Seadoo 4-tec Camshaft Timing

  Рет қаралды 80,850

Redrockat

Redrockat

Күн бұрын

Пікірлер: 65
@dioneslima5777
@dioneslima5777 Жыл бұрын
Thx 4 posting
@mauriciorocha2537
@mauriciorocha2537 4 жыл бұрын
Graet vídeo, congratuleations Brazil
@Redrockat
@Redrockat 4 жыл бұрын
Thank you 😊
@nelldantas7413
@nelldantas7413 5 жыл бұрын
Qual o torque de mancal, biela e cabeçote do seadoo 130 gti 2012
@dylanvickers4007
@dylanvickers4007 5 жыл бұрын
I have a head that wasn’t TDC when pulled and I was wondering how I could get the camshaft into time? Will it turn by hand? It’s a complete head.
@Redrockat
@Redrockat 5 жыл бұрын
Whitney Mctopy you will have to remove the rocker shaft and turn the cam with the hand , then you have to replace the rocker shaft and tighten with new bolts .
@tombeckerle7974
@tombeckerle7974 4 жыл бұрын
Redrockat ours is in time, but I have to rotate the crank to free up the engine. Do I just rotate it and move it back? How many revolutions until it’s back to normal?
@edileneneres430
@edileneneres430 5 жыл бұрын
Boa noite! Tenho um sea doo gti se 155 ano 2010, tirei o motor de partida para uma manutenção, e depois que foi colocado no lugar ele gira mas o motor não. Poderia me dar uma dica do que pode ser?
@Redrockat
@Redrockat 5 жыл бұрын
Pablo Engleas
@jefftougint6328
@jefftougint6328 4 жыл бұрын
How many hours can you get out of a modified engine as in this video? Do most rebuild/modified engines fail much sooner then if it was kept stock?
@Redrockat
@Redrockat 4 жыл бұрын
Jeff Tougint the machines lasts as long as the way the operator treats it . I’ve seen machines break due to incorrect operation and maintenance not done and I’ve owned stage 4 machines operating much higher rpm than usual that lasted 400 hours . It all depends on how you ride your modified pwc and this will determine the reliability thereof . Simply put a modified and stock machine lasts the same amount of time when operated correctly and diligently and properly maintained . I hope this helps to clarify , thanks for watching .
@edileneneres430
@edileneneres430 5 жыл бұрын
Good night! I have a sea doo gti if 155 year 2010, I took the engine starting for a maintenance, and after it was put in place it turns but the engine does not. Could you give me a hint of what it might be?
@Redrockat
@Redrockat 5 жыл бұрын
Edilene Neres did I understand you correctly that they replaced or worked on the starter motor ? And when you push the starter button you hear the starter motor turning but the engine does not swing over ?
@Sajadhus19
@Sajadhus19 2 жыл бұрын
After the rebuild I'm getting 100psi compression on all cylinders. Could this be a timing issue. The RPM is also surging during idle
@Redrockat
@Redrockat 2 жыл бұрын
What altitude are you at ? Also have you ridden your ski yet ? What type of compression tester do you have ?
@Sajadhus19
@Sajadhus19 2 жыл бұрын
@@Redrockat I am at 57metres. The ski runs fine during throttle but it struggles to idle for a second and when it finally idles the RPM surges. In land the idle jumps from 1600 to 2200rpm.
@Sajadhus19
@Sajadhus19 2 жыл бұрын
@@Redrockat any clue? Further to my previous comments. I also checked spark plugs and it looks like it's running rich.
@Redrockat
@Redrockat 2 жыл бұрын
@@Sajadhus19 how many hours on the supercharger ? Did you swop out spark plugs with new ?
@Sajadhus19
@Sajadhus19 2 жыл бұрын
@@Redrockat The supercharger was rebuilt 10 hours ago. Spark plugs and coil packs are new. I advanced the timing and the issue has improved (getting 125psi ) . At the moment there's a delay in the motor returning to idle speed after pressing throttle.
