Issue was throttle body adaption after disconnecting of battery in a 1999 VW Passat wagon. Today is Oct 2, 2020 I ordered the Hex-V2 a week ago, it arrived in the mail this afternoon. I downloaded software and connected everything and followed the steps in this video. It recognized the fault in the throttle body and took me through step by step to readapt. Was back up and running in about 5 min! Then took some time to go through and clear other codes. Thanks Ross- Tech!
@ughblenders Жыл бұрын
having this issue with exactly that car. did you have to buy the $99 registered software key or were you able to do it without?
@juneaufabrellos Жыл бұрын
@@ughblenders I believe I bought the $199 Hex-V2 version that lets you work on up to three vin car numbers. By the way, the older cars it doesn’t register a vin in the system, so you get more wiggle room depending on the number of cars your working on. As I said in my post, i downloaded the software, hooked it up and had the throttle body issue cleared up in just a few minutes. Hope it works for you!
@juneaufabrellos Жыл бұрын
@@ughblenders I called them to order and the tech that took my call was very helpful
@ughblenders Жыл бұрын
@@juneaufabrellos bought mine off of Amazon so when I reached out for my activation code they told me it wasn't through a verified seller. Guess I'll pay the $99 for the software bypass! Thanks, appreciate it 🤝
@nathangates19677 ай бұрын
Srry how do I get this system does it come with the cable to hook up to car or can I buy the whole computer and everything somewhere I know it'll be helpful for other cars as well
@ChristosSelman9 жыл бұрын
Great video. Did this the other week but I forgot to check the battery voltage, the TBA solved my problems for 2 days but the problem came back. I forgot to check the battery Voltage, what happens if the voltage is not over the limit 11,5-11,9 V?
@RossTechVCDS11 жыл бұрын
Then you wait more than 30 seconds. :) I'm not really sure why the 30 second rule is there in the first place. From our point of view (VCDS), nothing happens between the ECM and VCDS after the ADP OK message comes up. The EPROM does need to save new values from the Throttle Body, but I would think that takes 30 seconds to happen, as in milliseconds. But the 30 second rule comes from VW / Audi, so I'm sure there is some reason for it.
@joachimjohan12155 жыл бұрын
my 1.8t aeb 1998 drive by cable runs the group 98 adapt over and over again, it wont stop. looks like in the video but after like 8 seconds it starts again... no codes. only a climbing idle speed from 900-1250rpm, hot and cold. this is after cleaning and ecu was unplugged. Thanks!
@user-ld2ph8bp2p3 жыл бұрын
Please help me. I'm Japanese. 2010 Model VW New Beetle ABA-9CBFS Group 98 does not show up at 1:27 "ADP,OK" does not appear on the right side of the screen even after "060". Top left Lebel file is displayed as "none"
@bagarbagar21035 күн бұрын
I want to do adaptation in vw golf 6 cayc, after pressing it appears stopped, how to do throttle adaptation?
@altacombustao_oficial3 жыл бұрын
hello, in my module do not use this option in the basic settlings menu. My model is UDS
@YourFavouriteComment7 ай бұрын
Awesome fixed my startup issues in cold weather
@attilafekete61772 жыл бұрын
I was trying to calibrate my throttle body in my audi a4b7 (8E) 2005 but i don't have any of these options. Protocol says CAN, there's no channel 098 or 060 and in the drop menu there's only EGR, boost pressure and Fuel pump. Can i get a bit of help?
@jukehallman Жыл бұрын
Diesel engines don't have a TB
@HAM-CU7BE5 ай бұрын
Hi. I have a Seat ibiza 1.4 TSi 6j cupra, BocaNegrA version with 180hp. Original. I m doing the replacement of that throttle. But I also have to replace the other one behind . Exactly behind of that black plastic throttle, theres another metal throttle. So How can I differentiate the alignment from the plastic throttle to the metal throttle with VCDS and vagcom??
@COSMOESTEREO8 жыл бұрын
Great video thanx RossTechVCDS , my golf mk4 alive again.
