Unbelievable! This worked exactly as you said. I popped the resistor in, turned on, it burnt, I took it out, turned printer back on, and walla... printed perfectly. Thank you ssoooooooooo much
@MyPlayHouse10 ай бұрын
Thank You!! Hope I earned a subscriber :-)
@earlfrederick83 Жыл бұрын
Morton, Success! I don't understand why, but changing out all 4 of the toner cartridges with new, and at the same time fixed the yellow print problem! You're a Wizard! when the printer was warming up i noticed a mode that i hadn't ever noticed: "calibrating color density". Now the printer is like new with all the replacement parts and toner! Thanks for your cool counsel. Earl
@MyPlayHouse Жыл бұрын
Hi @earlfrederick83 Thank You very much! You are too kind.. glad you liked the video :-) Thank you for watching! :-)
@ntf86Ай бұрын
Thanks for this great solution! In fact I, for the moment, skipped the emptying part and directly went to using the resistor and just could print a page🙏🎉 awesome!
@MyPlayHouseАй бұрын
Glad it helped :-)
@christoga Жыл бұрын
Must admit it just worked. Drilling the 2 holes gently, using small plastic bags to empty the powder, cover it up with plastic tape. Then find 56ohm resistor (0.5W), put it on, close the lid, power on, got error C3-6520 on screen, open the lid, remove resistor. And Voilà ! I think my resistor didn't burn but it did reset counters. Thx man !
@MyPlayHouse Жыл бұрын
Awesome,, Happy to help!!
@jfkastner2 жыл бұрын
Instead of drilling holes into the plastic cartridge use an old soldering iron and MELT holes into it - since there will be NO plastic particles floating inside and damaging the image drum! I used to do that with VHS tapes to convert to S-VHS ;-)
@EmmanuelRAYMOND692 жыл бұрын
and you can refill old cartriges of toner with new one... making an hole.. make a paper funnel... and (outside without wind) refill with new toner powder ^^
@MyPlayHouse2 жыл бұрын
Okay,, I have heard about the soldering iron trick on the color cartridges if you want to refill them.
@Mobay182 жыл бұрын
As long as the print looks fine, you can continue to do this. But in general imaging drums need to be replaced eventually because the coating on the imaging drum can lose photoelectric properties over time.
@MyPlayHouse2 жыл бұрын
I do agree :-) this is not a forever trick.
@ianbuenavАй бұрын
@@MyPlayHouse what happens if i try to use this as a forever trick? it wont break the printer, wont it?
@jenssrensen8851 Жыл бұрын
Super, I followed your instructions and now it works again. A slight difference on the positive side. Mine did not burn the 56 ohm resistor
@MyPlayHouse Жыл бұрын
Thanks for sharing,, maybe your resistor was to good..
@jenssrensen8851 Жыл бұрын
@@MyPlayHouse I did not even get hot
@earlfrederick83 Жыл бұрын
thanks morton, for your quick response. that's a very odd solution, but i'll try it. i've never purchased any toner other than samsung toner, but like you said, i've for years (maybe 10??) replaced toners individually, as they've run out. funny thing was, i printed the test page from the samsung website and the colors looked normal! but from my computer (a mac) and my wife's computer (not a mac) the print was yellowish. crazy! thanks again.
@MyPlayHouse Жыл бұрын
I would not be sure that that is the same problem,,, maybe there is a weird setting for colorgrading the prints,, and the printer can be reset back to normal,, like a factory reset.
@earlfrederick83 Жыл бұрын
i think i saw a factory reset somewhere in the myriad of "helps" i've looked at!! i can tell you the i reloaded the printer drivers as well! it'd almost be easier to buy a new printer, but where's the fun in that! ha ha thanks again morton. i'll report back when (if) one of the fixes works.
@carstenhansen39792 жыл бұрын
Stay safe - I would not like to miss my favorite channel due to hacking of $am$ung. It was the last day of April not the first :-) By the way. I still have a 10 years old HP-printer. The only problem is that the ink is expiring. Thanks for sharing video and putting the focus on Printer Recycling.
@MyPlayHouse2 жыл бұрын
I do not understand..
