Round Pipe Bending Mistake // Round Pipe Bending Tricks

Round Pipe Bending Mistake // Round Pipe Bending Tricks
How to prevent thin stainless steel pipe from being compressed
metal and steel pipe wrinkle problem solve
#mdkhan
#diy
#welding

[@kirbyn2010]

Good show, guys. Simple and straightforward instruction with proof.

[@billarroo1]

Great idea ! I worked in a metal forming shop, we used a special metal called "KIRK SITE", it is like Aluminum, except it melts at 165. degrees Fahrenheit, we would heat it then pour it into tube or pipe then make the bends. Mostly in STAINLESS STEEL, then heat the piece and the KIRK-SITE would run out and the piece would be smooth without defects. Great Video. Greetings from Los Angeles. California 🇺🇸

[@АлександрГришутин-и8ю]

Я заливал воду замораживал ,гнул ,потом лёд растает и вода выльется из любой конфигурации.

[@ajwright5512]

Thank you for this: This was amazing to me, so I did some research - : Kirksite melts at 395°C (745°F), it looks incredibly useful - The stuff you were using appears as though it could have been Cerro Bend which melts at just 70°C (158°F) ?

[@MrKrn558]

Have you ever tried sand? It's easy and efficient

[@antoninhanzlik8092]

@@MrKrn558 Nebo se dá použít vhodná pružina.

[@bltoth1955]

Haha, you might want to check your 165* melting point.

[@PILOTabcdce]

первая труба была с тонкой стенкой ) а у второй стенка толще) и согнуть ее без вмятин проще ) засыпь песок в первую трубу и посмотрим на результат)))))))))))

[@KAB2525]

вы дурачок? Раньше так отводы и гнули, в домашних условиях что называется. Начиная с полдюймовой трубы, а там стенка 2.8 мм, без песка заламывалась!

[@ANISH7712]

સરસ સરળ અને ઉપયોગી આજ રીતે પ્લાસ્કિટ પાઇપ માં માટી નાખી બહાર થી હોટ ઘન વડે સરળ તાથી બેન્ડ કરી શકાય છે આભાર

[@cesarminas8283]

Nice thank you very much👍👍👍

[@1Mind-Over]

Wwwwwoooowww !!! So amazing 😍 I haven't seen anything like it. You guys ROCK!

[@michaelgertos812]

Thank You very much MD KHAN!! May God give you more blessing!! ❤️❤️

[@dubes5594]

First tube was thin wall aluminum. Second tube was thicker wall stainless. (You can tell by the color of the weld) I call BS using sand without capping the ends TIGHT.

[@briztol7748]

No this is working...i used it before

[@rsz90182]

You taking something that works and dismissing it. The point of the video is to use sand to avoid the example given.

[@breezybmetal8646]

I agree looked like 2 different pipes and first one looked like thin wall - but I do know sand does work

[@cheesynibblets4960]

Would be better with the clamp on the side that is moving. You pull the material into the bend rather than stretch it.

[@robertomerced1184]

Good job; congratulations.

[@alejandrosolizlopez2689]

Gracias por el video al fin voy a doblar tubos correctamente....... Esa dobladora me gusta..... Si no es mucho pedirles detalles o planos.... Gracias😢

[@Akil304]

Fst like🤗🥰

[@unclemarksdiyauto]

I will remember this cool trick for sure! Thanks!

[@alexandregenesis7]

Bravo! Great!

[@AaAa-nm1jj]

Прекрасно !!!👍

[@willianfajardo3455]

Muy buen consejo utilizar arena para que no se desfigure el tubo... desde Colombia

[@kontruksi317]

Cara bending pipa yang bagus 👍

[@frankttt604]

Very good - thanks

[@Y_K153]

Super Arbeit 😂😂😂

[@danielgnanathikkam6608]

The pipe which came out with fine bended is thicker than the previous one which was very thin but the guy did not show the thickness of the pipe but for first pipe he showed that it was thin

[@buduchild]

you didnt get the point of this video? He showed you how to properly bend a thin pipe. And thats how you supposed to do it.