@fillduffman Жыл бұрын
Waiting 30 seconds after basic setting has finished, is this a must, as I've always just stopped 😳 and ended
@JohnODonovan18 жыл бұрын
can anyone direct me to an updated version of this procedure. with my hex net all I see is COMMON and no ADVANCED settings. I can't get into the throttle body. thanks
@ThatGuy-vi8ch2 жыл бұрын
I have a 2019 VW GTI SE and I changed my battery. The cruise control didn't work right away, didn't think about it on a stick shift. I parked, turned it off, turned it on but not start, waited for 5 minutes, turned it off, started the car and suddenly I had my cruise control back. I have no idea why, just sharing my experience with this model VW.
@blkcoupequattro Жыл бұрын
I was under the impression you can do this without VCDS, supposedly you turn the key on hold the gas pedal to the floor for 5 seconds, then switch the key off then release the gas pedal the alignment takes place by itself over the next few seconds with the key off...
@Knightguyver11 ай бұрын
I also thought that, but my 1998 aba is still having idle bouncing/surging issues. So I’m hoping this will fix it
@andreabiondi82510 ай бұрын
Good morning, I installed the new EGR valve and the new throttle body, do I need to alignment them? I reset the error and it didn't reappear, the machine seems fine. Golf 5 2004 2.0 tdi 16v 103kw Bkd.
@fizumi1h1 Жыл бұрын
ADP RUN does not appear on AEE,AFT how do i know if it's been complete?
@PVflying5 жыл бұрын
What's the reason for waiting 30 seconds before clicking the stop button?
@fernandoc89486 жыл бұрын
Hola it's works in a A4 TDI 2.0 2008 B8 ? My car has this valve
@MrHacsek114 жыл бұрын
What does the adaptation step counter mean? Sometimes my car has 6 or 8.
@masnidaniel7 жыл бұрын
how check oil pressure.please help me.
@RossTechVCDS10 жыл бұрын
Please contact our support team, you will find our email address when you click the [About] button in VCDS. Be sure to include a full Auto-Scan.
@mdrc3288 Жыл бұрын
Should an alignment of the EGR valve follow an alignment of the throttle body?
@RossTechVCDS11 жыл бұрын
Did you have the battery disconnected? If so, then doing the TBA can resolve that issue. The high pitch noise... throttle bodies are known to do this, it can be considered normal in most cases.
@ahmirnolan77313 жыл бұрын
You all prolly dont care but does any of you know of a trick to log back into an Instagram account? I was stupid forgot my account password. I love any tricks you can offer me
@ahmirnolan77313 жыл бұрын
@Waylon Bruno Thanks so much for your reply. I got to the site on google and im trying it out now. Looks like it's gonna take a while so I will get back to you later with my results.
@ahmirnolan77313 жыл бұрын
@Waylon Bruno it worked and I actually got access to my account again. Im so happy! Thanks so much, you really help me out :D
@waylonbruno89123 жыл бұрын
@Ahmir Nolan Glad I could help :)
@3bbad2 жыл бұрын
Hi, could someone help me please. In Result Throttle Valve ADP. I get [ 00 ]. I have tried all groeps 060, 098 & non usd.
@tazgamerplays3 жыл бұрын
On mine, instead of showing adp ok it says error. I have checked the relay by the computer and it seems fine also.
@azzz80832 жыл бұрын
did you find a reason? I saw one today with the same issue
@tazgamerplays2 жыл бұрын
Mine had a bad engine temperature sensor. Basically the car thought it was extremely cold but it was in the summer time. I'm not sure if that was the causing the error though. Did get the car running again, at least for a few months. It did the same thing again and no matter what we did, we never did get it started again.
@azzz80832 жыл бұрын
@@tazgamerplays seems like there are different kind of throttle bodies, check vcds website and they say how to adjust each one of the three kinds. There’s a video from their official channel, probably you need to run a full on-off time to get it to adjust
@tazgamerplays2 жыл бұрын
@@azzz8083 We ended up just junking the car. We started having other issues. The back driver side door had a short somewhere, the front passenger window mechanism broke, an exhaust leak started after getting it running. We didn't want to put the money into it.
