Honestly I have watched 1000s of videos over the years for shade tree mechanics and this is the best how to video out there 🙌
@mario17-t342 ай бұрын
Yes, video is super, but there are super skills too. I tried to disconnect wire and can' t, with 9" and short pliers, my push tab located on 2pm. Everobody using pliers to do this? or some people use long screwdriver going near generator opening.
@headhooligan37962 жыл бұрын
This did the trick on my Accord, would suggest adding extension magnet “thingy” in case you do not use enough tape in the socket or if drops w/ an extension socket. Thank you for the video!
@darondouglas6160 Жыл бұрын
Thanks for posting. I have about 429,668 miles on my 03 Accord EX 4 cyl. I watched several videos before attempting this. It took me less than 8 minutes to complete and saved a lot of $$ doing it myself. I used scotch tape to hold the new sensor in the 27mm socket as I hand-turned it into place. Removed tape from socket then snugged with ratchet. I did unhook the negative from battery in order for the engine light to go out. Runs so much smoother.
@bokhenik Жыл бұрын
Impressive mileage! I’m only at 247,000.
@vetteracer4272 жыл бұрын
By far the best. No jacking car up. No taking that pain in the butt black bottom cover off. Thank you. '03 CRV 245k
@teban65602 жыл бұрын
I just got the dreaded code on my wife's 02' CR-V. I have been watching different ways to do it. Top vs bottom. I'll try doing it from the top first since I hate going under and removing all those clips. She still runs like a champ at 180k+ miles. Love the CR-V!
@hanginon1293 Жыл бұрын
Just did this job today. Can't believe some people are taking the manifold off. 20 minute job tops. Thanks for Video, it help 😊
@thscott12 жыл бұрын
Thank you very much for making this video. I was able to do this a couple days ago on my son's 2003 Accord. It was challenging, but I got it done following your instructions and techniques. Hardest part was getting my hand squeezed in to be able to plug the electrical connector back in. I was able to remove it using long needle nose pliers, as you suggested. Also, I had some difficulty getting good lighting in there. But, much easier than removing the intake manifold.
@bokhenik2 жыл бұрын
Thanks! Agee, I've done it both ways and this is better than removing the bracket below the intake and all the hoses.
@fox7anthem4312 жыл бұрын
Was about to remove IM, until I seen this. Easiest job, was done within 20 min. Thanks
@bokhenik2 жыл бұрын
Glad to hear it!
@andrewjc132 жыл бұрын
Just made this repair on my car following your guide. It went great! Thank you so much! Saved me hundreds in mechanics bills.
@matthewmatthew11993 жыл бұрын
Thanks! This helped me get rid of the CEL code. I had to buy the 11" long needle pliers at HF for $5 to remove the plug to the sensor. A socket extension of 7" or 8" would have been perfect to remove the sensor, my 10" was difficult to use due to interference with the fan. After screwing on the new sensor, the plug tab was now at the 3 oclock position (not 12 oclock like old one). So it was kinda hard to to plug it back it, but finally managed using just fingertips. No more P0325 code. I bought the sensor at Adv Auto P for ~$55
@MeowKitKatKitty11 ай бұрын
Wow saved me hundreds of dollars! Thank you!
@xtremebroccoli2 жыл бұрын
Just did this on my 03 element. Might be easier to remove intake… but not too bad doing this method. Not as much room under the hood for the element as in this video but was still doable. Hardest part was plugging connector back in on new sensor lol. Took about an hour to do for me. If you don’t like shoving your hands in tight spots with poor visibility take the intake manifold off.
@mario17-t342 ай бұрын
Thanks R!!! best video in the world, spent today 20min to plan operation, my tab located on 1pm location, and it's hard to reach with my 9' pliers b'z of wires. Will give a try with shorter one like you using.
@dv85572 жыл бұрын
Thank you for making this short yet informative video with very clear instructions. I think I’ll be able to switch this thing out myself now!