@joel8668
@joel8668 2 жыл бұрын
how are is it to replace a timing chain on a 2002 seadoo 4 tech
@Redrockat
@Redrockat 2 жыл бұрын
It’s pretty much involved ... engine comes out crank case comes open engine split so that crank can be lifted so that old chain comes off and new chain goes on . Why do you want to swop out the timing chain with new ?
@davidmcbride2262
@davidmcbride2262 5 жыл бұрын
Hello, do you know of any videos that show how to time the camshaft after a chain has broken and you do not have the witness marks that you scribe on the gear with a sharpie?
@Redrockat
@Redrockat 5 жыл бұрын
David Mcbride you going to do the same as in this video and start with lock the motor with the lock pins . You also need to remove the intake manifold because the one engine lock is under it as well as the tentioner release.
@davidmcbride2262
@davidmcbride2262 5 жыл бұрын
@@Redrockat do I need to pull the engine on a 2015 seadoo gti 130 to replace the timing chain? Any advice you can provide would be greatly appreciated and thank you for the prior response.
@Redrockat
@Redrockat 5 жыл бұрын
David Mcbride yes you have to pull the motor and split the motor
@randall928
@randall928 5 жыл бұрын
Hi, my engine is still in the hull, how do I rotate the engine to line the cam up, so I can insert the locking tool? It is not supercharged. thanks
@Redrockat
@Redrockat 5 жыл бұрын
Liqidarts you just rotate the crank by hand the engine will turn until it is on the right spot .
@randall928
@randall928 5 жыл бұрын
@@Redrockat Thanks, I locked some Vise-Grips on to the drive shaft and rotated it into position!
@Redrockat
@Redrockat 5 жыл бұрын
Liqidarts awesome 😄
@jhonatanramos4856
@jhonatanramos4856 4 жыл бұрын
Hello I have a 07 180 challenger that runs too rich, vibrates a lot and runs very rough, changed spark plugs coils, voltage rectifier throttle body and some other sensors and still doing same thing, you think the timing has jumped in it, it also says low voltage on the dash but seems to be getting 13 volts all the way around please help
@Redrockat
@Redrockat 4 жыл бұрын
What is the condition of the supercharger ? Did you change out the map sensor ?
@jhonatanramos4856
@jhonatanramos4856 4 жыл бұрын
I don’t know the condition of the supercharger, how can I check that? And I believe the map sensor was replaced when I took it for throttle body get replaced
@Redrockat
@Redrockat 4 жыл бұрын
@@jhonatanramos4856 you will start with removing the air intake side on the charger and visually inspect the super charger impeller for rust and fatigue . Check if the supercharger impeller has tention on it . If it has no tention and there is no slip tention then the supercharger washers have broken . The timing can’t really just shift on these motors but your cam gear ⚙️ may have come loose so check that also .
@jhonatanramos4856
@jhonatanramos4856 4 жыл бұрын
Thank you very much man I’ll check that tomorrow afternoon
@literbikedoc
@literbikedoc 7 жыл бұрын
What chains do you use Red? I'm hearing a lot of chain failures in 05 to 07 215hp engines at under 100 hrs
@Redrockat
@Redrockat 7 жыл бұрын
literbikedoc all the oem chains are very good and do not break . But ... specifically 05 to 07 skis throw ceramic washers and they land right in the chain first and get crunched up by the crank chain gear leading to a chain failure . I have had turbo 2005 skis and rpm at 10500 with no problems on the chains . Ps - only use oem BRP chains there is nothing better .