[@WinterSoldier100]

​@@buduchildno, you

[@jorgemoraga2427]

Cambie la curvadora, trabaje con una bien diseñada y nunca deformo un tubo sin añadir arena .en produccion en masa no puedes estar perdiendo tiempo en taponar con trapos apretar la arena etc. Osea mala la maquina ademas esta mui lejos el punto de apollo, y pierdes tiempo en amordasar el tubo .lo digo con 5 años de experiencia trabajando con curvadoras curvadoras

[@SHABRASH]

Which companies pipe bender you are using?

[@kingronald5376]

WOOO es una super máquina 🖒 podrías hacer un tutorial de como construirlo porfavor. Saludos de LIMA/ Perú 🇵🇪

[@steelmastercfa5130]

kzbin.info/www/bejne/nKrHqneliZusj5o

[@117TheKill]

¡Excelente trabajo MD KHAN! Saludos

[@jerle1703]

You need to fill sand to be successful, that is because your technology is not good, so how much time will be wasted. You don’t need to fill sand, just change the shape of the mold groove and you can bend successfully.

[@paraisojoan1910]

Nice very 👍🏻

[@Akil304]

Pin kro bhai 😊😊

[@Akil304]

Mashallah 💞💞

[@rajenchamoo5990]

Good ideas

[@Explorador65]

Muchas gracias Maestro! 🙏

[@sunilsteelworks]

Bhai aap apna video kon sa category me upload करते हैं

[@КонстантинХардин-б7ю]

Так тяжелее,но результат стоит того

[@MDsaddamShaikh-i9e]

Assalamualaikum Bhai ye kam Aap India me kaha se ho aur kaha kar rah ho

[@pipebendingpunchingGracia]

👍👍👍👍

[@marinongbicolano1319]

Good job keep safe stay connected

[@steelmastercfa5130]

kzbin.info/www/bejne/nKrHqneliZusj5o

[@lawrenceveinotte]

Sand takes time, could easily convert this to a mandrel bender and be able to make bends with half the radius.

[@omararab6995]

Can we replace the sand that you put in the tube with mandrel

[@robertthomas5906]

No because the mandrel won't bend.

[@MrNams]

Great video, thanks for sharing #mrnams

[@surewinner]

How do you keep your white cloth so clean?

[@ntal5859]

First you must wear the shirt for two to 12 months straight, this will allow your bodies natural body odour to linger and survive long after you remove it for washing[your body not the shirt] remember you didn't wear it months straight to wash out those built up grease stains, next find a third world country so dirty no one notices your stench or filth, once you have gained access and blended in with natives you begin to whiten you clothes[note the joke of using plural of cloth as we all know that one shirt is it] now the whitening begins, role in lots of dusty environments usually asbestos is good as impregnates your rags you will become more or less fire proof, then the final stage is to literally burn all that grease and fat out of the clothes as you enjoy the once a year bath in the nearest river/sewer and bingo fire proof clean rags which no one dares steals as the stench is your own unique flavour. Enjoy.

[@jimparsons6803]

Slick. I've watched something like this done with pvc pipe.

[@_Jeha]

Красота, вершина слесарного мастерства!

[@cagirahmathidayat2347]

great idea

[@ramazankutlular5461]

İlk boru alüminyum ikinci boru paslanmaz birde aparatınız eski çağlardan kalma .benim kendi imkânımla yaptığım aparat pürüzsüz ce büküyorum paslanmaz ve normal çelik.

[@mtrq5679]

Kitne gaje Ka pipe hai

[@ichkannviel]

Our dyed-in-the-wool " skilled workers " God forbid they come to Europe too.

[@ache7777]

👍👍👍💪💪💪🙏

[@longdong3889]

Add grease to the follower and it should improve a little

[@alphasiera1757]

Will any sand do?

[@ninoalban8973]

Tnx sa info sir

[@toddwolfe5659]

My dad used to put springs inside to pipe

[@koya8787Sdeq]

❤❤❤❤❤

[@andrewgeorge5805]

It would be better if you use a pipe bending spring inside it so you can pull it out after you have done it on the bending machine you have olé.

[@noshadkhan1478]

Super

[@Akil304]

Kha se ho aap bhai

[@MDKHAN-9907]

Jabalpur MP

[@Akil304]

@@MDKHAN-9907 ओके भाई

[@jeanjean4563]

Bon travail!

