Repairing a leak on a condenser coil. This is how I repair leaks on condenser and evap coils.

In this video I use the ASCO #3 Tip and Torch set from TruTechTools. One option is Cool Air Products, Smart Seal. Another is brazing the leak with Solderweld's 15% Silver Solder.
For More Info, go to:
www.trutechtools.com Use HVACGUY as the PROMOCODE to recive an 8% discount on select tools
www.solderweld.com
www.coolairproducts.net

[@josephastier7421]

You put so much heat on that tube I was surprised it was still there.

[@cochisecounty_travels]

It’s all about flame management. I repair microchannel leaks with a brazing set up whenever it’s needed. I prefer map gas though. But it’s really easy with Solderweld’s AlCop rods

[@edthacker3600]

i am in need of a repair on my coil here in benson az. you got time ? Are you still doing repairs?

[@cochisecounty_travels]

@@edthacker3600 no. But there are some good companies in Cochise County and Tucson that should be able to do this.

[@U2BER2012]

So you didn't feel necessary to pre clean the copper tubing before brazing it?

[@cochisecounty_travels]

Yes. Pre clean is always needed on oily coils. But if it’s dry and clean, I will sometimes not pre clean.

[@Sr5taco]

I’m dealing with this issue on my window ac. Found a small rock wedged though the fins and it punctured a small gash on the coil. The ac was running for a few hours before I noticed it. The reason I checked in the first place was because it wasn’t cooling. Is there anything I need to refill that leaked out of the hole? Or will it begin to cool again with no issues after the leak is plugged?

[@cochisecounty_travels]

It should do ok after you repair the leak. But it’s a mechanical system, so you won’t know until it starts.

[@popcorn6931]

if there's still refrigerant in the coils, how would you clear them out?

[@cochisecounty_travels]

Recover it like normal.

[@jamesrogers4674]

Going to try this in the morning. I was told that the copper is extremely thin and easy to melt through. It's the top coil going through the galvanized metal so it will probably be time consuming to remove the metal. Wish I had more experience with temperature control. Any suggestions that may help me not melt the world down?

[@cochisecounty_travels]

It is very delicate, so practice on a coil and use a light flame.

[@jamesrogers4674]

@@cochisecounty_travels I was successful at fixing the leak. Ordered a 00 tip from Amazon and was able to get a lot smaller flame. Thanks for the reply.

[@brownbriansjeep9020]

@@cochisecounty_travels what is that torch called

[@wakawaka1976]

How much does it cost to get this done?

[@cochisecounty_travels]

Whatever the cost of the solder is. You provide the labor

[@leoayoroa7217]

Can you still find r22?

[@ranfulai1]

How do you find the leaking area?

[@cochisecounty_travels]

Pressure test with a small amount of R-22 and Nitrogen. The leak detector will sniff the refrigerant

[@macapodaca]

I’m glad there wasn’t a close up of his work.. not thee best example all around.. from the “leak stop” to caking a evap coil up with solder makin a huge whole too hahaha

[@cochisecounty_travels]

Thanks for the comment.

[@dougdelzer6891]

Can you use flex seal?

[@cochisecounty_travels]

No

[@theodorecarbajal2975]

Will damaged fins cause any issues? 90% of my fins are brand new but the bottom of the fins kind corroded but ac works great

[@cochisecounty_travels]

You should be OK. But keep a fin straightener close by and straighten them out if needed.

[@aircoolhvac6404]

#aircool

[@cochisecounty_travels]

Look up ASCO Torches. I got it thru TruTechTools. If you purchase there, use HVACGUY as the PromoCode and you should get an 8% discount