@obtainautomotive883911 ай бұрын
Just another little trick; you can go into Tech mode and reset the counters which negates the need to even need the resistor :)
@MyPlayHouse11 ай бұрын
I have heard about that,, not tried it..
@obtainautomotive883911 ай бұрын
@@MyPlayHouse one for next time 😃
@ВасяЛожкин-в2о2 жыл бұрын
Hello Morten! Great video! But exposing the drum unit to the sun was a bad idea.
@MyPlayHouse2 жыл бұрын
Yes,,, propoly,, no damaged registered.
@d.j.black.spyros Жыл бұрын
It's OK for a short time ... Of course it's better to cover it somehow ....
@MrJesus41948 ай бұрын
Thank you. It worked perfectly.
@MyPlayHouse7 ай бұрын
That is awesome!! thank You for letting me know.. :-)
@annelihartmann5050 Жыл бұрын
Worked!! Thank you SOOOO much! Easy to follow directions. Perfect from first page printed after this "reset"
@MyPlayHouse Жыл бұрын
You're welcome! happy to help!!
@CrayZeeOfficial Жыл бұрын
I have replaced this once already and it wants replacement again. I did by NO means get the 16000 pages out of this at any time, I end up getting forced to change this about every 2 times as I change toners. Awesome hack indeed.
@MyPlayHouse Жыл бұрын
Hope it helps you,, remember to use a week resistor :-) it needs to "blow" a little like a fuse but with the right amount of power.
@ToggaphdeDratersi10 ай бұрын
I couldn't get my hands on a 56 Ohms resistor, so I used a 68 Ohms one and it worked. It seems that using a resistor near 56 Ohms is enough. And yes, it burned as it was supposed to.
@MyPlayHouse10 ай бұрын
Cool,, it just need to see a connection and not see a connection,, without breaking the system that does that.
@pepiguillen89476 ай бұрын
Superrrr I did follow your instructions and I was able to fix it! thank youuuuuuu
@MyPlayHouse6 ай бұрын
Glad it helped! You are very welcome..
@jjjacer2 жыл бұрын
if i remember my laser printers besides storing excess toner in this model, the imaging unit uses static to hold the toner to itself and then using a corona wire it can transfer the toner to the paper before going through the fuser to melt it to the paper. im guessing over time the imaging unit starts to have issues holding that static charge and the image quality can go down over time. (i also think i was told back in the day to not expose it to sunlight or touch it much either. But that was also i think the older toners with the build in imaging roller)
@MyPlayHouse2 жыл бұрын
Hi jjjacer Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@earlfrederick83 Жыл бұрын
Excellent explanation of the fixes! Have you ever had the problem with your C480 where prints come out with a yellow cast to them? That's what i'm going thru right now. I've replaced the drum and the feed belt (over $200) and still the yellow persists.
@MyPlayHouse Жыл бұрын
Yes I have had issues when i switch from original toner to copy toner,, and I change them one at a time,, as they ran out.. and only when they was all change, the prints looked okay again.
@255662 жыл бұрын
Do not vacuum toner with a regular vacumm cleaner, the filters aren't enough to keep it contained and you will spread it everywhere in the air. There's a special vacumm for toner accidents
@MyPlayHouse2 жыл бұрын
That is a bloody fine powder :-/
@giornikitop53732 жыл бұрын
you need a vacumm with special filters. toner is also very toxic (if not melted in the fuser), as it's so fine, it can go through the pores of your skin. it goes without saying you should not inhale it or get it in your skin. better work in an open area or wear mask when dealing with it.
@Fifury1618 ай бұрын
@@giornikitop5373 Wrong, toner is not toxic, it is an inert fine powdered plastic. The black toner is usually made from carbon black, titanium dioxide and silica. The colours composition will differ between manufacturers. It has been suggested that due to the small size of the particles that it could potentially be carcinogenic
@abdulrazakbahrami6 ай бұрын
So I had the container with the powder the one with the yellow, red, blue and black spilling everywhere, which I cleaned it all, but then installed everything back and it said it needs toner, is my printer still okay and only needs the toners or you think I ruined it?
@chrisleonard73776 ай бұрын
worked perfectly, thank you !!!
@MyPlayHouse6 ай бұрын
You are most welcome!
