Robot Lawn Mowers Australia - Lawnba E1800/1600 Charge Station Installation

[@stefanlittauer9365]

Great demo, thank you

[@robotlawnmowersaustralia7913]

no worries

[@adamwickerts8680]

Can you guys please make a video how to set up your areas and memory points?? i cant get it to work on my lawn...

[@robotlawnmowersaustralia7913]

.

[@dann_icola]

The application isn't good, bad connection.

[@kevinnelson78]

Hey, I have problems with my lyfco 1750 Wifi, when I select mow it backs out and start cutting along the line around the yard back to the platform and hits the platform, and it turns around and finding the line again and finding it's way back to the platform and hits it again, then it starts over and doing it again, it never begin to cut the hole yard, can the out line be wrong installed?

[@robotlawnmowersaustralia7913]

Hi Kevin, sounds like it is not seeing the power from the charger when it docks the first time. Check you have power at the charging pins. Does the robot charge ok when it is at the charger?

[@kevinnelson78]

It docks to the charger fine, it is from the back side of the charger, it follows the line around then it bumps the charger backside then it starts over and follows the line.

[@robotlawnmowersaustralia7913]

@@kevinnelson78 Oh, that would mean you have set area 1 to a length longer than your preimetre wire. You will need to reset your areas, or just initialze the robot and you should be ok.

[@kevinnelson78]

@@robotlawnmowersaustralia7913 thanks!

[@Risoluoma]

hello! when i start my mower on auto, the mower just backs like 3 dm, and then just start spinning :/ eny tipp?

[@robotlawnmowersaustralia7913]

This might be caused by incorrect polarity of the perimeter wire. Try putting the mower in the middle of the lawn and sending it back home. If the mower does not reach the perimeter wire and follow it back hope then your polarity is most likely back to front.

[@robotlawnmowersaustralia7913]

Sounds like there is no signal from the mower to the charging station, or the polarity of the perimeter wire might be back to front.

[@seabass7030]

I have the same problem with my lyfco. The polarity is right it finds it way back to the charger clockwise. The problem is when it backs out from the charger to trim the edge. It backs out a bit the spins out finds the wire and follows it useally it get stuck in a loop going counter clockwise back to the charger then nod the charger and go around it to find the wire on the otherside and make a new counter clockwise round

[@knulleriboy]

Did you solve it?

[@wodzimierzwojciechowski5314]

Thank you for your very useful explanation. I didn't realise there's such need to so much precision with base installation. The idea of 100mm offset loop on the return wire is very ingenious and really does work. The mower is very good hardware wise but the software looks like it was written by an elementary school student. Have you got any good hints regarding area definition? My mower allows me to define Area #1 and hangs up when I try to define more this is somewhat frustrating since I need at least 2.

[@robotlawnmowersaustralia7913]

Hi, for your area settings. Please try setting the number of areas on the app and then press save, and then press start locating. Then at each location press the start or set location (depending on if you are using the android or IOS app.). The mower will beep if the signal has been received. It will stop when you locate the last area.

[@magnusbragason7101]

@@robotlawnmowersaustralia7913 hi , did you manage to get this working ? I´m having same problem. I activate 4 areas, the click save/send , then click start locating and mower backs out of charger, and turns around and starts going anti clockwise. When I choose click start locating again it says locating area 2 and so on, until I choose area 4. But then it seems as if nothing has registered ! And it doesnt say its finished ! Somethings missing... Ive tried like 20 times .... getting tired ;)

[@federicaannunziata3991]

buongiorno, ho provato in tutti i modi ma in automatico non funziona non esce dalla base e anche se lo metto al centro del quadrato non si muove. Non parte in automatico ne dall'app ne se premo il tasto sul robot e non torna neanche alla base. AIUTOOOOOO

[@robotlawnmowersaustralia7913]

.