@bxdubs55773 жыл бұрын
Thank you bro, this code just popped up for me, and the first video that pops up is the one that helped me.
@95countach2 жыл бұрын
Finally, I was wondering if I can access it from the top side. It looks like there's more room at the top, just harder to see, but at least I can see what is involved. Thanks for posting this video! 👍
@Christopher-pe6zj3 жыл бұрын
Quoted $360 for a $60 part.. literally some blood sweat and tears but I saved $300! Go me.
@victorbelmares27223 жыл бұрын
Couldn't unplug with pliers I was able to grip plug with needle nose pliers then used long screw driver to push down on the clip then pulled with the pliers. couldn't get my hand under manifold to plug back in so i tried to the left of the manifold and had plenty of room to get my hand in not underneath the manifold on the left side hope this helps someone
@hanginon1293 Жыл бұрын
What do you mean you lifted the manifold? You didn't have to loosen anything?
@victorbelmares2722 Жыл бұрын
@@hanginon1293 read it again I didn't take off the manifold my hand was too big to get under so I went through the side of the manifold the left side
@hanginon1293 Жыл бұрын
@@victorbelmares2722 OK my bad, I read it as lift instead of left. I have to replace this so I'm watching and reading as much as I can. I guess my eyes are getting blurred
@victorbelmares2722 Жыл бұрын
@@hanginon1293 no problem
@amoney19344 ай бұрын
Why u lying @@victorbelmares2722
@sailingaristos24722 жыл бұрын
FANTASTIC vid. Thank you for being so clear.
@mikefranklin35283 жыл бұрын
Most concise video ever recorded.
@Randyman41262 жыл бұрын
Excellent video!!You know I don't drive a Honda or Acura but enjoy watching videos on repairs..I just want to say you made a very detailed video that is str8 to the point, with the correct steps showing how to do them, in a quick video that isn't strung out over 25 -30 mins with useless banter lol.. So again,very very excellent vid showing people how to diy!!
@IkarosCanFly2 жыл бұрын
I found this job way easier with a 27mm spanner for removing the sensor and two long flat headed screwdrivers for removing the plug. I also did this from under the car.
@charlesclarkejr21912 жыл бұрын
My first thought was why plyers except maybe to replace the the plug?
@imdawolfman26983 жыл бұрын
I have to go back in to replace a 3rd party knock off knock sensor I just installed following this procedure on an '05 Element. This time I will loosen the intake manifold. It took me a day and a half, 10 hours, of swearing last time. I expect a 2 hour job today.
@bokhenik3 жыл бұрын
Which step did you find to be time consuming or difficult?
@imdawolfman26983 жыл бұрын
@@bokhenik - All of them. It seemed like the old - 'trip over a dollar to save a dime'. Trying to reach the release tab on the wire plug 2 hours. Getting the old sensor out 1 hour. Lining the new sensor up and getting it started 1 hour. Tightening the sensor to 25 fp .5 hour, but incomplete* Getting the plug back on the sensor tab 2 hours - not counting drive time to the parts store to buy a remote grabber tool. *believe I was just tightening against the swivel, and hoping the sensor is still loose because it didn't fix the P0325. This time I'll back the manifold off to save time and frustration, as well as have space to test the circut.
@antoinettekida-jeffers70523 жыл бұрын
Thx, the first one I watched was a bit more detailed, but yours is great too, thank you.
@apap30292 жыл бұрын
Thanks I just use your video and got it complete 💯
@bokhenik2 жыл бұрын
Nice!
@waldemarzysek15263 жыл бұрын
Very Good video. Wymiana czujnika spalania stukowego . Honda FRV
@macbruno3572 жыл бұрын
Great video, let's see if it works. Thank you.