@petrabergmeier2517 ай бұрын
Thanks a lot - it works perfect!👍
@MyPlayHouse7 ай бұрын
You're welcome!
@wedsafer7187 Жыл бұрын
How can I connect wireless? Please help for print Samsung c460w
@MyPlayHouse Жыл бұрын
I would recommend to connect to the printer with a network cable from a laptop. There is an build in web interfaces, where you can then give your printer access to your wireless network,, or set it up as a standalone wireless thing. It can be difficult..
@nodinosaurshere648310 ай бұрын
Do you have to empty the drum though?
@MyPlayHouse10 ай бұрын
You,, should,, at some point it will be full,, and mess with you.
@koosjorritsma6314 Жыл бұрын
Thanks, I needed this!
@MyPlayHouse Жыл бұрын
You are so welcome! I am so happy to be able to help extend the life of your printer,, or postpone an irritating expense 🤔
@shirishjadhav6457 Жыл бұрын
Hello Let me know how to reset the Samsung 3320dn printer errors.red lite blinking
@MyPlayHouse Жыл бұрын
Sorry I have no idea..
@diegomeirelles2011 Жыл бұрын
Thank you! Nice trick. Have you tried those hacked firmware for 100% toner(for diy Refill)? Greetings from Brazil!!!👽
@MyPlayHouse Жыл бұрын
I did see that there was other ninja hacks..
@Google_Is_Evil9 ай бұрын
That imaging unit is light sensitive. You really don't want to expose it to direct sunlight.
@MyPlayHouse9 ай бұрын
I know,,, hard to show it to you much, but keep it in the dark...
@carolaankar2436 Жыл бұрын
Seriously dude... you rock TYVM 🙌🙌🙌
@MyPlayHouse Жыл бұрын
Thank You! I hope you safely hack your printer,, and postpone the larger investment :-)
@carolaankar2436 Жыл бұрын
@@MyPlayHouse Oh I will love my new hobby, trying to understand and hack the living c*** out of this printer. And it's not "being cheap" as you put it, it is pure self preservation you are doing both environmentally and financially. You literally are about to save my life with this and I am not kidding you, so you rock beyond words for real. TY🌹
@axelf1234 Жыл бұрын
Hi Morten Is ist necessary to close the printer in order to start the resistor burning or can I leave the front open?
@MyPlayHouse Жыл бұрын
I could only do this once,, I do not know! in 15.000-20.000 prints I can try again :-/
@axelf1234 Жыл бұрын
Hi Morton. This hack is so good that I want to add my findings. I twisted two wires around the pins and pulled them out under the front door above the paper tray. I measured 3V. The right pin seems to be GND. When opening the door the Voltage drops. Connecting the 56ohm resistor with the door open makes the voltage go to 0V. Closing the door, starts all: the voltage goes to 3V and soon after it went beyond my scale of 20V! My 0.1W resistor got burnt outside and away of anything else that could melt. Then the printer started up and calibrated the density. On the pins I soon could measure 3V again. I assume this is for detection of a new imaging unit, because someone might need to replace it for other reasons.
@Meximat2 жыл бұрын
Worked for me👍
@MyPlayHouse2 жыл бұрын
Glad to hear it! I do like little hacks that saves me money;-)
@ScottDowneywoundedbear2 жыл бұрын
You should never expose the drum to light, it will shorten the life or damage the drum. Its like film, you need to work on it in low or no light.
@MyPlayHouse2 жыл бұрын
Hi Scott Downey Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@DonBishopDonSongs2 жыл бұрын
Hi Morten, that's Cool!:) I have never had a Samsung Printer. But I have several HP Printers, Scanners and Combo units. And an Epson combo unit. A Laser Printer. Also, some older Serial Port Printers, in the Garage. All of which, are throwing errors of one type or another. I wonder if, any of them have this Resistor setup in them. One of these days, I need to check into that... I also have an HP Flatbed Scanner, that still works perfectly, it's 10 or 15 years old. And a Serial Port Flatbed Scanner, that only works up to Windows 98. I Worked perfectly when Parked, in the top of my closet... Don
@MyPlayHouse2 жыл бұрын
Well if your stuff works,, there is no need for a fix,, but the day may come :-)
@DonBishopDonSongs2 жыл бұрын
@@MyPlayHouse Yep, that day always arrives:) Don
@windowsvista86282 жыл бұрын
hey Morten what kind of Windows Server you recomend for IBM System X3550 M2 "Model Name 71G"?
