awesome old instrument reminds me of lakhovskys multiple wave oscillator
@omarplazas87492 жыл бұрын
thanks
@ZeroPointZap3 ай бұрын
I need to replace my capacitor but am very confused about the choices. The one that was in there says 2KV. Is that the output? Would any 2KV capacitor work? I just installed one that is working but my electrode isn't glowing and there is not break in the current... Can you help me? Cheers
@Bigshoots86 Жыл бұрын
Is that the same capacitor someone would use on a 120v wand?
@FreedomFactory3D Жыл бұрын
How can you check to see what size capacitor your need or is there a general type that will work with most?
@gelibobbabble53312 жыл бұрын
Hello, Awesome video. You say to test the output to make sure you get the correct condenser for my machine. how do I do that with a multi meter. Also my rota switch is attached to the coil and has a spring in the middle of it, it won't change the amount of current coming out the wand. Do you think this fix will work? thank you for your time
@athansky25 Жыл бұрын
Polypropylene vs Polyester capacitor which is good? I got old Original Haider device (1930s regular with just a few electrodes) but the Capacitor/Condenser was broken and last used abt a decade ago, but I don't know which cap ratings to use to restore it ? 220V VAC power.
@engjds Жыл бұрын
Polypropylene, you have to be careful with the voltages, often they state the DC voltage even though they can be used with AC, anything below 1000VDC will die quickly(it will just lose value) depending on the amount of inductance in the coil, I suggest trying to get as close to 2Kv DC as you can, this will typically have a size of 1cm or more diameter, as for value, they vary between units significantly, I have had them go up to as much as 5uF, but typically they might be 50nf to 500nf, good to keep a selection in and see which gives the best spark, start with the higher values as lower resonant frequencies give more powerful sparks unlike the modern version of wand that are around 500Khz, you want to aim for 200Khz-you can check that with a oscillascope place a couple of meters away-the probes will pick up the signal without any contact (DO NOT CONNECT THE PROBES!!" Hope that helps. Best models seem to be the Rogers Vitalator-they have good wand transformers which is usually the first thing to give up the ghost.
@frankfreeman16782 жыл бұрын
Do you think you could draw me up a schematics of how the wiring works. Like how the wiring feeds from the potential meter ,capacitor to the coils. I mean just like the simplest drawing you could do like show the wires going how the wires all lead into what. I know it doesn't have a potential meter but I mean if it did you know how would that work or how the wires come off of the little rotor switch that you have and run do they run into the capacitor first and then into the coil? Okay thanks a lot appreciate it. Frank
@INS19772 жыл бұрын
I got one without condesor and wires... Need repair
@msmagpie5620 Жыл бұрын
What are these machines used for ?
@Bigshoots86 Жыл бұрын
Nowadays ? Sensory play
@khalaf_stocks3 жыл бұрын
Hi Mirko , do you have other social profile ?. It's very required in such a time to not miss contact with you if anything happens to your youtube profile . Thanks
@MirkoKulig3 жыл бұрын
Hi. You can find me on FB. Alternatively, I do have a Bitchute but with few videos: www.bitchute.com/channel/PYpjW4kzZkCn/
@khalaf_stocks3 жыл бұрын
@@MirkoKulig Thanks , you know with all this going on , i don't trust regular social media sites ...
@DolezalPetr3 жыл бұрын
I have two violet rays, but in bad condition, one is from 1932 and the other from 1933 and I have a lot of electrodes for them, but I dont have the original manuals or electrode lists for them, could you please maybe scan the manual and the electrode list? I would greatly appraciete it!
@MirkoKulig3 жыл бұрын
Hi, I already intended to do that, but it's mainly written in German, not sure that helps...
@DolezalPetr3 жыл бұрын
@@MirkoKulig I have no problems with german
@TarsierTV3 жыл бұрын
@@DolezalPetr Ok, I will try to scan and publish it in the next few days. You will be able to find it on my website mirkokulig.com, under More/Download. If you contact me from there with the contact form I will let you know as soon as it's posted.
@TarsierTV3 жыл бұрын
p.s. just because I need your email address
@DolezalPetr3 жыл бұрын
@@MirkoKulig Thank you a lot, I will check out your website, I will contact you.
@taigongpisa3 жыл бұрын
Ciao Mirko, sono Sandro. Purtroppo hanno chiuso il mio canale, puoi immaginare perché... Volevo farti i miei complimenti per l’ultimo video che hai fatto, quella scoperta è davvero sconvolgente, la sto facendo girare anche sul mio gruppo Telegram. Vieni a trovarci, cerca L’ALTRA GIUSTIZIA. Un abbraccio 🙏
@MirkoKulig3 жыл бұрын
Grazie per gli apprezzamenti. Per favore, Quale Sandro? Il gruppo telegram non lo trovo...
@taigongpisa3 жыл бұрын
@@MirkoKulig Io e Claudia Cusenza ti abbiamo contattato su Facebook, ricordi? In privato.