Beautifully explained with simplicity. Generally No doubt left after watching your video. Thanks a lot sir . Normally such type of content with deep clarity and concepts are not available on you tube specifically in regard of industrial equipment problems . Keep it up sir . May God bless you with a lot of success.
@shashikantinamdar660023 күн бұрын
Well explained sir....Thank you
@AlokKumar-gp1sl2 жыл бұрын
most awaiting
@digiraja00732 жыл бұрын
Thank you sir maja aa gaya 👌👌👌👌👌👌👌
@AlokKumar-gp1sl2 жыл бұрын
plz continue and thanks
@VehiclesBro2 жыл бұрын
Thank you so much sir🙏 💐💐Great knowledgeable Video👍
@pramodkushwaha1089 Жыл бұрын
Great Lecture
@shakeelabanu2819 ай бұрын
Good Explain❤❤❤
@aniketsingh8049 Жыл бұрын
Properly explained 👍
@flyingpeople884710 ай бұрын
Thanks sir 😊
@soumenkundu12142 жыл бұрын
Nice .... once again and asusual fine like kerosene....
@gauravjoshi1117 Жыл бұрын
Guru ji 🙏🏻 ko pranaam
@armallick394310 ай бұрын
Amazing ❤
@sabakarim82463 ай бұрын
Thanks for such a detailed lecture!
@virendramourya96454 ай бұрын
Very knowledgeable lecture, thanks sir
@yashakirajapillai Жыл бұрын
Thank🙏 sir
@anilpal59472 жыл бұрын
I got lot of knowledge so thanku sir, please tell me about barrier fluid
@MayankSingh-si8ue3 ай бұрын
Very helpful
@vikingboruah1571 Жыл бұрын
sir please make a video on plan65( a)(b) ,plan66(a) (b)
@PankajKumar-iw5yy9 ай бұрын
Sir Kya isme nitrogen ka pressure Nahi hota hai
@aniketkarmase2 ай бұрын
Can you explain design of mechanical seal?
@rikibora32662 жыл бұрын
Sir, thank u for providing such an important session, plz.. also upload a video in details on plan 53A/B/C.....
@jubermalek5659 Жыл бұрын
Sir. Can i get seal plan notes
@piyushpandey39932 жыл бұрын
Sir mera yaha ek self priming water ka pump hai aur uska mechanical seal ka cooling uske casing se hi ek tapping lekar Kiya hai to ye kaun sa plan hai
@educationwithmd3440 Жыл бұрын
Plan 11
@kuldipsinhrayjada30692 ай бұрын
If there are strainer and orifice both then it is plan 12
@RANJANSHARMA44985 ай бұрын
All plans video
@SandeepAcademy94 ай бұрын
Already uploaded
@Ydv.Chandan4 ай бұрын
Pure seal piping plan total kitane hote hai 117 ya kitana
@bouferkasfarouk9156 Жыл бұрын
Is it possible to change the plan 52 with the plan 53 in an existing crude oil pump knowing that the crude oil contains some salt and sand that block the spring to work properly and make failure in the first stage (tendem cofiguration) and buffer fluid is contaminated quickly ? Can we avoid this problem by plan 53 ?
@SandeepAcademy9 Жыл бұрын
I think plan 53 or 54 would be better choice in this case. Plan 53B is a better choice. However your seal vendor will confirmed.