rollergirlskate... RGS' Jesse McNasty walks you through simple mounting directions. Copyright RollerGirlSkates
Пікірлер: 78
@JoJoMaMa_4 жыл бұрын
I broke my toe the other day so I obviously won’t be skating for a little while- so I’m watching all the skate videos I can 😆 This side of skating is pretty interesting. Even though this video was posted a long time ago.. thank you! ✌🏼
@sstatic60934 жыл бұрын
There's lots a videos out on that, what about changing your plate but using the same boot so the plate is different than the original plate though.
@anam45643 жыл бұрын
What drill bit size do you use?
@jeffgoggin13942 жыл бұрын
This was a great video tutorial! Thank you so much for taking the time to post it!
@ZteveW2 жыл бұрын
How would you center it if you didn't have that tool?
@my_dear_friend_10 жыл бұрын
You seem to mount to the center line of the boot but not to the center of the foot as suggested in other places. Why?
@zoebenfield53939 жыл бұрын
Good video! I tend to build the plate up, just to make sure that the wheel balance is right on both boots, as well as being symmetrical for both boots. I would also add that while the snyder tool is a great thing to have, it is not perfect every time, and double checking is a good idea.
@Thequadchannel3 жыл бұрын
agree
@flexiland67412 жыл бұрын
Thanks, so many great tips in a single video!
@BucketCharlie4 жыл бұрын
I bought boots and plates seperately, so this is helpful.
@stephaniemorales62634 жыл бұрын
This video makes it look so easy, I really want to buy new plates for my skates......I might try it....ahhh I think i'm gonna do it!
@chelsealadd333 жыл бұрын
me too! did you end up doing it? if so, how did it go?
@kevinpelcat172710 ай бұрын
Super vidéo, elle est claire et précise, elle me sera très utile lorsque je vais changer ma platine Merci beaucoup
@williammuff54852 жыл бұрын
what if you don't have that tool for centering?
@queercomputer3 жыл бұрын
This was so helpful. Excellent work.
@jasonnicholasschwarz77883 жыл бұрын
What if the boots are boots with heels? Do I drill through all of the heel (which is kind of high, like in a figurekating boot)? cant I just screw them on?
@donanders21106 ай бұрын
Yes all the way through!
@asb15836 жыл бұрын
Is the plate aligned with the center line straight down the middle of the plate? Watched a couple videos and it looks like there is an offset aligning method. Want to have it correct before i start drilling holes.
@rollerskater3 жыл бұрын
The centerline is the point you depart from on a typical skate mount; I’ve never seen a professional mount to the centerline, always the toe end of the plate is moved more towards the outside by a small amount. The heel side stays the same, though.
@SoCalSh0w Жыл бұрын
Hi, this is actually one of the best videos I've seen of a plate installation, of the nearly dozen I've watched. May I ask where you got the tool to break the bolts, and what kind of metal/bolts those were? I tried stainless, and that could not be bent like that, haha. Youre also the only one to use washers betweem the plate and keps nuts, and I wish I came across your video for that first, to avoid the scuffs on the plate.
@RoastedMarshmelon Жыл бұрын
That was really interesting! I was recently wondering if it was possible to remove the plate to clean up underneath... but I had no idea how it was even mounted!
@donanders21106 ай бұрын
Some lower end skates have the plate riveted on! But if bolted you can remove them!
@vmexplorer2 жыл бұрын
Great Video! Thanks for posting this!
@VeeBee812 жыл бұрын
Its so difficult to find a skate shop that does maintenance in London. I’m wondering if my cobbler has any experience? What type of screwdriver was that?
@joshmaster618 Жыл бұрын
So you you mount skate plates. So what is the definition of sport mounting a skate plate? Do you move forward a few Millimeters?
@donanders21106 ай бұрын
I have seen many people that shoot short screws through the plate into the sole! Then remove them and the holes are marked and somewhat predrilled as well!
@TruthInBeauty3 жыл бұрын
7 years later and this is so helpful!
@vinztheoriginal3 жыл бұрын
It isnt. It's not how you mount a plate. You can't put a plate on a boot without the foot of the person who will wear it. As everyone has a different foot you have to mark on the boot the 2 pressure points of the person foot. Then look at the axles distance, choose the right plate and then align the 2 axle with the marked pressure point of the foot.
@RoastedMarshmelon Жыл бұрын
@@vinztheoriginal Kinda like when I ordered my roller skates from Rollergirl. Or when I got ice skates. In both cases, I told them my ankles have an inward weakness, and so they put the plate a bit off center for me. In the case of Rollergirl, they did it from a distance only with the measurements I sent... I don't know how they did it, but I've had them for 11 years now and it seems they got the placement right. (Also it will be less noticeable on quad wheels than on a thin blade...)
@the63rd11 жыл бұрын
What would be a good way to center a plate if a Snyder marking tool is not available
@prestachuck28673 жыл бұрын
Measure across the widest point of the boot in mm and mark the halfway point, then measure across the center of the heel and mark the halfway point. Double check your measurements. Then align one edge of a ruler or straight edge with both marks and draw a line that passes directly through both marks from front to back edge of the boot. Now you have a traditional center line.
@Thequadchannel3 жыл бұрын
@@prestachuck2867 that is a starting point yes.