@mario17-t343 ай бұрын
This is the best video, thanks my friend. @1.53 I see that wires zipped to the bigger tube, is this right? Do I need to cut/release that clamp
@macelo10173 жыл бұрын
After removing fe de fender plastic I use 2 screw drivers to unplug it, I used a 1/2 “ drive sucket with a 3-8 reducer and short ratchet eventually you will figure out how to get your hands in there
@gigrinker3 жыл бұрын
This is so helpful I just did this on my element. Additionally helpful tip if you don’t have tape you can use the socket with extension to hand feed the new sensor. Just put piece of printer paper small size just enough for sensor to bind with its install socket. I didn’t have tape lol but this video saved me money
@bokhenik3 жыл бұрын
Nice tip! Glad it worked on the Element.
@paulrush91663 жыл бұрын
Thank you! Perfect video!
@walkerwalker2725Ай бұрын
Does this apply for the special edition also.
@charlesclarkejr21912 жыл бұрын
I wish I saw this video 6 months ago..while it was warm outside! Now I have to do this in the cold! Lol
@angelg17332 жыл бұрын
amazing video, random question! what does the knock sensor do??
@TheTexican052 жыл бұрын
It’s senses for any detonation within the cylinders, and then tells the ECM to dial back ignition timing accordingly, often just 1 to 3° at a time. It’s a very important watchdog for modern engines. In case you have bad gas, or an engine that is in a poor state of tune from lack of maintenance. Supplemental research: …google “engine pre-detonation” and “engine knock” for further learning. ✌️ 🔧
@manlb92543 жыл бұрын
Neat way to do this but the intake manifolds on these accords are really easy to take apart. They are a 2 piece design. It is more difficult on a crv and element for the radiator fans sit closer to the manifold and do not give you any wiggle room
@bokhenik3 жыл бұрын
I found it pretty tedious to remove the manifold when I replaced my starter a few years ago. Even on the Accord it was a bit of a pain to remove the bolts on the bracket below the manifold. Plus technically the gasket should be replaced which adds to the repair cost. If I had to replace this sensor on the accord again I’d absolutely use my method. I can probably do the whole job in
@4seeableTV3 жыл бұрын
@@bokhenik Replacing the starter the was of my least favorite things to do on the Accord. But I had the alternator go out a couple of times (cheap auto parts store brand and it's second replacement), and those are much easier to do. I'm needing to replace my knock sensor now, so your video has shown it's doable without too much hassle.
@bokhenik3 жыл бұрын
Make sure you get a reputable knock sensor. I’ve heard that knockoff eBay knock sensors have poorly machined threads that can mess up the thread on the block.
@billiegreen5018 Жыл бұрын
Much easier to remove the intake manifold to get the job done, and I’m a girl!
@curtisbrown73895 ай бұрын
I agree 💯%justbremove 45 12m and take bottom bracket loose 12m also pull too side knock sensor sit right there
@curtisbrown73895 ай бұрын
6 bolts total remove hose and one other bracket screw out and back in
@jayvito36672 ай бұрын
Very helpful bud
@garrettsontag7813 Жыл бұрын
Can I do this job with a 3/8 drive instead of a 1/2 drive? If so, would it be possible to recommend me the correct socket? Thanks in advance
@bokhenik Жыл бұрын
3/8 should be fine. You need a 27mm socket deep enough to clear the plastic connector on the front of the sensor.
@mario17-t343 ай бұрын
Best VIDEO !!!!
@hieppham88343 жыл бұрын
Thank you
@normcarguy45713 жыл бұрын
Thanks for your video it helped
@joshjoshkabosh3 жыл бұрын
This is really awesome, gonna help me out, thanks man
@nickjonas98762 жыл бұрын
really well done video
@justinbouy31533 жыл бұрын
Great video thank you so much!
@walkerwalker27255 ай бұрын
It's that simple and a shop was going to charge me 1,000 dollars.
@megamarcbeats2 жыл бұрын
Great video man!
@NiMi93 Жыл бұрын
Thank you! It worked :)
@frostbite85722 жыл бұрын
Thank you good sir
@xvirk79324 ай бұрын
Can the knock sensor also create problem when i start my car. I am having problem starting my honda accord. Can this sensor be the reason?
