Harbor Freight Spot welder, first use and thoughts. body panel welding.

Buy One 👍
Thank you for watching. Like and Share. Comment ideas advice what I'm doing wrong or maybe right.
😃Subscribe 👍 Consider a subscription. (its free for an unlimited time😜).
Follow TSR Garage
Instagram / tsrgarage .
TSRGarageUTube
Facebook / tsrgarage1
Music : No Copyright Audio Library
Artist: Quincas Moreira | Track: Chunk
Download MP3 - support.google....
Rock | Funky
Quincas Moreira playlist: www.youtube.co....
#harborfreight #fabrication #tsrgarage #spotwelding

[@beyondmiddleagedman7240]

I've been using one for 3 years now. Jeep and Dodge bodies and stainless brackets for ham radio stuff. Works great. You only need to pulse the switch. And my 3° is 235VAC phase to phase. Works a treat.

[@rickybaez2970]

2 second hold for each spot ?

[@beyondmiddleagedman7240]

That would be 1.5 seconds too long .

[@rickybaez2970]

Really? Wow ok i see so its really tap tap then

[@noahway13]

I like this guy's various jokes (making fun of the unboxing dimwits), he's not a snob who trash talks ALL of Harbor Freight, and his simplicity.

[@TSRGarage]

Thank you. Coming soon to a KZbin channel somewhere. "Getting the box out of my mailbox 📬" videos 🤣🤣🤣.

[@photorealm]

Thanks for leaving your learning curve in the video, I will still probably stick the copper but at least I know that its a timing thing. Confirmed your video. Great viedo

[@jimmytaylor570]

I used the 240 one 8 years ago on my F150, and it worked well 200k miles later, still holding strong.

[@TSRGarage]

Good to hear.

[@manningdriscoll5089]

The 240v works better than the 120v but if you have 3phase service you get 208volt and it dosen"t work very well.

[@aquarius9909]

Another great video. Keep it up. To make good quality spot welds you have to make the welding electrodes to be coaxial when the welding materials are between the electrodes & the proper clamping force is applied. Sparking is not normal and could be dangerous ( proper protective gear is a must ). The factory supplied upper tong end has to be bent more to get coaxial with the bottom end. It is obvious that for every thickness of welded materials you will have to use different diameter / length welding tips & set up their alignment individually. A timer is also a must for good quality spot welds. There are timers with welding time compensation. These are monitoring the welding current and adjusting the welding time accordingly.

[@jraposo911]

I need one of these welders 😊

[@TSRGarage]

👍I wish I had gotten this a long time ago.

[@dennisyoung4631]

The 220 version can *readily* weld 2 1/16 pieces of steel - clean the electrodes, round them off to give a nice *radius,* then a brief pulse gives a nice *small* dot… I have one of these welders, and have tested this matter.

[@dennisyoung4631]

This one needs a precise “pulse timer” to do well on thinner materials. I plan to implement one for mine, in addition to a “stand” to hold it at a precise height and angle. (You need three hands, otherwise, if you’re clumsy like me.) You will also want to carefully file your electrodes every so often for best results. You want a “smooth” flat file, sort of like an old “points file” but bigger, to keep the surfaces of the contact electrodes clean and bright.

[@TSRGarage]

Timer would be great for consistent spot welds

[@richrdwilliams4741]

I might have to get me one of them, for working on a 56 chevy sedan and 46 chevy truck I a building

[@TSRGarage]

I wish I had bought one sooner. It has limited use with the tongs on it, but they can be changed

[@skullhunter9962]

I'm here so early the top video quality is 360p. The video quality should increase the longer it stays uploaded.

[@TSRGarage]

👍👍ya.. The video quality should increase in just a few more minutes

[@trappinout18]

Unboxing footage is a weird fad.

[@TSRGarage]

👍