@williammuff54852 жыл бұрын
@@prestachuck2867 What are the "rules" for centering front to back? I have read there are different types of mounts, but is standard just (centered)? I have a 8 Riedell boot and it recommends a 675 powertrac, just curious.
@michaels8607 Жыл бұрын
cool...where are you?
@samehdarawshi35373 жыл бұрын
thank you. any reason i find some videos using only screws from outside where in some i see as here bolt from inside and washer form outside? sure bolt and washer are stronger and wont snap but would be interesting to know if in certain conditions you can use screws.
@ATSaale2 жыл бұрын
I've done skates where I put t-nuts inside the boot and machine screws from the bottom of the plate to the t-nut to mount plates.
@donanders21106 ай бұрын
Some peolpe will shoot screws through the plate to mark the holes! Then remove and drill for bolts!
@SeattleRingHunter10 жыл бұрын
Why not 1/4" towed in from the center line at the ball of the foot?
@Dobemandan5 жыл бұрын
Right!
@HomeandYacht2 жыл бұрын
What is that centering tool called?
@Band0Brand07 ай бұрын
To me the break off tool is the most animalistic way of doing it! I use a Dremel with a 3/8 metal cut off wheel an I bring it down flush with the Kep nut!!
@mshomefire7 жыл бұрын
great exit
@reptilesxo21924 жыл бұрын
If we don’t have the room to find the center line, how can we find it?
@rogerdecosta29855 жыл бұрын
What happens if you don't have the mounting plate thing how do you keep the plates straight
@V.Z.692 жыл бұрын
0:42 I just watched an old timer skate guy use this tool, and he said to slant the tool with the curve. Where you are slanting opposite the curve of the boot. at this time here kzbin.info/www/bejne/lam5gZVppLt2ma8 Discusses this point here: kzbin.info/www/bejne/lam5gZVppLt2ma8
@lucilachavez21273 жыл бұрын
what's the machine called? where can I purchase one?
@dennisfountain79252 жыл бұрын
Great video nice boot where do you buy?
@omarchacon28862 жыл бұрын
Hi,are the plates the same size as the boots? If I have a size 10 boots should I get size 10 plates ?
@gerbil47672 жыл бұрын
It depends on each plate company. They'll have a sizing chart you can go by typically.
@Shellzwick3 жыл бұрын
What to do if you already have a boot with holes but they don't line up . How do you work around pre-existing holes
@ATSaale2 жыл бұрын
Ignore the old holes and drill new holes. Best practice would be to fill the old holes first, but I've remounted boots without doing that and it didn't cause any issues.
@lucilachavez21273 жыл бұрын
What are the exact tools that you used???
@Isabelle3.149 жыл бұрын
8:38 What's the name of this tool? I need one like this. :P
@ASMR_Brittneylynn5 жыл бұрын
Isabelle-Blanche TM it called a bolt break off tool
@American_Made2 жыл бұрын
What kind of boots are those?
@charlessmith65462 жыл бұрын
Why u did not put a flat plate n side the boot
@theantiprepper71219 жыл бұрын
wonderful...what makes you think everyone has that tool? :(
@ASMR_Brittneylynn5 жыл бұрын
What is that bolt bender thing called????
@towdjumper5 Жыл бұрын
Great stuff.
@jerryhelm5118 Жыл бұрын
Great video thank you..
@semonethomas63073 жыл бұрын
Dude!! I came across your video which is AWESOME!!!! ALTHOUGH YOU DID WORK ON INLINE SKATE, MY QUESTION IS CAN THE SAME FOR BEGINNER'S QUAD SKATES. I HAVE A PAIR OF OL AS BUTT SMUT KMART SKATES WHICH I'M HOPING TO REMOVE THE BOOTS AND SAVAGE THE TRUCK PLATES AND WHEELS. I HAPPEN TO REMOVE THE INSOLE AND FOUND THE BOOTS ARE RIBBIT STAPLED TO THE PLATES!!! CRAP I MIGHT BE STUCK! YOUR VIDEO IS GREAT....SPECIALLY THE ENDING😂😂😂😂😂😂LOVE IT.
@AIMORAN6 ай бұрын
Go. I'm not the. person that posted this video. I have been mounting roller skates for a long, long time. One of the things I think he missed is that you can also square the plate with the same Snyder mounting tool. and two that is not an inline skate plate. It is a quad plate. Great. video. Thank you.
@chelsealadd333 жыл бұрын
great video, thank you
@sandb18677 ай бұрын
Why no Lotite?
@chphoto86954 жыл бұрын
Can I video call u to see if my plates are mounted ok?
awe! the website doesnt exist anymore. theres rollergirl.ca but i dont think its the same people. skating is exploding right now, youd think theyd be in business. thats a shame i hope everything is ok with the owners. thanks for the tutorial
@bunsomite3 жыл бұрын
Awesomeness
@Thequadchannel3 жыл бұрын
wow, just watched this and sooooo many things left out. Very little explanation about what or why you are doing things.
@Band0Brand08 ай бұрын
Damn too bad I can’t buy those boots😢 such a shame. They where just too good
@jbotnik3 жыл бұрын
That exit 🤣🤣🤣
@vectortiedye2 жыл бұрын
Has anyone else gotten a deformed pair of Riedell skate boots ?
@krisc35433 жыл бұрын
D
@birdfriday3 жыл бұрын
What do you call the bolt bender/breaker and where do you get it?