Ep03: Plasma CNC build | New Z axis and MOVEMENT!

  Рет қаралды 1,548

routercnc

routercnc

Күн бұрын

Пікірлер: 11
@homemadetools
@homemadetools 3 ай бұрын
Nice build series. We shared this video (and the first two parts) on our homemade tool forum last week 😎
@routercnc9517
@routercnc9517 3 ай бұрын
Ok great. Should be more to come over the following weeks (and months!)
@routercnc9517
@routercnc9517 4 ай бұрын
There was another comment in my inbox about how well the 3D printed parts might hold up against the plasma. But it was deleted or did not appear here, so my answer is I've seen other CNC plasma machines use 3D printed parts around the torch area and been OK. So let's see how it goes. I do think the 3D printed cover near the torch might not last that long as it is so thin. When this thing is finally working I'll post something, but we are some way off!
@panbekon1470
@panbekon1470 4 ай бұрын
I saw on that board's terminal block there is on/off that you did not connect. I guess that goes to enable pin on driver.
@routercnc9517
@routercnc9517 4 ай бұрын
Yes I think you are right. I don’t use the enable contact on my machines so didn’t connect it. I’ll test it and see, thanks.
@johnyoung6479
@johnyoung6479 4 ай бұрын
Does the on/off switch activate the enable pulse? Very enjoyable keep the good work up.
@routercnc9517
@routercnc9517 4 ай бұрын
Oh, yes that could be it! Maybe I'll wire up the enable and see. I'll report back if that works or put it in the next video.
@jacksat2252
@jacksat2252 4 ай бұрын
Buy some different sizes of piano wire, you have a lathe so you can make springs to the exact specs you want. 😉👍
@routercnc9517
@routercnc9517 4 ай бұрын
Funnily enough I've been thinking of doing just that for a while now. There are quite a few videos out there showing how it can be done. Maybe I'll give it a go and make some tooling . . .
@4arus
@4arus 3 ай бұрын
Зачем так сложно. Можно было добавить две каретки на нижнею часть и закрепить на них
@routercnc9517
@routercnc9517 3 ай бұрын
That would have too much friction and cause problems touching off on thin metal sheets. The linear bearings should slide easier.
Ep04: Plasma CNC build | X gantry finished!
46:46
routercnc
Рет қаралды 2,9 М.
How To Build a BIG CNC Plasma Cutter for under 750$!
25:26
HOMEMADE MADNESS
Рет қаралды 85 М.
Andro, ELMAN, TONI, MONA - Зари (Official Music Video)
2:50
RAAVA MUSIC
Рет қаралды 2 МЛН
Thank you mommy 😊💝 #shorts
0:24
5-Minute Crafts HOUSE
Рет қаралды 33 МЛН
Vampire SUCKS Human Energy 🧛🏻‍♂️🪫 (ft. @StevenHe )
0:34
Alan Chikin Chow
Рет қаралды 138 МЛН
Making A Complex Hollow Carbon Fibre Drone Fuselage
23:56
Easy Composites Ltd
Рет қаралды 271 М.
Ep01: Plasma CNC intro | Bestarc BTC500XP 11th Generation
57:44
routercnc
Рет қаралды 3,4 М.
Stealing Energy From Radio towers Using Plasma (ft. Geerling Engineering)
20:02
Ep05: Plasma CNC build | XYZ axis finished!
25:09
routercnc
Рет қаралды 1,8 М.
I Built The First LAMINAR FLOW ROCKET ENGINE
15:51
Integza
Рет қаралды 3,8 МЛН
Speedrunning 30yrs of lithography technology
46:07
Breaking Taps
Рет қаралды 1 МЛН
Shutting the Doors on our 15 Year Business || My Origin Story
35:43
Bourbon Moth Woodworking
Рет қаралды 367 М.
Ep07: Plasma CNC build | Downdraft sheeting and slats!
28:39
routercnc
Рет қаралды 1 М.
Ep06: Plasma CNC build | Main assembly finished!
30:18
routercnc
Рет қаралды 1 М.
Andro, ELMAN, TONI, MONA - Зари (Official Music Video)
2:50
RAAVA MUSIC
Рет қаралды 2 МЛН