Samsung LED TV blinking red light indicator.

[@VenkatesanS]

6 months you were thinking and got it solved!! Great.

[@tevzTVTevatronics]

Hahahaha

[@tumertech4609]

It was a joke🤣

[@tevzTVTevatronics]

@@tumertech4609 yes it is.

[@nowemmarkez1767]

Come on man.. it was only 6 minutes.. 😂

[@tevzTVTevatronics]

@@nowemmarkez1767 hehehe😄😄😄😄

[@sarockpashotan]

Hi dear tevz. These days I was sick so i couldn't watch your previous video a TLC tv.but i did watched both and i will Wright separate comment for each. This video was great but i can guess it took much time to find the leaky mosfet.and made you a lot of trouble.!!! But you proved there is not any issue of defective tv can not make you tired or resist you of repairing that and always you are a winner so i proud you very much. Iam so glad to have you my dear friend.

[@tumertech4609]

I think the "6 MONTHS LATER" was a joke😂

[@tevzTVTevatronics]

Its a joke hahaha

[@tevzTVTevatronics]

Thanks for the support. Get well soon.

[@pareko40]

Salamat sayo sir. Na ayos ko ang tv na ginagawa ko dahil sa video mo👍👍👍

[@electrolatif]

You are the best always. I find Samsung smart 4k😂😂😂, i find 13v not stable, i disconnected the power board and test again 13v, and still not stable. Now i try to find the problem. Looks easy when we see you fix tv but in the reality need experience 😂😂😂😂

[@mohamedgendy4649]

A video full of valuable information. Thank you, Mr. Tevz❤❤

[@arnieworkoholik6883]

Bravo, in Europe we would change the Board, you repair it,well done

[@sicretservice]

В Европе его давно бы выкинули.

[@santos275]

En usa 🇺🇸. Too

[@zembmule1926]

king of electronics✊

[@pedro_franco]

One of the few videos that explains the diagnostic process. Thank you 🙏

[@SavaliyaAlpesh]

Hi Tevz sir your fault finding technique is really amazing then other technician on KZbin.... Love from India🇮🇳❤

[@Ochitonde]

Tevs, you are a wizard. After 6 months you got it right. Thanks for the information

[@scamsuncensored7740]

When you get a soldering iron, practice with it until you get good at soldering. Same with a heat gun, and, get all the tools you need to do good soldering and heat gun work. Nice job TEVZ.

[@gayanherath6901]

Thank you so much, I solved this problem using your video. 👍

[@tevzTVTevatronics]

Great!

[@GreenGuyDIY]

Interesting. You have awesome, infinite patience. Hopefully it is OK if I impart a few tips. #1 while going through supplies it always good to follow the supply through switching points to start with. Would have saved a lot of time. #2 EEPROMs rarely change programming in circuit by themselves so chances that it is corrupt are very low. I would have saved that for last unless the user reported that the power was pulled while updating. #3 why not use the programmer verify before re-writing just to be sure you really need to re-program it? Or download the image and verify it against the known good image? In any case nice work!

[@tevzTVTevatronics]

thanks

[@jmikronis7376]

Infinite patience on one piece of equipment, as a repair tech will get your fired. Infinite patience while being an electrical engineer is what you’re supposed to have.

[@sumanmadipelly256]

Great job sir 👏

[@varindraelectronics1464]

Good informative clip..

[@angelosanagnostou5550]

I am glad to see that I am not the only one that gets a tv fixed "6 months later". I laughed, because I know the feeling.

[@jmikronis7376]

Working on it for 6 months is a good way to build up frustration and quit the field. If only the manufacturer would share their info on what normally goes bad on models.

[@jaylasquety8701]

WOW I'M AMAZE... THANK YOU FOR THIS VIDEO👍

[@NorlysHernandez]

Good job Master and nice video 👍👍👍

[@CyberPick]

10:05 dirtiest ic programmer of the whole KZbin ever :o but great video, thanks :)

[@tevzTVTevatronics]

HAHAHAHA

[@jmikronis7376]

His job is not to keep the tools of the trade clean.