@bokhenik4 ай бұрын
I don’t think the sensor would cause starting issues. Might be a starter issue in which case you would need to remove the intake
@xvirk79324 ай бұрын
@@bokhenik thanks for the info but i got a rebuilt starter last year i dont think starter would make me that problem.
@Roobetsbestt3 жыл бұрын
Thanks, very helpful
@peb8484 Жыл бұрын
Did you use the original Honda knock sensor or one from Amazon?
@bokhenik Жыл бұрын
I used a Beck and Arnley sensor (from Amazon) and it’s still working fine. My first attempt was with a knockoff Honda sensor (eBay) and it had poorly machined threads which almost messed up my engine block. Avoid those.
@mfl-metaversefootballleagu18193 жыл бұрын
Just remove the intake. By the time this way works. Removal of the manifold makes it a 10 minute process, this way could take hours.
@Cheesusrice692223 жыл бұрын
Or 1 1/16th inch if you dont have 27mm socket
@Dean-rs2nt2 жыл бұрын
Knock sensor replaced. P0325 still checking. Wiring traced and all good.. P0325 still checking. Anything else to diagnose ?? 2008 Honda accord CL7 155bhp
@joevignolor4u9492 жыл бұрын
Aftermarket knock sensors that you buy at the auto parts store are notorious for not working correctly and causing the same codes to reoccur. That's why many people recommend only using original OEM knock sensors. I had this problem on my Lexus with a V-6. I bought two new knock sensors and the associated wiring harness off of eBay but I made sure the parts were original Toyota components that were still sealed in the original bags. Besides buying the parts from a dealer (which will be very expensive) buying OEM parts off of eBay (a lot cheaper) is okay but you have to be very careful about what you are getting.
@hapetaa Жыл бұрын
DID YOU USE GENUINE SENSOR or After Market?
@bokhenik Жыл бұрын
I used aftermarket. First one broke after one year. Second one is going strong (Beck Arnley).
@bokhenik Жыл бұрын
One more thing, don’t use fake OEM eBay knock sensors. They have poorly machines threads that can mess up the thread on the engine.
@alanpachecoosuna32773 ай бұрын
Does anyone know the severity of this issue. I scanned my car and it said to change the sensor as soon as possible if I had driving issues. That it could damage the main system.
@kimoclyde11 ай бұрын
How has this aftermarket knock sensor held up?
@bokhenik11 ай бұрын
I initially installed an Autozone sensor which lasted about a year. I replaced it with a Beck Arnley and that has been good for 3 years now.
@kimoclyde11 ай бұрын
@@bokhenik Good. BA is the one I ordered. Thanks!
@wonyabyrd6855 ай бұрын
The old one fell in and i cant locate it. Will it damage anything if i leave it and just install the new one?
@bokhenik5 ай бұрын
I highly doubt it will damage anything. I’d install the new one and see if you can fish out the old one later. Maybe try a magnet.
@jordanp20413 жыл бұрын
Why dont you have any video of you actually removing the sensor connector?
@bokhenik3 жыл бұрын
Good idea. I’ll record a video doing this live.
@Discovery123.2 жыл бұрын
I had engine light on and code read P0325, I disconnected the battery negative for 1 minute and reconnected, everything works normal, no engine light or code come back. Do that before you change the sensor just to be sure.
@TheTrexlertracey2 жыл бұрын
I did the same but it will just reset and eventually come back on
@joevignolor4u9492 жыл бұрын
I had this problem on my car. I found that resetting the code and turning off the check engine light only worked as long as I drove the car under 55 mph. If I tried to drive over 60 mph the light would come back on again. Also, driving the car with a defective knock sensor can damage the engine internally. The computer uses the knock sensor to adjust the ignition timing to eliminate the knock. Without the knock sensor you can have undetected pre-ignition that will eventually damage the engine.
@lanellelee4626 Жыл бұрын
What size socket apdator is connected to da 27mm...
