Reelsteady Go or Hypersmooth 2.0 for FPV? | GoPro Hero 8

#reesteadygo #hypersmooth2.0 #FPV
I wanted to test if reelsteady looked better than hypersmooth 2.0 on an FPV. The reason I bought a hero 8 in the first place was because I thought Hypersmooth would be able to stabilize it well enough without any external software. It does a good job but reelsteady go is just better. Reelsteady go is only 100 bucks so its not too bad. You get a free watermarked trial if you want to give it a shot before buying. It's still pretty new, but I am loving my Xhover Blastr.
Check out my other pages:
/ rogie_films
/ rogiefilms
rogiefilms.com/

[@ScoutFPV]

Nice vid man thanks for the info. Was thinking on getting the hero 8 so i could try using real steady. Is the hero 8 worth the upgrade from hero 7 black?

[@RogieFilms]

Thanks! You should be able to use your hero 7 with real steady. So I would stick with that and see if you like the results before you grab an 8.

[@ScoutFPV]

@@RogieFilms I tried with the 7 but just couldn't get it to work properly a lot of shakes. I was reading that the 7 was one of the gopro's that the gyro data doesn't work well with real steady

[@ScoutFPV]

@@RogieFilms Mind you i just had the trial version maybe there is a differance with the full version?

[@RogieFilms]

@@ScoutFPV that could be! No complaints with the 8. Works really well especially on the newest update

[@samuelfrench9665]

Linear or wide? Also why not do hypeesmooth with boost work reelsteady?

[@RogieFilms]

Learned a bit since I made this but if you shoot in 4k 4:3 aspect ration on the GoPro you get the best quality. Hyper smooth and reelsteady both use the gopros gyro. When u use hypersmooth it takes away the gyro for reelsteady to analyze. Hope that helps lol

[@samuelfrench9665]

@@RogieFilms thank you! if you record in 4:3 then how dies it know what is on the sides for when it turns to 16x9? or is it just taking the top and bottom out of the 4x3?

[@RogieFilms]

@@samuelfrench9665 real steady always crops in a little but when you shoot it in 4:3 it crops it to 16x9

[@samuelfrench9665]

@@RogieFilms but would that just be zooming in on the image then which would make quality worse than just shooting in 16x9? Just trying to understand it better. Thank you!

[@RogieFilms]

@@samuelfrench9665 yeah that’s correct. But when you shoot in 4k you wouldn’t notice much quality loss

[@EMDRONES]

Can you use hypersmooth2.0 on and still use RSgo or turn off hyper smooth to be able to use in RSgo?

[@RogieFilms]

Pretty sure you gotta have hypersmooth off to use RS

[@RogieFilms]

What do you think of the flight at the end?

[@Mekanikern]

What resolution is this recorded and rendered in? It may be the youtube bitrate that blures it, but it seems to have altered resolution or low bit rate.

[@RogieFilms]

Doesn’t look blurry to me mate its 4k and rendered in 4k at 100mbps

[@Mekanikern]

Good, then it’s probably just youtube cheaping me off. Looking forward to testing Reelsteady on my 6.

[@RogieFilms]

Mekanikern the newest update for RS is very good make sure you’re on the latest

[@Mekanikern]

@@RogieFilms I just bought it so it should be fine. Now it's just about finding time to use it.

[@tommcmannfilms]

Reelsteady definitely just has this look that HyperSmooth can’t match. Were you running the hero 8 hard mounted on your drone or did you use one of those 3D printed soft mounts you have you use for the hero 7 & 5?

[@RogieFilms]

It's hard mounted to the drone. I'm finding that using less stabilization points (1 or 2) seems to produce better results.

[@tommcmannfilms]

Rogie Films good to know. I wasn’t having much luck with the hero 7 and ReelSteady go (even with the soft mount). I just picked up the hero 8 and will be testing it out soon.