[@mohamadounajjibou9822]

Good leason in our own terms we would have changed the Mother board ❤❤❤

[@na90sa]

Very informative video, you are awesome 😁 Make more videos!!! 🤩

[@Le_vis254]

Thanks for the video. I have finally found the best channel..Do you have a video where you have explained parts of the tv motherboard components and how power is distributed in the motherboard kindly? I want to start from there for a good foundation

[@Purestones]

your video very helpful thank you so much.

[@ГузенкоВиталий]

Дякую вам. Гарна робота.

[@GoogleEarthfact.]

Good job sir ❤

[@ourmedia2362]

You are talented

[@plexi-k3d]

Good repair video!

[@vhbtechtv8941]

tevz is the master of all master in electronucs

[@rizallatiff3566]

Great job boss

[@pudarisaikrishna8879]

Nice work

[@prakashfulzale7642]

Engineering sahab.

[@juanpacris2290]

thank u sir tevs verry clear

[@nowemmarkez1767]

Great job sir..

[@martinllagers8364]

hola saludos desde argentina . deberías poner el modelo del tv en el titulo para que se encuentre tu video mas facil

[@Nature72116]

Leaking MOSFETs? 😊I will remember to use a towel for that leaky MOSFETs...😅

[@tevzTVTevatronics]

😅😅😅

[@mustaqahmed4896]

Good idea sir

[@mylenerodriguez6684]

thanks 👍👍👍

[@tevzTVTevatronics]

Welcome 👍

[@clementgavinala237]

Thank you teacher

[@protection4541]

Hello Did you short-circuit the D and S pins for a moment and the TV turned on?

[@tevzTVTevatronics]

yes

[@protection4541]

@@tevzTVTevatronics Does this not cause damage to the circuit?

[@tevzTVTevatronics]

@@protection4541 No because the MOSFET duty is to short the drain and the source or act like a switch.

[@protection4541]

@@tevzTVTevatronics Is it possible to do this wherever there is a mosfet for a momentary test?

[@tevzTVTevatronics]

@@protection4541 big no

[@Dr-Youtuberl-32]

Good job 👏

[@lakshaniishanka-i9z]

Hello sir. great video. wish you to go further . if you can send some firmware bin i really appreciate about it and i will help for me

[@rajeshjadav1240]

Thank. S. Good. Day

[@aminulvivo1420]

Nice video

[@golge2828]

👏👏👏

[@maxwarfield6699]

At 12:59 you say “let’s try to connect the gate to the source” but the drawing shows a red line, connecting the drain to the source. So, which is right, the drawing or what you are saying?

[@tevzTVTevatronics]

The drawing is correct. the narrator is wrong. I wrote the wrong pin of the Mosfet creating the narrator's voice. You're really paying attention to my video thanks for that.

[@maxwarfield6699]

@@tevzTVTevatronics Well, I’m learning a lot thanks to you so, thank you kindly.

[@alikareme2375]

very good

[@Rahulelectronicsworld]

Thanks for sharing 👍👍

[@NazarethJimMojah-xn6oc]

Hi tevz, I want you to educate me on flash programming, am using TVP2588U+ programmer but finding it difficult to reprogram. Please any video on flash programming?

[@pradeepkumard9682]

Sir how to make flash ic programmer and programing method pls video make

[@Bambangsugiarto67]

Tank you🙏👍

[@KumaraSarath-gz9bv]

Exellent .....

[@tonieronvaldez]

While you using hot air working instead lower the heat and same as air flow that bloated pcb

[@jmikronis7376]

He should use some Kapton tape (expensive) to shield the board from the excessive heat.

[@arielrojas9349]

Ese es el verdadero cacharreo, A+++++++++ para ese tecnico

[@powerbord6002]

سلام مستر توز من خیلی کانال شما را دوست دارم متاسفانه انگلیسی بلد نیستم خودم هم تعمیر کار TVهستم دوستون دارم ❤❤❤❤❤😂

[@rkteam3132]

Super ❤

[@tevzTVTevatronics]

Thanks 🔥

[@leevan1424]

hhh 6 months after thank you ...

[@electrolatif]

Take 6 second to think about it, and 6 min to fix it , and 6 month to forget about it, and 6 years will come back for repair again🤭

[@tevzTVTevatronics]

great 😄😄😄😄

[@hermiemendoza2229]

is there reprogramming or replacement part available for purchase if not available? Can anyone buy mosfet part only?