@gwadaflat2 жыл бұрын
Hello , Hello, I bought my VCDS from Rosstech France and I would like to know the procedure for aligning a new throttle body and at the same time, take the opportunity to clean the intake manifold, on my Vw Passat B6 variant 2.0 L TDI 170cv, can you help me please? Thanks a lot ! 👍🏽
@alexandrefelippe2 жыл бұрын
I'm trying to perform the thottle body adaptation on my Brazilian VW UP TSI using the new VCDS version V22.3.1 for win11 but I can't find the option anywere! Maybe they removed this option from this version or changed the option to another place?
@RossTechVCDS2 жыл бұрын
We are not removing things from the software. But different vehicles can have different variations of how to do a given task. We offer free vehicle support on our web forum for our registered customers, post there for further support. forums.ross-tech.com
@alexandrefelippe11 ай бұрын
@dreadwings3 I found the opinion to perform the throttle body alignment on the newest vcds version, which is on a very different location. Will need to re- learn how to use vcds because they changed things place. Regarding if I could manage to perform throttle body alignment, the answer is I am not sure because at old version v12, we can listen to the throttle body working (the characteristic noise) with the newest version the throttle body simple do nothing. The characteristic noise is not present. Therefore, I am not sure if it's working properly or not.
@unaibilbao52222 жыл бұрын
hello, I have a P1581 fault code on A8 2005 ASB motor (V6TDI). I´m lookingo to know de basic setting channel of the J338 (throtle body). Do you know the number of the channel? thak you guys!
@RossTechVCDS11 жыл бұрын
The shareware version doesn't support Basic Settings. But when you purchase the full version, then yes, it is possible to do a Throttle Body Alignment.
@MrJT13693 жыл бұрын
what is the full version? i sepnt $270 on a VCDS scanner mainly to do a TBA and i have the downloaded file from the 20.12.0 release how do i know if i have the full version or not?
@vcdsbyrosstech3 жыл бұрын
@@MrJT1369 If you purchased from our web site or one of our distributors, then you have the full version.
@mrlntejada6 жыл бұрын
1999 audi A4 1.8t Vcds lite 1.2 I’m getting message Too many communications errors to continue How can i fix it ?
@MrConnina5 жыл бұрын
it's valid for audi 2000 tdi 8e/b7 valve?
@S4_QUATTROPOWER4 жыл бұрын
Would this cause P0300, and misfires on cylinders? I have disconnected the battery when rewiring coils clips..
@ilikefishing78583 жыл бұрын
sorry off topic. is there a way to get the original module coding from either the car or audi? can change myself after buying your unlimited vins hex v2.👍🇬🇧
@pokey420011 жыл бұрын
My 98 beetle is stalling out after doing a valve cover basket install and i can hear it making that high pitch noise. Should i be looking into doing this?
@MichaelConroy248 жыл бұрын
When I do the reading, I'm getting 15.69 and 84.10 and then it goes to 12.94% and 87.84 when it read adp ok. Is this normal? I have a 07 a4 3.2
@dansolo99787 жыл бұрын
Will this S/W work with an EBay ELM327 OBDII Please..? Also What is My 02 A3 1.8 20v SE - None UDS or UDS DBWire..?
@vantripper_pt87tiagovitori4111 жыл бұрын
Hello. I can´t do the Throttle Body Alignment. The car is a Golf V 1.4 FSI 2004 and appear "Error" on Group 60 in Basics settings. I already change the throttle body, ecu and check the wiring. I think that the problem is the lambda sensor. The dtc is "Adaptation not started". Please help. Thanks (sorry my english)
@NachoBides6 жыл бұрын
Is there a way to adjust idle speed on a polo 1.4 bby with a 4mv ecu? Thanks
@ehabmahroos1694 жыл бұрын
Skoda Octavia 2011 wich one of the 3 types ?
@proverbsuche61416 жыл бұрын
had a melted starting coil that affected my ecm I had it changed, now my car won't rev above 1000rpm
@ibo11377 жыл бұрын
Why and when should you do this alignment? If i take off my throttle body to clean it, do i have to do this? I got an Seat Ibiza
@marcior.21533 жыл бұрын
when throttle response is bad i believe. Like a delay for example.