@MyPlayHouse2 жыл бұрын
Server 2019
@windowsvista86282 жыл бұрын
@@MyPlayHouse thanks!
@user-bq2vf6ld7w Жыл бұрын
❤❤❤❤❤
@MyPlayHouse Жыл бұрын
Hi @user-bq2vf6ld7w Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@sirinechouli38732 жыл бұрын
should the resistor be 2 watt?
@MyPlayHouse2 жыл бұрын
No,, it is meant to burn off,, so do not make that any harder. It sees the resistances and reset the counter,,,
@sirinechouli38732 жыл бұрын
@@MyPlayHouse i tried it, smoke was coming out of the printer so i removed it immediately. i used a resistor of 56 ohm and 0.25 Watt
@sirinechouli38732 жыл бұрын
but it did not work, any ideas?
@Mikeruzaryu Жыл бұрын
2:25 If that recipe is dirty I need to buy another one?
@MyPlayHouse Жыл бұрын
I think you can empty it and clean it with an air compressor.
@elminster81492 жыл бұрын
ma jen ta = magenta, s-eye ann = cyan :P
@MyPlayHouse2 жыл бұрын
Thank You.
@N수생2 жыл бұрын
Samsung printers,.. i see them everywhere
@255662 жыл бұрын
Samsung printers was bought by HP so you will still see them everywhere in the future
@MyPlayHouse2 жыл бұрын
I do not know anyone else that has one, before I bought mine.
@MyPlayHouse2 жыл бұрын
Sad day.. :-/
@Dinur36 Жыл бұрын
It does not work for me, i've tried with a 50a fuse, and the only thing that it does is restarting the printer, i mean it starts, it says initialize then it restarts, and the fuse does not blow, i doubt that with a 56ohm that's equal to 56 amps it will start normaly, any tips for me in this case?
@MyPlayHouse Жыл бұрын
I do have a sugestion,, go to who ever leaned you anything about electronic and ask for ALL your money back! I used a 56ohm resistance witch is like 1/4 watt,, so if the printer uses 5V this resistor would probably quit at 100-200mA,, if the voltages is higher the amperage is even lower,,, and you think it will blow a 50A fuse :-/
@Dinur36 Жыл бұрын
I've manage it to reset via Tech mode in the menu, full printer reset and counters reset, and cleaned the drum unit. Worked perfectly without having to use a resistor.
@matthewlandon16972 жыл бұрын
First
@MyPlayHouse2 жыл бұрын
Matthew Landon is again awesome first! I am on my phone,, sorry 😬
@matthewlandon16972 жыл бұрын
@@MyPlayHouse no worries
@femellechatqueen Жыл бұрын
I have a samsung clx 3305 fx that would give me the error of replace drum unit and all i use to do was empty that excess toner on the side of the toners that worked for many years but somehow today my error showing prepare new imaging unit. I watched a few videos and i recall one guy taking the whole imaging unit apart to empty that large tray of toner the same area were you drilled holes I sorta like your shortcut to this less work and pretty well same results I will be trying this and see if that is all I need to do I might have to purchase that 4pcs Imaging Drum Unit Chips CLT-R406 for Samsung CLX-3300, 3305, C460FW Xpress for 28 bucks I will see after I do the holes with a soldering gun like someone suggested in your comments , I was also thinking what if the drill sends debris inside that compartment I do really like the soldering gun idea. I was just confused why one error msg said replace the drum for years and today i have one saying prepare new imaging unit...would you know what the diff was ? Ps i enjoyed your video
@MyPlayHouse Жыл бұрын
Thank You! No sorry I do not know what the differences is. :-/
@femellechatqueen Жыл бұрын
@@MyPlayHouse I replaced the chip and its been working since thank you
@x914pqmm5 Жыл бұрын
Yes, I followed these directions exactly, emptied the toner waste tanks (messy messy messy) and added the 56ohm resistor. Shut the door, started up the unit, let it cycle. Turned off, opened door, resistor was burned. Now it works. I found the resistors on ebay for $3 for a pack of 10. My C430w did not have the 'chip' in the imaging unit, just like the unit in the video. Worked perfectly.