[@tevzTVTevatronics]

if you can find online.

[@ElectricalEngineering-sx7fd]

I have wondering why you are not using hot air i get it now is there a video for the programing ...are u the one who made that gadget for programing

[@Franklinveterinarycenter1of4]

Tevs, u gonna clean that 10:18 nasty board?

[@artsandeducation7716]

That's all find in is really valuable

[@arifryo6823]

sir can you gave me the ch340 software link. mine always fail to read the original ic. i always buy new one and flash it with firmware from internet. i never succeed with backing up firmware from original tv.

[@LuisHJara]

, muy bueno

[@Josephjohn-v2c]

sir thank you pwede makahingi ng copy ng mga firmware's at link sa software na pang program

[@TheOzthewiz]

The problem is trying to get a hold of schematics for the "disposable" TVs of today! In searching for schematics, all I run across are the "ask a technician" links at $$$$$$$$/minute! I guess THAT is why TVs are disposable. A NEW TV is cheaper than repair INFORMATION! LOL

[@Abdulbasheer26]

Sir, can you say how to download software? which site is genuine.

[@kamalbuddhika6159]

🙏🙏🙏

[@irishguy200007]

The Pink Panther strikes ahgain.

[@huseyintezyal8157]

Mükemmel çalışma

[@ravimali7120]

Where i can get ch341 software

[@tevzTVTevatronics]

Google it

[@niruldesilva3343]

Hello tevz I have issue with lg tv it is only blue screen no picture and this is smart tv I have chage new mother board but still the same any advice how to find a solution for this problem

[@tevzTVTevatronics]

Check panel. Cut ckv line if necessary.

[@mohdkhairudin6936]

Hello tevz. I got a question for you if the mosfet G15N10C got the problem & can't find it. Can you suggest the better one to replace it. Thank

[@khentronics_1990]

hello master ano gamit mong app para sa audio translate at subtitle?

[@tevzTVTevatronics]

windows narrator, yung subtitle ay automatik na sa youtube yan pag english and language.

[@khentronics_1990]

Windows narrator.. sa pc po ba yan

[@khentronics_1990]

salamat idol.. pa support rin po master.. new sa sa vlogging po

[@tevzTVTevatronics]

Oo@@khentronics_1990

[@gabrielcuevas5837]

que interesante programador.

[@campuraduk-24]

👍

[@greendata1]

Pleas use "Solder Paste and Flux

[@wandersonferreira7485]

Você tem algum grupo no telegram? Parabéns pelo seu trabalho 👏🏽

[@suatbulat9599]

👏👏

[@hasantamer9199]

good

[@kdlelectronicstechnology]

❤❤

[@johnwakaba4100]

Software downloading pls help

[@jmikronis7376]

That would be firmware download.

[@زينعساف-ل6غ]

Hey TEVZ

[@Ambo854]

Sit ito samsung tv ko gumagana naman lahat kaya lang minsan pag nag continous blinking ang power indicator nya dina ma control ang mga volume, chanmel pero pag press ng remote control may response naman.

[@ojalesfamily]

Location?

[@ZafarIqbal-qy9qe]

❤

[@kekwwwwhahaha257]

Wow

[@VujkoFrank]

Disgusting working place! Have you seen "Master's" programmer (7:04)?.. The insects are everywhere...

[@nigelpottinger901]

Who taught you you're a professional better than who made them at the factory

[@tanner1985]

15:41 i had a heart attack.

[@bytemyvoid]

omg all equipment really bad, but multimeter is 1600$ ))) hot air gun sounds like membrane pump type - its only good for heat shrink, buy quick 857dw+ and set it to 300 deg C and use widest nozzle (about 1cm diameter) and u will never bubble any board. u are bubbling boards because uve set big temperature (looks like 380+ deg and low flow (maybe because of membrane pump) and really thin nozzle - u are making thermal shock to the pcb because of big temperature gradient (thin nozzle works like rocket needle if u understand me) u need to use 1cm nozzle to heat bigger pcb part so heat will be applied smoother

[@ishkhan2501]

how dirty is this technician?

[@Arie19560902]

Het is gewoon een smerige werker die overal zijn sporen nalaat.