@fernandoct66 жыл бұрын
funciona en un vw touareg 2008 TDI?? does it work in a vw touareg 2008 TDI???
@olekristiansolli177810 жыл бұрын
Hi! I have the Drive By Wire version om my audi a3 1.6, but when i try this (060) the result throttle adj. It just say's "locked" do you know why?
@BalticMotorSport7 жыл бұрын
Why does mine shows "adaptation value - error" in the last box, when I go to channel 060? 2000 Audi S8. Ignition on, engine isn't running. VCDS Lite 1.2 full.
@killerkittenz49775 жыл бұрын
I'm having the same problem
@markmangano17313 жыл бұрын
Thank you for this great video mark mangano dependable auto wartburg tennessee outstanding video
@thynehi9415 жыл бұрын
Is this fuction can perform from vcds lite?
@N-e.o4 жыл бұрын
i cant acces basic settings or measuring blocks everything is greyed out except for Fault Codes" I can check and reset Fault Codes but how do i acces Engine measuring Blocks?????
@RossTechVCDS4 жыл бұрын
We offer free vehicle tech support for our customers on our forum. forums.ross-tech.com
@KorashSyndikat Жыл бұрын
Sadly my 1,8T AGU kesps throwing a P1559 - 35 - 00 failure code. Basic settings arent possible to set up. The Adaption always stops. I already got a new Throttlebody, still the same error. Anyone has a clue.
@RossTechVCDS Жыл бұрын
We offer free tech support on our forum for our customers: forums.ross-tech.com
@webpro607Ай бұрын
I can't find this setting in VCDS! my car engine is CAYC
@RossTechVCDSАй бұрын
CAYC..... kzbin.info/www/bejne/aKvVnpt6rMSpbbs
@nac500012 жыл бұрын
very good information thanks!!!
@MacioTheKilla4 жыл бұрын
Error group 060 not available :(
@Venenooffroad11 ай бұрын
Nice tips! Thanks..
@edapl8985 жыл бұрын
Does anybody know if it works with Golf GTI mk3?
@monsef19543 жыл бұрын
Hello,, After replacement of the fuel level sensor in my touareg 2011 / 7P . If the fuel lamp still on and the meter reading still zero .what can i expect . Thank you.
@habibpallath Жыл бұрын
Check the connectors properly fixed..I had the same issue before..Opened again flange and removed the connector and refixed back..problem solved
@Andrey119988996 жыл бұрын
Hello i buy vcds 17,1 limited version cannot update, my problem is when i use measures blocks if i use more then one, i mean 001 and 002 its jump between and do not available 1 sec available another time not / yes what is the problem can be?
@RossTechVCDS6 жыл бұрын
email our support department: www.ross-tech.com/contact.php
@DL-by4tq7 жыл бұрын
hi sorry about this. but i do have a BMN engine code audi A3 170BHP tdi and it does have a throttle body. what did you mean ''diesel don't have throttle body''?
@____________63246 жыл бұрын
means diesel cars does not need any air. :D :D
@mrrobertwolfiii1079 Жыл бұрын
Crank and head is Right, transmission saved in pouring down rain fluid right, not diesel found it gas, got the job of read that's. Han nes bag box and battery goes out about as expected. Dec 25 2022
@tomasbranda7714 Жыл бұрын
Thank you
@sacheus11 жыл бұрын
HI. can you do this with VCDS-LITE?
@heanstone13273 жыл бұрын
No
@You.Cant.Fix.Stupid Жыл бұрын
Thank you!
@bashirisah75447 жыл бұрын
I have golf fsi 2004 it has raising problem
@RobertMorodan3 жыл бұрын
Hi, do i need to do something similar to the EGR valve if i changed it? Thanks
@RobertMorodan3 жыл бұрын
@@johnsantos6948 i have replaced the egr with a new one and i received after 4000km insificient flow from egr. Is it already faulty? Should i replace it again?
