Rsx AWD trailing arms

[@wiaterek6462]

I can confirm that elongating the holes works. I had to mill the holes up to around 2cm(0.78inch). Alignment is spot on :) Thanks for sharing this info MrBoost, it was very helpful!

[@MMAutoPerformance]

This helped me out so much finding new info as I’m building my own I have a full crv swap already have my subframe on 💯 just waiting on a build lower end

[@Blendsurgeon]

Thanks for the info brother , hopefully you make a full in depth video from start to finish of the conversion in the future

[@yosh_tuned]

This helped out tremendously and saved me some bucks. I'll be going this route as I all I need are the 1310 joints and some small miscellaneous parts

[@blckevo8]

You can also use a stock element driveshaft

[@yosh_tuned]

@@blckevo8 yeah, I have already bought the freelander ds with it's vc. The rear is what I'm missing and this helped out alot

[@blckevo8]

Glad it helped man!

[@KrazyLu61]

Hey brother, thank you for sharing this video and your knowledge and experience. I found your other video about your thoughts on the S1 built spindles. I was about to pull the trigger on those things myself but not no more. Thank you.

[@BEubankbuilt]

Hell yeah good info! Thanks brother

[@jsd4979]

great job!

[@OxNefu]

great video i plan to awd my rsx

[@mickl8212]

Wow, nice advice there. It's not good loosing out on the original manufacturer geometry especially if it upsets the car.

[@babyelephant3077]

The ep3 arms sit in the right place with the CRV hubs You just need to watch out because it widens your end.

[@rsxboys5393]

Hey it very good information but I use the Honda Element arms n I don’t have any of those problems the only thing I see the Honda Element arm sits lower so I had to get shock space

[@incconcreto8816]

Very nice !!

[@Jagensfurie]

And me having done the AWD swap with front lower crv control arm with crv suspension front and rear. Got much trouble with the front and still have way to much camber in the front, i look like a drift car lol. I got the same problem with the rear end as you have, i tryed first all crv stuff and it was even worst than your, the crv suspension in the rear was binding like crazy, it was scary. I then used rsx control arm, then crv sprindle assembly. For the sway bar i used the CRV sway bar with crv link-kit that i put in reverse so it bolt on it, but it touch sometime the axle. I got problem with the axle too, i had to use 2 left crv axle since the right one is way too long. The car run, i got to the alignement shop and cannot be aligned, yea i got 1 degree offset from the toe arm, so today i my own way to solve this problem and what i did is i took out the toe arm and flip it upsidedown, you get like 1/2 to 1 inch more however you cannot bolt the 3 bolts since only 2 bolt align. I now seem to be toe-in so i will be able to align next time. For the last bolt, i will solder a flatbar to the tip of the toe arm and drill a hole and bolt the last bolt. For the front i might have to change the suspension top plate for an ajustable one but that's for another time. I got the same idea as you for machining the hole but then i told myself to find another way.

[@Jagensfurie]

What's funny with my build is that i have like 11 inch clearance so i can move under the car without hydrolics jack. But i think about adding 2inch spacer in the rear because with the crv suspension the wheel are inside the fender... and look gross

[@aplong1911]

Great info! What are you doing with the welder down there?

[@javentesla7164]

Wth is going on? I remember way back when I first bought my 06 RSX I wanted to do an AWD conversion. Everyone thought I was crazy and said it couldn't be done for a reasonable cost/time. Now it's 2022 and it seems like everyone is AWD their RSX lol. I watch the K20 engines/k24 frankenstein's with SC or turbo get 600HP+ easy but if the platform is FWD it's kind of pointless.....now with AWD I say gimme gimme gimme! Lol. Thanks for the tips. Goodluck on your car!

[@KevZilla-0]

So at the end was this the best option? I have crv trailing arms but would prefer rsx ones due to that inch space

[@erm386]

Still debating if I should awd my 06 rsx type s

[@frias2287]

Nice💪💪💪💯

[@44_TOUGE]

Have you had any problems since doing this if not I’m finna do it to my rsx

[@rhok9007]

Well done mate

[@user-nu4dt8mv5w]

What fuel system did you use? Also what about driveshaft?

