SAE Atlanta O2R Tutorial

[@miniminiize]

This Tutorial rocks! It's by far the best Tutorial out there! Greets from Germany. SAE Munich. PS: We have Andreas Friesecke!! ;)

[@shayneoneill1506]

You probably should mark this as O2R96 rather than 02R, as they are very different beasts.

[@Abhishek-kg3je]

Great video ! Really helped me a while learning the console

[@phil_dp]

Excellent console

[@VoytekPavlik]

Thanks. You helped me understand that I had to recall the stored setting to get that work. Someone must have changed those, but good thing is the sound engineer got those settings stored when he set up the studio. Regards

[@mrjazzycharon2]

"the bottom line is, we need a dog for protection..."

[@ciaracorr6015]

it would be helpful if each time slot was put on the you tube video for instance : headphone mix 10:02 this way if we are just looking for one thing we dont have to go through everything very time consuming, thanks for the video.

[@zlarecords]

Also have a Yamaha 02r I don t get a signal at the stereo mix The signal led at the gain lights up, so there s a signal but it doesn t come to the stereo mix although i did the routing... Question: what to do? Kind regards Zla...

[@mathiasanotherarabguyibrah7632]

Greets from SAE Amman,Jordan!

[@nicolabrn4666]

Can i connect this mixer to get audio thru USB port? i wanna make a "virtual soundcheck"... Has it got an internal audio interface? I want to connect it to my DAW and mix with his internal eqs, effects in some "out of the box" way...

[@osayandeiboi382]

getting the mix thru the analogue main out record to a laptop is still analogue at the end

[@24entertainment77]

Could you show how to set up yamaha 02r96vcm as audio interface? With win and os

[@j.dragon651]

I have a problem I cannot solve that brings me here. I have an Alesis HD24 hooked up to the o2r with light pipes. I have three adat cards mounted in the mixer in slots 1,3, and 4. I cannot monitor the 17 through 24 channels of the HD24 with the 02r, through the stereo inputs 17/18 through 23/24 ? I can see the signals on the HD24. I have a meter bridge that is a bit confusing. I have used the manuals for both. I have tried different routings. I get 1 through 16 no problem. If anyone can help me, HELP!! Thank You J.D.

[@j.dragon651]

New problem, I bought my 02R96 for 250.00, everything seemed to be working correctly but the battery checked dead. After I replaced it board won't boot. I have tried initializing it, it will say it is going to calibrate the faders but never does anything, just sits there. I have tried initializing it more than once, some times it just sits there, you can see it loading on the display but it just sits there and sometimes it goes to the fader calibration warning but then it just sits there I asked someone who knows more than I and they responded with the following Does anyone know about the following???? It looks like a case of bios failure due to battery failure, I have seen this with computers, and yahama may need to send you an updated firmware update to restore it. I would contact them and inquire about this as they are the only source for this type of help. A lot of digital studio equipment today is just dedicated PCs with all of the added Ins and outs and surfaces for control added, these are subject to the same failures as Computers and must be regularly updated and keep alive battery's keep them usable If they are left unpowered for any length of time there is a risk of them not booting up when they are finally re activated. Thanks in advance Dragonworks

[@rastaboisrouge]

hello, first of all, thanks for this video. I have a problem with my table when I want to make the sounds come out through the effects patch. I plug my microphone into input 1, I raise its aux channel then I switch the master layer back to fader mode to give the level needed for 49/50 effects return but nothing happens. What could be done to get there please.

[@4FIVEHD]

SAE CHICAGO TUES HERE I COME

[@muziq99]

I'm happy for you. I Attend the SAE Institute of New York, "I love it"!!

[@AhitagniDasgupta]

A big help!!! Thanks :-)

[@freshproduce2170]

how loud is the console itself?

[@piratedprivacy9052]

perhaps the fan needs some cleaning? 😅

[@Greg_Stache]

thank you

[@PaWDrum]

Hi, i bought one 02r96 v2 and i'm trying to connect with pro tools using usb, but i don't get it. you can guide me? Thanks!

[@muziq99]

+Pau Llopis hey, did you figure it out yet?

[@kame5271]

+reem dollaz www.gearslutz.com/board/music-computers/851133-connecting-yamaha-02r96-hui-pthd8-via-usb-midi.html Scroll around the thread maybe ul find something.

[@muziq99]

Thank I appreciate it. I was only able to use logic Pro X.

[@kame5271]

Good luck mate! Reply if you figure it out

[@_JohnnySav]

+reem dollaz How well does it integrate with Logic Pro X? I can't seem to find any videos on Logic with this mixer...

[@EndOfEntertainment]

cool stuff :)

[@stephennyambori7040]

I have o2R and I can't get all my Sean even some Chanel's are not working

[@StudioKorgOfficial]

Ok

[@RoccLefty]

I am a proud SAE Atlanta ATP0613FT alumni www.RoccLefty.com