How to reset a EZ-guide 250 when it won't start up properly
Пікірлер: 30
@kentwayne84982 жыл бұрын
Thank you for this. I didn't know what the problem was and neither did the dealer. You're a hero!
@johnloewen33122 жыл бұрын
Thank you for the clear guidance in resetting it.
@АюбовМурад6 жыл бұрын
Хоть узнал как сброс сделать,а то ни где не показано! Спасибо!
@itua10168 жыл бұрын
БОльшое спасибо очень помогло в настройке!!!!!!!!
@marcelotela76017 жыл бұрын
Александр Треснитский eu pocuro asfunsau como emtar
@magro91255 жыл бұрын
Не понял ))) в начале ... нашими словами : зажать нижние левые и верхней включить ?
@tomnapier11084 жыл бұрын
ask all the tech people I would find at wimmera field day gps is a write off signs of a problem is it doesnt ask for a field the next problem is cant start and A - B line from what I was told it requires a reduction of stored data which is a soft start by pressing the 3 buttons on the right or the hard start 3 buttons all pushed down on the left which then requires a re install of settings there is a path to find in functions where you can find a place to remove the data seems too much painting of fields is the culprit other than that it would have kept working ok sadly up for a new one hope this helps someone save the unit from a lockout
@philcurulli61903 жыл бұрын
Thanks mate!!
@ДмитроКвітчатий-д7п5 жыл бұрын
very nice man
@amyhofford64376 жыл бұрын
thank you!
@tomnapier11085 жыл бұрын
MIne is showing the New Holland background will scroll the lines across the bottom then a new run of white lines and gets as far as Z blinks off and starts over again done a 3 button start on the right and the lightbar keeps lighting up and moving from one side to the other the tech said it will do this all day if left 3 button restart on left and keeps doing the same bar across the bottom and blinks off and restarts again looks like a trip to dealer to see if they can work out why it was previously doing a lost A to B start for A --- B runs it would keep losing the A to B after a few tries it would finally set the A B line Will add after I find out what went wrong and why it wont restart
@NZCODPLAYER5 жыл бұрын
tom napier you have put it into mon mode so it can have a software upgrade via a computer using flash loader if your getting the lights flashing across the top from memory that means your not holding the power button down as well as the bottom two buttons remove the Power from the back and try running the reset again
@tomnapier11085 жыл бұрын
@@NZCODPLAYER thanks I have tried it all and just can't get it to reset I will take it to warrnambool Monday and let them try I had all the buttons down hard and it won't trip. Auden said press all 3 on the right and just got the lightest working Did a hard reset on the left side and just won't reset There is something else not right as setting an a b line was not going to b. And just kept going back to a. Thanks for the suggestion. Another post online said their mother board was faulty so Monday I will find out. Watch for answers
@NZCODPLAYER5 жыл бұрын
tom napier I have a feeling thinking about it you may have to hold all three down on right to get it back out of monitor mode I can remember off the top of my head and as long as it’s in mon mode you can not do a reset it is normal for it to not to set B point if it is full of data as the display eventually just runs out of room to operate itself I doubt it has motherboard issues
@tomnapier11085 жыл бұрын
@@NZCODPLAYER think that's part of the problems too much in field storage. Strange I can't hard reset
@tomnapier66345 жыл бұрын
@@NZCODPLAYER took it to service tech and he couldnt get it to reset either and you cant go to software part if the main screen is not working I was told so its going to GPS doc to get a look at
@матвейкарабзол5 жыл бұрын
бля а перевод,
@johnloewen33122 жыл бұрын
Thank you for the clear guidance in resetting it.
@euu66 Жыл бұрын
hello, I did it on the my device exactly as you did in the video. the reset worked, but the Portuguese language option disappeared. Can you help me please?