[@briangaglio9450]

I think I heard you say that the same could go for an EP3? I'm doing a complete swap for a K24 and want to go AWD as well. This method will work just as easily or should I just buy the hubs? I want to do the 5 lug conversation off the Type s.

[@prcc8793]

You the man 💪👍I have a 05 type s .and I will like to do that set up.plus I'm going turbo too and get a new paint job(white) don't like Milano red .can you tell me exactly what i need.thank you

[@blckevo8]

Easiest way would be just watch all these videos and the other ones around KZbin

[@tetfemal03]

I'm assuming that this is the same process for an em2 civic? And which front subframe are you running?

[@360kustomssiskjr6]

Nice

[@mazdafy1428]

What year crv are the rear trailing arms from?

[@kuamvwj3801]

Good info subbed

[@GZZZILA]

How much for your setup?

[@Dc5.]

What are your wheel and tire specs? I love the stance

[@blckevo8]

17x9 +35

[@rayvnicolas24]

At 5:40 you said front bolt and pointed somewhere to the rear. Which bolt are your referring to and what do you mean shim it?

[@timludwig1297]

I could be wrong, but I believe he means using the technique of using shims, but with washers instead. It's where 1 of the CRV parts meets an RSX one.

[@USDG-Anhell]

@mrboost how did you get the crv spindles on the OEM rsx read arms? When I’m trying it seems like I have to stretch out the part where it going In

[@blckevo8]

If I understand correctly seems like you may need to make those hole bigger like I did.. verify you have the right year spindle

[@USDG-Anhell]

@@blckevo8 what I needed was to know that I needed to grind down the bushings on the crv spindle to get them to go in the Rsx arms. I did it though brother thank you now I’m going to visit my local drive shaft shop to see if I’m going crv single shaft or Land Rover shafts with viscus coupler. I have all parts I just don’t know what route I wana take

[@two40zsx]

Does cutting the brake bracket effect the structure and strength of it???

[@blckevo8]

Not in a meaningful way

[@itsjussjerry]

That’s strange. Idk about the CRV arms, but with my element arms, my alignment is just like factory.

[@blckevo8]

I might of said it wrong yes it will align but you still have angled movement in the lca and shorter wheel base

[@user-vu3uy7np9y]

🏎👌👍

[@nimbuzdc5647]

What year crv spindles ? I’m new to the whole Awd thing

[@blckevo8]

04

[@Darkpaper11235]

@blckevo8 Hello brother thanks for your vids! I watched them so many times to learn the way you did this. I got myself a 02 Rax type s. I found the hole element Awd conversion, and was wondering if element and Crv are interchangeable? Since the guy who's selling this told me i need to cut the axels? If it is to much to ask shooting you some questions by email or any other way? This is my dream build and im doing everything by myself! Thanks Isaac Here!

[@blckevo8]

Yes they are

[@Darkpaper11235]

@blckevo8 Great, i appreciate it man! Im not from here so... Does 1400$ for the hole AWD swap worth it? I might do N Box gass tank or true focus fabrication gas tanks. I'll do some videos of the progress at some point! Hopefully in less than a year. Thank you for your videos man, they inspire me! Sonora, Mexican living the dream in Oregon! lml Peace brother

[@ninjafishing7120]

Hye . Thanks for the video . Just wondering about sway bar front and rear . Is there any chance to use it after awd convertion . Thank you

[@rileyolson1517]

front will use stock crv working on getting my rsx rear to work

[@ninjafishing7120]

@@rileyolson1517 cant wait for it .. 👍🏻

[@cajnauto]

How do you like the car being awd?and?. Looking at one In Texas. Seeing if they would trade for my tsx 6mt

[@blckevo8]

It’s great

[@cajnauto]

@@blckevo8 cool to see some nice cars out in Louisiana

[@WiseguyHonda]

My crv hubs have a larger spacing between the lower bushings. Did you have this issue? Its 1/4 inch or so

[@blckevo8]

That’s what this video covers

[@WiseguyHonda]

@@blckevo8 i didnt see how you worked around that. Ill re watch lol

[@teampoko5118]

Trailing arm rsx ,spindle crv and crv hub? & for the handbrake cable any modification? Sorry my english is not good

[@blckevo8]

Yes and ebrake bracket needs a little adjustment but works

[@teampoko5118]

Thank you very much

[@melvinortega762]

What year crv you got the spindles from ?