@clayhunt1284
@clayhunt1284 8 жыл бұрын
thank u very much .. well done
@Redrockat
@Redrockat 8 жыл бұрын
Thanks 😄
@tommyg33s
@tommyg33s 6 жыл бұрын
A quick question, do you know the rotation of this engine when it is running?
@Redrockat
@Redrockat 6 жыл бұрын
tommyg33s the rotation direction is clockwise
@tommyg33s
@tommyg33s 6 жыл бұрын
@@Redrockat is that from the flywheel side?
@Redrockat
@Redrockat 6 жыл бұрын
tommyg33s yes for sure it is from the flywheel side .
@supremo2224
@supremo2224 7 жыл бұрын
Hi good day I want to ask you a question about my rxp215 2006 that I bought used not the hours you have or the maintenance that you would have done. The bike works very well. After one of the last mounted out of the water I make a control of everything and I find that the tank of the refrigerant system has oil. I wonder if this situation happened to you and if you have any information about it. From already very grateful and very good your video.
@Redrockat
@Redrockat 7 жыл бұрын
Hello ,yes I have had this problem before . It is your oil cooler that is suspected of leaking oil into the cooling system . replace tha oil cooler 😊
@supremo2224
@supremo2224 7 жыл бұрын
Okay, I'm going to take it apart and then I'll tell you. Thanks for your answer.
@Redrockat
@Redrockat 7 жыл бұрын
+supremo 222 cool stuff 😊
@supremo2224
@supremo2224 7 жыл бұрын
Hi, my friend, and checked the oil radiator and it's okay, you have some suggestion to look for, from many graces.
@Redrockat
@Redrockat 7 жыл бұрын
+supremo 222 it could be the water pump ,but not likely. I would clean out all the coolant from the system ,flush the system then put new coolant . ride it like that and see what happens .
@خالدالاحمدي-ظ5م
@خالدالاحمدي-ظ5م 2 жыл бұрын
Hello my dear brother, I want a Jet Ski Seado RXP 2010 X how much money I am from Saudi Arabia
@Redrockat
@Redrockat 2 жыл бұрын
Hello Brother , are you purchasing it in Saudi ?
@خالدالاحمدي-ظ5م
@خالدالاحمدي-ظ5م 2 жыл бұрын
@@Redrockat
@Redrockat
@Redrockat 2 жыл бұрын
@@خالدالاحمدي-ظ5م I don’t have a 2010 at this moment only a 2022’ Sea-Doo 300 Black Edition if you interested ?
@gta5gameplay300
@gta5gameplay300 7 жыл бұрын
does the cam go in one way for the locking tool
@Redrockat
@Redrockat 7 жыл бұрын
Yes
@gta5gameplay300
@gta5gameplay300 7 жыл бұрын
the cut out in the cam is were the locking tool go,s????????
@Redrockat
@Redrockat 7 жыл бұрын
+GTA 5 Game Play yes
@PaceandPower
@PaceandPower 2 жыл бұрын
Hi there
@Redrockat
@Redrockat 2 жыл бұрын
Hello 👋
@naziruddin7276
@naziruddin7276 2 жыл бұрын
.
@rahimlotfi9540
@rahimlotfi9540 4 жыл бұрын
Kawasaki ultra 260x
@Redrockat
@Redrockat 4 жыл бұрын
Cam shaft timing on the Kawasaki Ultra 260 is easier. There are dots to be lined up and you count the chain links and it's done .
Sea Doo Jet Ski Supercharger Failure Aftermath Part 1 of 4
6:55
I was just passing by
00:10
Artem Ivashin
Рет қаралды 18 МЛН
What type of pedestrian are you?😄 #tiktok #elsarca
00:28
Elsa Arca
Рет қаралды 37 МЛН
MIND BOGGLING ENGINE GEOMETRY - Rod Ratio Explained
18:43
driving 4 answers
Рет қаралды 6 МЛН
TOP-10 UNRELIABLE DIESEL engines. Subtitles!
20:30
АвтоСтронг-М
Рет қаралды 2,1 МЛН
Замена цепи на ROTAX 1503
9:33
Feo-Sea
Рет қаралды 21 М.
Engine Sensors - Basics. 3D Animation
16:19
CARinfo3d (En)
Рет қаралды 651 М.
Contact Patch & Pinion Depth Explained
7:17
DrivelineMaster
Рет қаралды 606 М.
Seadoo GTI, GTX , Head torque
7:04
Leo marrero
Рет қаралды 544
I was just passing by
00:10
Artem Ivashin
Рет қаралды 18 МЛН