Dear Friends, If you want this power point presentation of Soft foot, kindly comment your email address in this video comment box.
@MuhammadAli-ev2ym4 жыл бұрын
alichaudhry333@yahoo.com
@rasetech4 жыл бұрын
Kindly check your mail
@MuhammadAli-ev2ym4 жыл бұрын
Thank you Sir is there any formula for calculated the shim of soft foot motor...
@rasetech4 жыл бұрын
@@MuhammadAli-ev2ym I am not sure about the formula. But practically you can do it.
@jareddael54844 жыл бұрын
jaredlead33@gmail.com
@matthewmason14363 ай бұрын
Excellent presentation - well done.
@antonyyohannan647710 ай бұрын
Cutted shims are allowed underneath the base frame? It's in an API 686?
@rasetech10 ай бұрын
As per API 686 on Installation Angular Softfoot are not acceptable. Parallel softfoot only accepted.
@muthukumarn97584 жыл бұрын
Great information.
@rasetech4 жыл бұрын
Thank you ❤
@muthukumarn97584 жыл бұрын
@@rasetech sir pipe line flow calculat .blower three loop service . uploaded sir please
@muthukumarn97584 жыл бұрын
Your channel used lucky for me sir
@rasetech4 жыл бұрын
@@muthukumarn9758 sure sir
@ebukareuben57854 жыл бұрын
Thanks a lot Sir,i have learnt a lot from your videos.Kudos to you,keep it up.
@rasetech4 жыл бұрын
Thanks alot for your kind words.
@jagadishkumar7062 Жыл бұрын
Thanks for making this video
@alpha22854 жыл бұрын
Wow! Such a wonderful video to learn about soft foot ... really very useful and perfect one...thanks bro...keep it up...
@rasetech4 жыл бұрын
Thanks alot for your valuable feedback. Good Luck.❤
@ranjankumarsinha74104 жыл бұрын
Thanks for uploading knowledgeable video Pls keep it up We have learned more from your videos
@rasetech4 жыл бұрын
Thanks alot for your comment and support. All the best for your future.
@shariquemallik59314 жыл бұрын
Thank u so much for uploading videos in english...Please further also upload videos in english
@rasetech4 жыл бұрын
Thanks for your valuable comment.
@deepsavaliya9524 жыл бұрын
Sir, Great explanation..👍
@rasetech4 жыл бұрын
Thank you for your valuable comment.
@vikenkhalasi24454 жыл бұрын
You are doing a great job.
@rasetech4 жыл бұрын
Thanks for your comment.
@sanj99124 жыл бұрын
Nice useful presentation...Pls share more presentation on different topics in rotating & static equipments maintenance...sir..You have nice presentation skill.
@rasetech4 жыл бұрын
Thanks for your valuable comment. And Many thanks for your support...❤
@danukaashan27353 жыл бұрын
Sir our ship going to change engine and gearbox.please can you tell me procedure for that
@rajeshrajerajesh26914 жыл бұрын
Super bro... slip gauge alignment panratha pathium oru video podunga bro
@rasetech4 жыл бұрын
Slip gauge same procedure than bro. Feeler gauge use pandradhuku bathil. Neenga slip gauge use panna poringa avlo than bro difference.
Nice presentation for learning .please explain where we put the base of the magnetic stand during dial gauge measurement.
@kondayyanaiduaaa3 жыл бұрын
Sir please tell me I got the shaft foot reading 0.50mm how much shim can I add?
@nirmalsurendranmenon70492 жыл бұрын
when we add shims for soft foot, will that disturb the vertical and horizontal alignment that was already completed?
@rasetech2 жыл бұрын
Yes correct. Soft foot needs to be corrected before alignment.
@nirmalsurendranmenon70492 жыл бұрын
@@rasetech Ok let's say we corrected soft foot before alignment and then we start to do alignment where we determine by calculation that we have to add shims, so that may result in bringing the softfoot back again. So how do we resolve such situations?
@rasetech2 жыл бұрын
@@nirmalsurendranmenon7049 Once you corrected your softfoot and shimed properly. then you will correct the misalignment by adding shims or removing shims equally from Front foot 2 legs and back foot 2 legs. So softfoot shims remains same at the moment. So It will not disturb again. First practically try it for the same. Then only its easy to understand. implement the same as practical. and Provide lockdown bolts with exact torque value for the bolt tighness.
@nirmalsurendranmenon70492 жыл бұрын
@@rasetech ok ji thanks. Will do
@amitchoudhary36863 жыл бұрын
Your videoes are very informative...your hindi is also good ...keep uploading more videos....
@rasetech3 жыл бұрын
Thank you very much for your support
@aldorrymiftakaruna12643 жыл бұрын
hello sir, when we measuring soft foot, the motor and the pumps are coupled or not?
@kondayyanaiduaaa3 жыл бұрын
Thank you for share the information
@محمدالمصطفيحميده3 жыл бұрын
V good
@kondayyanaiduaaa3 жыл бұрын
Sir incase shaft foot reading I get .50 mm how much shim can I add please tell me sir
@rasetech3 жыл бұрын
See this video clearly you will get the answer... thank you....
@veerapandian43984 жыл бұрын
Thank u nice work
@rasetech4 жыл бұрын
Thank you bro❤
@mukeshkumar-ni6wx4 жыл бұрын
thank u sir,please uplode face to face alinement method video ,please
@rasetech4 жыл бұрын
Sure sir i will do it. Please stay tuned.
@Studyenglishwithfun0074 жыл бұрын
Good video
@rasetech4 жыл бұрын
Thanks for your valuable comment.
@muthukumarn97584 жыл бұрын
Sir next pipe flow . blower clearance check video sir
@rasetech4 жыл бұрын
Sure i will try... thanks for your comment.❤
@Apriest993 жыл бұрын
Sir is there angular shim available for correcting angular soft foot if not then how can it be done🙏pls answer sir
@rasetech3 жыл бұрын
Readymade shims are available Or you can cut from shim sheets...
@Apriest993 жыл бұрын
@@rasetech thankyou sir🙏
@DilipKumar-sp2fg2 жыл бұрын
But as per api 686, step shim or cut shim can not be used for soft foot correction.
@rasetech2 жыл бұрын
Thanks for the information. Yes You are right Cut shims are not allowed from construction and commissioning time but unfortunately some of angular soft foots will occurs on the operation and maintenance time period. So from maintenance you cant rewok on the base with short period. in this case we should use cut shims to cover angular soft foot cum parallel softfoot. Theoretically you can say but practically it will not work out. Thanks for the comment. I will appreciate for the same.❤
@DilipKumar-sp2fg2 жыл бұрын
@@rasetech agreed, to reduce the angular soof foot in future, for that during construction phase motor base blue matching as well as foot checked without shim . for that used dial indicator over motor base or coupling and check soft foot for all 4 foot and reading must be within 0.05mm. In this way we reduce possibility the angular soft foot for future case
@rasetech2 жыл бұрын
Great. Thank you very much...❤
@prabuyuvi8394 жыл бұрын
Bro ethuvum company onroll job iruntha sollunga.
@rasetech4 жыл бұрын
Onroll job na enna bro.
@prabuyuvi8394 жыл бұрын
@@rasetech bro Intha G. E. T(Graduate Engineering trainee )antha maari staff ah edupanga la