[@blckevo8]

04

[@mannywatts4134]

Whats the bolt size and length you used after drilling??

[@blckevo8]

I used the stock crv bolt I’ll have to find measurements

[@mannywatts4134]

@@blckevo8 ok ill grab em from the dealer, i just ordered fresh rsx ones after seeing this video lol

[@JonnyShertz]

only thing about the AWD build I don't like is the fuel cell. if they did a better gas tank feature I'd be all over it

[@yosh_tuned]

You can use the honda N box and just create a false floor while still maintaining the stock fuel cage

[@JonnyShertz]

@@yosh_tuned does the interfere with the diff at all?

[@yosh_tuned]

@@JonnyShertz it doesn't. It's a perfect pathway with plenty of room. Tuning with nick did a step by step vid as well and what all he used.

[@JonnyShertz]

@@yosh_tuned might have to look into this

[@JonnyShertz]

@@yosh_tuned ya just watched it. Not a fan of cutting the back half of the car apart honestly.

[@tylert8594]

How can I contact you?

[@rynoatt]

Man, who does your neighbors flowerbeds?

[@blckevo8]

I was legit like wait what.. then saw it was u 😂

[@daunushamilton]

What did you use to do the holes ?

[@blckevo8]

Worked up to 1/2 inch then used a step bit to join the 2 holes

[@daunushamilton]

@@blckevo8 thanks man I have element arms and element spindles I’m deff gonna do this when I put my babygirl together

[@luisrivera3440]

Would this be the same for an EP3?

[@blckevo8]

Can’t promise but I’d say yes

[@luisrivera3440]

@@blckevo8 I'll give it a shot. Thanks

[@2GRFExv20]

@@luisrivera3440 did you figure it out

[@luisrivera3440]

@@2GRFExv20 I'm running crv trailing arms

[@jeffreycastro7781]

Is it the same for EM2?

[@tourqualitygolf]

Em2 is basically a Rsx. I’m doing this same thing on an es2 4 door sedan.

[@blckevo8]

Far as I know yes

[@winru2]

Poor mans skyline

[@adrianvega4817]

what about element arms ?

[@blckevo8]

Same story

[@adrianvega4817]

@@blckevo8i know its late but what year crv hubs you use ?

[@Cloneufc]

Why was this post removed from the AWD thread?

[@blckevo8]

No idea.. they be hatin

[@Cloneufc]

@@blckevo8 Dude! The guy that runs the Facebook forum RED, I thought he was cool, I even bought a diff mount from him. He is a hater. I posted some cool how-to's and he removed all of them and acted all superior like he already knew everything BS! You came up with some good info and I appreciate it.

[@A2ZREY]

Crv same as elements?

[@blckevo8]

Not exactly

[@A2ZREY]

@@blckevo8 I have element trailing arm are they still shorter then rsx ? And why did base rsx goto crv trailing arms if you lose a inch ?

[@A2ZREY]

@@blckevo8 and can I really use my stock element drive shaft and not have to cut it ?

[@blckevo8]

@@A2ZREY he explained why he changed I forget the reason.. the inch doesn’t really matter for what he’s doing tho.. and also we didn’t do it the exact same way

[@blckevo8]

@@A2ZREY yes

[@ProblemChild407]

U take too long to talk🤦🏻‍♂️

[@eljefe3993]

Wow… why not get a subi? Keep the fwd

[@jaysmith2385]

Mrboost what’s your name on gram? I need some help with my rsx awd conversation.