairing process? Sometimes you have to try several times and move away at least 1 meter.

[@akoswitzelsberger3320]

@@RobertZovko Hello Robert, thank you! I will try to pair them from a distance of more than one meter. I guess I know the pairing process: push and hold the button left from the powerswitch, pusht the powerswitch, tjan turn on the baitboat and wait until the beep. There is no beep coming :/

[@RobertZovko]

@akoswitzelsberger3320 right to the left of the main switch, but that switch has 2 positions, up and down. Press down like the main switch when turning off.

[@akoswitzelsberger3320]

@@RobertZovko thank you Robert! I will try that, I didn‘t know about the second position of that button. I will try that. In case it shouldn‘t work, do you know how to change the chanel of the remote? I have done so much research on that question but I am unable to find info about that. :) Thank you so much.

[@JakubowskiRoman]

Hello Robert I don't know how else to contact you, so I'm writing here. I was very intrigued by the short videos on your channel. I see that you have modified the deeper, what distances do you get by adding the antenna? how did you mount the deeper in the boat (you can see two antennas)? Give some information, it's a very interesting topic. I just bought a V020 and I'm going to buy a deeper one, and thanks to your implementation, I know what to expect from v020 and how to prevent possible leaks. It will definitely improve the boat before launching. Again, I'd like to ask for more information about deeper

[@RobertZovko]

I will make a little video soon. With an external antenna, the range does not increase significantly, but it is reliable even on waves...

[@JakubowskiRoman]

I think reliability in the waves is more related to the fact that the deeper is mounted directly to the boat, which is associated with greater stability. I wonder if you can remove all the electronics from the deeper and glue everything without disturbing the bottom of the boat. The transducer should be able to handle the bottom of the boat and moisture sensors can be bridged under the switch. I'm waiting for a video of how you solved it@@RobertZovko

[@JakubowskiRoman]

In this video it is obviously shown with another fishfinder. The use of ballast is also interesting. kzbin.info/www/bejne/oIOygZiqlphqqbc

[@MrKato84]

hello nice video, Which magnet do you use?

[@RobertZovko]

diameter 8 mm, thickness 2 mm, dimensions are not important, it is important that it fits and that the magnet is not too strong (you can always add a stronger magnet to the smaller one without gluing)

[@TheJuzni]

Poštovani! Danas sam dobio svoj brodić, ali nije ovaj nego jedan kinez. Išao sam ga testirat i igrom slučaja sam pregazio daljinski upravljač. Moje pitanje je da li drugi isti daljinski može upravljati brodom ili je potrebna nova instalacija?

[@RobertZovko]

I ovaj je kineski i može drugi daljinski samo se treba upariti. Jednostavni postupak.

[@TheJuzni]

@@RobertZovko huh, jest vama. Imate neki link da se poučim?

[@RobertZovko]

@@TheJuzni Prvo, koji brod imate?

[@TheJuzni]

@@RobertZovko Sličan je ovome. Isti ovakvi daljinski. Je li ovo sve što trebam uraditi? Poslao sam vam link s Alia ali je nestao. kzbin.info/www/bejne/inbCho2tq7-an68

[@RobertZovko]

@@TheJuzni Da, samo to.

[@marmi9489]

Can the engine be lubricated in the same way in the V020 model?

[@RobertZovko]

yes, they are the same engines (390)

[@Antonio-tv1lv]

Doesn't the magnet interfere with the compass?

[@RobertZovko]

no

[@lubiloopsenk3982]

what board is this with 4 pin or 16 pin

[@RobertZovko]

which board???

[@TheJuzni]

Evo me opet. 🙃 Ribari su mi rekli da ću imat problema iznijet ješku na 200 m kad ima više vjetra i kurenta. Stvara se trbuh i onda se treba na poziciji dat gasa i blokirati rolu da bi se upredenica nategnula. E sad, i mene nema gasa od onoga što ima a to nije puno. Može li se stavit jači motor?

[@TheJuzni]

Moj brodić je D16.

[@RobertZovko]

Slažem se sa ribarima, probao sam ga na moru i ako ima malo mora taj brodić nije siguran, preslabi motori i nestabilan trup. Ako vam treba za more u svim uvjetima ja bi tražio malo robusniji model...

[@TheJuzni]

@@RobertZovko dobro, evo sad je gotovo. Molim vas prvo mi recite mogu li naručiti daljinski preko linka koji ste dali za FX88 jer sam naručio krivog koji se ne može uparivati. Isto tako da li mogu i motor naručiti i koliko vidim jači motor je pod “new motor” ili je to samo nova verzija. Na Aliju sam našao jednog koji je 7.4 V i daje 10000 rpm te je s propelerima 27 mm što mi odgovara.

[@kojenormalan]

Odličan klip. I sam posedujem istog ali u zadnje vreme nema gps pozicioniranja tj. nema signala na daljinskom a sam brodič vrši pozicioniranje na komandi daljinskog ali se ne prikazuje na daljinskom. Pa zato onda krene sam od sebe da vozi bez mogučnosti kontrole istog. Reset nije pomogo. Jel može savet eksperta, kako to rešiti? Bile več situacije kde sam moro otplivati po njega 😂🍺

[@RobertZovko]

Kako ste resetirali?

[@kojenormalan]

@@RobertZovko Reset sam vršijo pomoču kombinacije tipki OK i gornja leva tipka. Za drugo neznam. Problem je što nemogu više da memoriram pozicije tj. nema gps pozicioniranja. Pa kako stoji to ga zbunjuje i onda mogu samovjoš obično da ga vozam što nebi bijo problem ali onda sam odsebe krene u svoj neki pravac i nestaje a komande na daljincu neprepoznaje. Šta bi tu po vašem bilo najbolje tešenje? Da kupim drugog najverovatnije nisam rešijo ništa.

[@leeparker5827]

Where can I get the magnets many thanks

[@kupadrutu]

hi, could you please help me figure out what broke in my boat? we disassembled it because the engines began to squeak. after assembling, the pilot boat connection stopped working, pairing does not work. on the remote control flashes a yellow-green light, after some time one of the engines in the boat turns on. could i contact you via messenger?

[@RobertZovko]

check if all the connectors are in the right place and have good contact, if the motherboard is receiving voltage... If that's all right, it's probably a fault on the motherboard.