S&G 6730 (001)

[@couldabinmore]

I need to replace two locks. I was given two GSA classified document safes. One had 6 holes drilled and the entire lock was removed. The door opens and closes with a turn of the handle. The other, had the dial removed and one hole drilled. A safe guy showed me how/ where to drill, to drive the deadbolt out. I got through the 3/8” door plate but could not drill the inner box around the lock. I was able to blow through that with my plasma torch. All holes will filled with welding. The safe I had to drill and torch, had what was left of a Mosler PRK-302? I have photos. What I need to know is the mounting hole dimensions of a S&G 6730. I’m having trouble finding that info by internet search. There are 4 threaded holes on the inside of the box holding the lock that were used to mount the Mosler. I would be a big help to find a lock that uses the same hole spacing dimensions! If you have that info or can direct me I would appreciate it tremendously. I can share photos of both doors if you need.

[@grainorice8293]

The mounting holes for safe locks are standard. You should be able to use the same footprint. I do recommend using a certified safe tech to install locks you will depend on.

[@educatebo]

After the S&G which would be more educational, the Lagard 3300 or Big Red CDL3?

[@grainorice8293]

You're good either way. Pick up one and then then other latter on. Watch out for Lagard 3300 knock offs though.

[@educatebo]

@@grainorice8293 The 3300 from MBAUSA should be reputable. thanks

[@grainorice8293]

@@educatebo MBA is a great site and great people too.

[@elmerzuluaga8392]

Excelente video,excelente informacion

[@grainorice8293]

Thank you

[@sharit7970]

Hi there- question- have you worked with any locks that have a relocker that has a pin on the end that inserts into the side of the bolt instead sitting in a groove on the side of the bolt like in this video? Long story less long, I have a family member's old Remington Rand file cabinet/ safe with an S & G group 1 lock with an 'arrow knob' in the center of the dial. It was left unlocked [yay!] so I could cheat and take the back off the lock. I figured out the combination since I can see the wheels [genius that I am....] but I'm not sure what the trick is to the relocker. It wants to sit with the pin in the bolt- even when the back is on and putting pressure on the opposite end of the relocker. I'm not sure if it's missing a piece or what. Any insight would be greatly appreciated! Thanks.

[@grainorice8293]

I've only had experience with common relockers.

[@chriscapune7873]

Awesome!!! Wonderful decoding !!!! Just subscribed to your channel. Great video!!!! Stay safe!!! 👍🐈👍🐾👏😷

[@grainorice8293]

No pun intended :) Thanks.

[@肖川-e4o]

@@grainorice8293 how to crack lagard3332?

[@grainorice8293]

@@肖川-e4o Very similar. I think there is other channels that talk about that lock.

[@肖川-e4o]

@@grainorice8293 I can't find a way, and I can't find any.

[@TallanPick]

Great video again, thanks for showing ;o))

[@grainorice8293]

Any time. Thanks.

[@chriscapune7873]

Where did you get your mount for this setup, can’t seem to find one Thanks buddy.

[@grainorice8293]

I get them from MBA (mbausa.com/training-aids/lock-mounts-for-training/)

[@chriscapune7873]

Thanks!!!

[@kentlundberg]

Nice video i have a question is it possible to get a copy or photo of your graphing sheet ..i have just started learning to manupilate ..and your sheet was so informative

[@grainorice8293]

I don't think I have the sheet for that video any more. Sorry.

[@kentlundberg]

@@grainorice8293 Ok thank you for the answer i think i use your video to make a sheet .. another question i did get a sparrow vault is this Good to start with...i did see your video about change to 7641

[@grainorice8293]

@@kentlundberg I like the idea of the vault. You will be able to lern manipulation with it. I would recommend a moounted cutaway lock from MBA as your next. You will feel a big differance.

[@kentlundberg]

@@grainorice8293 thank you for the answer have a nice day

[@gvnumber3200]

So.... with your edits....how long was the actual time to open?

[@grainorice8293]

This one takes me a little under two hours. I'm not as fast as others and I don't practice consistently. I know of some that can manipulate these locks in 10 min.

[@Pyrolock]

Not good with last number (wheel 3) set in the forbidden zone -- fortunately no lock in or lock out

[@grainorice8293]

My wife is the combo setter and she is learning along with me. We were lucky.