[@DT-abcd]

Getting the rags and sand out is even more difficult. A better way is to heat the metal red hot then bend it. Much better method

[@marcoscolina4568]

😊😊😊😊

[@azharshah6384]

Bhia circle ka size kitna hai

[@Тема33]

Какая толщина стенки трубы?

[@mehdiarab6189]

Hi, Why you do not use Mandrel for tube bending? it's very simple.

[@iguanapete3809]

They can't even afford shoes is probably why.

[@mehdiarab6189]

@@iguanapete3809 mandrel is very simple and chip, we need a round rod inside tube

[@alphasigmasezon8597]

❤

[@frankfernandes1282]

Best bending

[@garygerard4290]

'smooth bend I'd grease up all the moving parts.

[@sigisalmen2399]

OMG Are you serious? I can't believe what I've seen! Black shoes and white socks? 😱

[@raylander1189]

Não vem que não tem, o primeiro cano era muito mais fino que o segundo, quero ver ele fazer curva no primeiro mesmo com areia

[@ورشةاولادابووحيد]

Actually the tubes were already replaced by one with a larger thickness.

[@diegledw]

Si tienes. Que hacer 100 tubos te lleva meses con ese sistema buena esa felicidades

[@Usman1tv]

Bahi ap Pakistan main dilevrey Kar sktay hain

[@nadirkhanjadoonofficial4802]

Kia chahye apko?

[@nadirkhanjadoonofficial4802]

Ye machine chahye?

[@STREETWELDING]

Goodd

[@radwanboualam1478]

Pour plier le tube de cette façon, il vous faut une olive,pour que le tube ne se casse pas, essayez avec une olive

[@abdrahmanabdullah3113]

Awesome

[@leiladaquil6587]

Great

[@Тема33]

Если немного доработать приспособление то можно без песка обойтись.

[@artyworlds]

Price please

[@tavlogs1398]

Pahele vala pipe bahot halka tha 😄😄😄

[@MrNams]

😀😀😀 #mrnams

[@alltogetherplaytubefingerf6045]

good to know

[@anilshekhawat4819]

सिल्वर पाइप की मोच कसे निकले

[@MoazzamkhanMkhan-kn5he]

Machine ka naam kya hai

[@friedchicken1]

YES!

[@Болгарин-т5р]

По мне так на 2.33 минуте лучше трубка загнулась, чем с песком!

[@hanssmiletzki9127]

Wie im tiefsten Mittelalter.

[@nevendingdream6905]

Genius

[@verdemugurel4mai]

Or you can try filling it with sand

[@MDKHAN-9907]

Yas

[@derkompressorschrauber]

Why did you use the wrong diameter of bending device? No wonder the pipe is folding like this…

[@6061-y5q]

Nice

[@Dubukku]

What a waste of time. With proper tool you can bend even 0.45mm thick tubes without shrink. We are doing it in hundreds daily

[@petermcgrath5215]

Geniuses

[@gamalatef]

يوجد افضل من هذا

[@yongxie857]

这个我以前弯酒管永的设备

[@davidbrewer7937]

If in doubt pack the pipe with sand first...

[@yurim2000]

Офигенный инструмент - все из кривой, приваренной на соплях арматуры, на второй ролик денег не хватило.

[@vxfhjnbgd]

Не правильно собрана. Можно без песка

[@newideaz4973]

We need wheel of dye

[@НиколайПушкарев-ф5щ]

👍× 100000000

[@carlosenriquefalconirosale7105]

👍

[@kakangprabuteknik1459]

Segala pake pasir ..bikin rumit aja ..ngak praktis...alat kurang mantap..

[@marcoscolina4568]

Hola

[@MDKHAN-9907]

Hola

[@wannamonslo9626]

You gotta fill it up with sand.

[@FabricationWeldingmetal]

Ye 75 gaje ka pipe hai 😂😂

[@sikunyutsikunyutsikunyutsikuny]

Ia kalau tidak di isi pasir pasti hancur

[@sartajmumtaj1563]

Are Naas he kar daya katye

[@lamPhamduclam]

🏴‍☠️🏴‍☠️🏴‍☠️

[@Khalidbehzadradiators]

15+15=25

[@ЖекшенДалиев-ы8и]

второй по толще по моему