@bokhenik Жыл бұрын
1/2 inch
@lanellelee4626 Жыл бұрын
@bokhenik okay cuz I'm in process of tryn to replace mine and it's frustrating me 😤
@zoilohernandez56202 жыл бұрын
Do you need to disconnect the batteries?
@bokhenik2 жыл бұрын
I didn't as this sensor is not powered when ignition is off. But it may be a good idea a precaution.
@jafoura1233 жыл бұрын
It is easier to remove the intake and then replace the knock sensor , 15 minutes guarantee, remove the intake hose , remove the throttle body , 4 bolts, then 3 bolts for the intake along with 2 nuts, one vacuum hose , that’s it , you don’t need all that hassle, trust me go the easiest way
@bokhenik3 жыл бұрын
If you go that route, its better not to remove the throttle body from the intake and just disconnect the intake hose. First time I replaced by knock sensor, I spent an hour cleaning off the throttle body gasket and another hour buying a replacement. As far as which method is faster, I think it depends on technique. It took me a while the first time but I did it several times to film the video and can do it in ~20 minutes.
@kdlee33163 жыл бұрын
how do you unclip the knock sensor?
@myalaskanlife3 жыл бұрын
Squeeze with pliers
@rickjeffjeff5 ай бұрын
Great video.... I don't have a girlfriend so I can't get a mirror.Going to take it to a shop.
@sosick20054 ай бұрын
Having a hard time removing the connector. Cannot get my hand in there to grab it and securely pull it off.
@bokhenik3 ай бұрын
Did you see my other video on how to remove the connector?
@sosick20053 ай бұрын
@@bokhenik I did not but I got it and thanks for replying
@ChrisHarrison-w4m10 ай бұрын
This doesn’t work well at all on a 2006 Accord, for several reasons, just one of which is, on my 2006, there is a large piece of plastic under the intake manifold that prevents you from seeing the sensor. Another is you need a very specific length of needle nose. I tried to use this method, and wish I had just done it by the remove the intake manifold method. I would have had it done in considerably less time.
@gooby8953 Жыл бұрын
I've got wires in the way that I can't get it around
@chandlerautomotiverepair5733 жыл бұрын
this will not work for a CRV...
@StevenFrost-vx7mi10 күн бұрын
It's the exhaust manifold not the intake manifold
@bokhenik8 күн бұрын
Exhaust manifold is on the back side on these engines.
@solidkingcobra2 жыл бұрын
Completely failed on this task because I did not get a mirror because I do not have a girlfriend. Also I got big fat hands.
@solidkingcobra2 жыл бұрын
all joking aside. I actually pulled it off. I was able to replace the knock sensor and I felt pretty damn proud being able to do it by myself instead of going to a mechanic. Thank you so much for this handy dandy videos. The tape trick was super effective.
@bradleydeherrera83963 жыл бұрын
Why add the “girlfriend’s mirror” part? 🤔
@albertangelomorin93453 жыл бұрын
Means you cant replace the censor if you are single
@counter5463 жыл бұрын
@@albertangelomorin9345 damn it! That's why I couldn't do it myself.
@random21883 жыл бұрын
Hahaha
@ruz61353 жыл бұрын
Hahaha I thought the same thing. I don't have a mirror, great, now I have to get a girlfriend 🙄
@danamiller60492 жыл бұрын
Pick, pick, pick.
@jabbaweezy3 жыл бұрын
3:21 Girlfriend sold separately
@bokhenik2 жыл бұрын
As requested, I have uploaded a companion video that shows a more detailed view of unclipping the connector: kzbin.info/www/bejne/fJXTfZuurbSLnsk
@Jburnias14 Жыл бұрын
This S.H.I.T dont work for a acura tsx there is not enough room to fit any kind of pliers uner the manifold
@edgarsaldana_3 жыл бұрын
I don't have a girlfriend tho
@twotone99082 жыл бұрын
You didn’t show any movement on replacing sensor or clip😡😡😡😡😡😡