Setting up Multiple Remotes with one Rx -- One Remote with Multiple Boards RF434 4 channel Relay board works on 433MHz frequency.Range is 100 - 150 feet even without line of sight. You can control DC or AC loads using this board.
Пікірлер: 27
@usrrsr2 жыл бұрын
Best ever video on such module among all rest KZbin video
@engr.ziyana.hameed142121 күн бұрын
Explained good, but when the jumper 1 and 2 connected it is working as touggle (touggle mean jumping from one to another) and when the jumper 3 and 4 connected it is working as Latch, so you have said as Latch for touggle and as touggle for latch. Anyways explained the practical good, All the best.
@Techybyker5 ай бұрын
Completely agree with the other comments! Very clear explanation, it's almost a tutorial! Thank you so much sir!
@sensordhanaraj1327 Жыл бұрын
Thank you sir for giving an excellent demo on rf module.
@vk48652 жыл бұрын
Sir, very nice explaination. Speed was very correct for me.. 👍👍
@143streek Жыл бұрын
Excellent, thank you
@anandjoshi8554 Жыл бұрын
100-150 फ़ीट तक काम करता है ? Will it work between rooms with doors open ...about 20-30 feet ?
@deepakh0072 жыл бұрын
Great thing
@akantabauri19628 ай бұрын
Very nice sir ji thank
@mail2mahii Жыл бұрын
Excellent
@dsb4221 Жыл бұрын
Can you pair 1 button of the remote to 2 differnt relays on the same 4 ch board?
@faisalsmz9 ай бұрын
Excellent thanks, i have one without those modes , i need to have it as moment mode, can you help me
@wilfredkandiero98549 ай бұрын
can i connect negative wire on common and positive on NO only for a DC motor
@chennojurahuldev17569 ай бұрын
Can we pass the signal out(N0 pins) from the Rf receiver to arduino uno digital pins? I wanted to control your motor direction using the BTS7060 motor driver(shown in your other tutorial ). Can you please help me out. Thanks in advance
@palanik19602 жыл бұрын
Price and where is it available
@saifuddinsekh20777 ай бұрын
How to RC car control the WiFi relay module
@sanimotovlog5740 Жыл бұрын
Hello sir mene 4 channel kharida hai 2Channel not working Kaise thik kare
@athenazoey50932 жыл бұрын
is there a chance i can combine the momentary with latch mode?
@Praveentricks Жыл бұрын
Yes
@dhruvsharma83158 ай бұрын
How? @@Praveentricks
@joanalonsocastillo4244 Жыл бұрын
hello and how to connect in a car. thanks for your video
@Avinashkumar-om1ji Жыл бұрын
I purchased 4 chanel receiver and transmitter but after connect to load(5 volt led) that light blinks . Is there any problem in receiver. And can i convert momentary switch to toggle mode
@Praveentricks Жыл бұрын
From where u purchased can u provide me link
@kaushalchavan25153 ай бұрын
Can you make it on mobile operator
@mr_pawar_36 ай бұрын
Can i use 9 volt
@mirac.75762 жыл бұрын
hi bro i have a project atmega16 is being used there is hex file but there is no fuse bit setting can you help me