@MyPlayHouse Жыл бұрын
Maybe tape the remaining 9 resistors to the inside of the printer,, for next time :-) Thank You for letting me know that it worked!
@kupothechocobo10 ай бұрын
My C430W did not come with the chip and the technique still worked! I was able to carefully tape the resistor the correct two pins, put everything back in, powered up the system, the system burnt out the resistor, and then I took out the resistor. It worked perfectly.
@artursmihelsons4152 жыл бұрын
Thanks for sharing ninja hack! 👍 This may be useful! Great video, as always!
@MyPlayHouse2 жыл бұрын
Hi Arturs Mihelsons Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@mfeldheim3 ай бұрын
So awesome! I had a similar thought process to clean out the toner from the imaging unit, and found your video on how to reset the counter. Didn't have 56 Ohm but 2x100 Ohm in parallel worked as well. Just wrapped them around the contacts leaving everything in and closed the door, red light came on, the resistors got warm and didnt burn through, removed them, it will do a clean cycle for each toner color and then the counter is set to 0. Wondering how the other counters can be reset.. but that's a problem to worry about in the future - for some reason the other counters were much lower
@MyPlayHouse3 ай бұрын
Glad to hear it worked,,, I would not recommend the 2x100 Ohm in parallel,, as the power they can handle dobbel,,, and something else might not handle that.
@Eo_Tunun2 жыл бұрын
I have never tried to trim a 500Kohm poti to 56 ohms, but one wouldn't even have to burn a resistor if a poti trimmed to that value was attached and when it shows the first sign of warming gets turned to 500K again. The electronics should read that as a burnt resistor as well! That's a neat hack! ^^)
@MyPlayHouse2 жыл бұрын
Hi Eo Tunun Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@MrAlex34612 ай бұрын
Danke :)
@MyPlayHouse2 ай бұрын
You’re welcome!
@DanielsThierry8 күн бұрын
do you have experience with the fuser as well?
@MyPlayHouse3 күн бұрын
No,, not yet :-/
@zx8401ztv2 жыл бұрын
Im surprised that samsung would do this to there customers, its sabotage to get more money. Rather than use a resistor, use a pozistor or thermistor or similar to allow the printer to see the value it expects for a few seconds. When cool, the resistance is back to a new value. Or a small bulb? lol
@MyPlayHouse2 жыл бұрын
Or just burn a resistor,,, and be okay for years to come.. :-)
@zx8401ztv2 жыл бұрын
@@MyPlayHouse Yep that's true, i was trying to think of a proper fix for there sabotage. Anti tage lol.
@bjdchwr2 жыл бұрын
We have some Samsung printers at my workplace (in the teachers' office) and we generally don't like them. I would personally recommend brother in terms of the compatible toners on the market. Samsung printer usually requires a longer warm-up time before each print and the long term lifespan is not as good as HP or Brother printer. HP printer is okay but their consumables are also quite expensive, plus the web interface to set up email scanning is very buggy with Office 365 email setup.
@MyPlayHouse2 жыл бұрын
Okay,, I deliberately did not pick an HP,, as the lifespan on the toners and prices of them was higher.
@giornikitop53732 жыл бұрын
modern "consumer" HP models are terrible in every aspect. only the expensive ones tend to last a long time.
@zdenekeger2850 Жыл бұрын
Perfect video, thank you a lot 👍
@MyPlayHouse Жыл бұрын
Hi Zdeněk Eger Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@Ahmed-gm8li2 жыл бұрын
2nd xD
@MyPlayHouse2 жыл бұрын
Hi Ahmed Thank You very much! glad you liked the video :-) Thank you for watching! :-)
@renzopedroia2 жыл бұрын
Le devo un favore. Grazie grazie grazie.
@MyPlayHouse2 жыл бұрын
HI Renzo Pedroia My channel is English, and to make sure as many as possible, can also enjoy the comments, they are also English. Please keep to English. Thank you for watching! :-)