@RobertMorodan3 жыл бұрын
@@johnsantos6948 when I replaced the egr, i also replaced the throttle body. They were both new. But egr keeps giving error p0401 egr a flow insufficient detected
@RobertMorodan3 жыл бұрын
@@johnsantos6948 i have an aftermarket one for egr, and original for TB
@RobertMorodan3 жыл бұрын
@@johnsantos6948 what do you mean "swap"? Replace it?
@StrEagle11 жыл бұрын
what if you wait more than 30sec?
@tzotzobenos17885 жыл бұрын
how to select protocol ??
@loki-us1jd4 жыл бұрын
i cant get rid of the error
@Obotoboteso10 жыл бұрын
I have VW Passat 2000model 1.8T.\ the engine will go off shortly after I start. and at a time it will not even start what is the cause?
@Toschomacher10 жыл бұрын
The immobilizer is cutting the engine off I guess? Have you changed the key and missed to program the new key?
@jamesburfitt82197 жыл бұрын
Hi, I had my door electrics messed with on vcds. now my window switches work opposite to what they should also the wing mirror swich is opposite. any idea how I can sort this? I have vcds so can access the systems. many thanks
@ali1t2 жыл бұрын
You probably have the coding for LHD vehicles, you'll likely need to either change through the hidden menu or by changing through vcds, although be careful not to incorrectly code as you can cause permanent damage to expensive modules.
@diazhen12 жыл бұрын
Gracias
@chino8888810 жыл бұрын
I have a vagcom cable, I got a engine fault for intake manifold sensor flap fault, I had the flaps sensor changed and I still get the same fault for sensor position flap, I ha r a tdi diesel mk5 jetta and was told that a diesel has no throttle body my engine is cjaa so I tried to adjuat the flaps in vagcom I get a error any suggestions thanks
@RossTechVCDS10 жыл бұрын
At the 4:00 mark in the video it is stated that that diesels do not have a throttle body, so the details in this video would not apply. If you need further assistance, contact Ross Tech by email, you will find our email address when you click on the [About] button from the first screen of VCDS. Regards.
@Dario-bl1ww7 жыл бұрын
I have an Audi tt 225 what kind of throttle does it have
@uiolkijhgh7 жыл бұрын
Same here i have a 225 also
@MrLoyalss6 жыл бұрын
non uds ecm
@hernandezjosefelipe7 жыл бұрын
where can I get this software I have a 1999 Volkswagen Passat
@RossTechVCDS7 жыл бұрын
store.ross-tech.com/shop/cat/VCDS.html
@santos94648 жыл бұрын
Someone try this on a 1.8t 20v AGU (motorcode) ??? Thanks people
@szalasizsolt719 жыл бұрын
Hey guys. Can someone tell me if I can use this program VCDS and the diagnose cable with a tablet? Thanks
@RossTechVCDS9 жыл бұрын
Szalasi Zsolt Depends. Our wired interfaces can be used with the Windows 8 tablets. You can find them for under $100 for the 7" and 8" versions. They often have a micro-USB port, so an adapter would be needed. Our HEX-NET wifi interface comes with VCDS-Mobile. VCDS-Mobile works with Android and Apple devices. Search our Ross-Tech.com website for "HEX NET" to learn more.
@szalasizsolt719 жыл бұрын
The thing is I already have an interface (Hex-Can 12.12 with usb connection cable) and I wanted to know if it could be used with the Android tablets, but I realized that it's not worth complicating things, I'm gona buy a notebook and that should do it. Thanks for the info anyway! P.S. I tested my car the other day, wanted to know if I have any error codes , and after the full scan I started the engine and wanted to see the real time functions (measuring blocks) and surprise .. any number I picked in the measurings groups it wrote N/A and some error ... I don't recall anymore what it was. What could do that kind of errors?
@Mathewmartialart8 жыл бұрын
+Szalasi Zsolt i have the lynx tablet and works fine on the wind 8.1 i do however have both authentic uk vcds and the rosstech software
@lemansautomotrizyproscaner78188 жыл бұрын
for GOLF YEAR 97? WHAT CODE IS.
@mrrobertwolfiii10798 ай бұрын
S what I got finally cables. Drive by wire.
@MJAfifi10 жыл бұрын
Am I the only one who noticed 4:00 ??
@LY5AT10 жыл бұрын
lol, what the hell
@MazwiZwane10 жыл бұрын
woah!! thats a meme over there. lol
@nforce4009 жыл бұрын
+Mohammad Afifi yeah, a trollface xD
@haidumartocianliviualin46317 жыл бұрын
noticed what ?
@BOHICA_5 жыл бұрын
@@haidumartocianliviualin4631 "thorttle body"
@m.eduardogonzalez925111 жыл бұрын
Hola, funciona para un Audi A4 2.0 TFSI 2007?
@S4_QUATTROPOWER4 жыл бұрын
Simón lo acábo de hacer en mi Audi a4 2.0t Quattro 2010
@santos94648 жыл бұрын
4.0 dosnt work on audi a3 1.8t agu
@todortodorov36346 жыл бұрын
I`m with the SIMOS computer and it can`t adapt itself...
@kennethbeeler13 жыл бұрын
So now that I know my 2006 TDI has no Throttle-body, how do I use my RTech software to get my car out of Anti-theft mode? I changed the ignition components except Key housing/ chip reader. Car starts the shuts off ?
@b5Bart2 жыл бұрын
What do you mean it has no throttle body? Of course it does
@MaximusLX2 жыл бұрын
@@b5Bart Diesel engines don't have throttle bodies
@RossTechVCDS11 жыл бұрын
Sí, el mexicano New Beetle es compatible. Contamos con un distribuidor en México, puede ser alcanzado en cesar.macias AT gmx.net
@123kaidos11 жыл бұрын
good info
@armandsfelkers19837 жыл бұрын
tank you, info :)
@ThedxRAMPAGExb6 жыл бұрын
does this work with fords too?
@DrDodge246 жыл бұрын
Is Ford made by Volkswagen? No.
@RancidJAx6 жыл бұрын
Can i do this with the free version?
@RossTechVCDS6 жыл бұрын
No, the shareware version of VCDS-Lite does not allow for Basic Settings.
@RancidJAx6 жыл бұрын
Thanks for the reply.. I might buy a license
@shanedude1205 жыл бұрын
I am sick of these measurement blocks.the newer vcds doesn't have the measuring block option. its grayed out. and all these videos are using measuring blocks
No, definitely not! VCDS only works with cars from the Volkswagen Group.
@khan209i7 жыл бұрын
you need Hondata flashpro
@sybrenvanheeswyck11 жыл бұрын
HAHHAAHAH Loved the troll image :D
@Fraddy913 жыл бұрын
On the most diesel cars since ~2005 there is electric throttle...
@roberthart72374 жыл бұрын
crap dont tell you that you have to pay about ninty pounds befor you can use it
@bradbozarth46352 жыл бұрын
Okay can we start with, HOW TO HOOK THE CAR UP lol
@Chrishuff17 жыл бұрын
4:03 "There is no "Thorttle Body" haha
@398161657 жыл бұрын
Audi
@comgreed2 жыл бұрын
Tag: foot blisters ok this is weird 🤔
@gratigo110 жыл бұрын
My mechanic was going to charge me $75 for this!
@Mathewmartialart8 жыл бұрын
+jensen chase its not surprising considering these things aitn cheap, so they have to make their money back (obviously they are also using up their time to press buttons but also go further into doing some physical diagnostics afterwards
@killerkittenz49776 жыл бұрын
@@Mathewmartialart my dealership was going to charge me $500 to test a good throttle body then even more just to have it replaced and labor on top of that, I decided to do it and it only cost me $60 and 3 afternoons also one of the damned hex bolts holding the throttle body on was torqued down way too much and stripped out, then I had to take out the intake manifold luckily I have a mechanic who allows me to use his shop and tools to fix my cars, although I would consider my Audi more of a nightmare than a car XD
@nealmaha78895 жыл бұрын
thats cheap. do you work for free?
@ra366810 жыл бұрын
Hahaha, You are working on a diesel? WHUT? stay of VCDS please :P