Francesco, boa tarde. Você teve ótima idéia de fazer o suporte para colocar os tirantes. Parabéns. Ótimo vídeo. Muito bem ilustrado. 73. Francisco-PY2NF.
@iv3tmm13 жыл бұрын
@QRPPPSK31 Hi Jack, tnx fer QTC. You welcome. If you have to setup an R8 remember: Set up/dwn stub for 6-10-12-15 m (i had to increase with a new stub +20cm the stub for 15m). Set up/dwn the connection under the 20m trap coil for 17m, not so long but you can move some cm. 20m - you can' t do nothing, only mods lenght of coil trap. 30m - you can cut or change the connection between the two traps (i had to cut 10 cm of alluminium tube for 30m SWR) 40m - tune the last stub on top of R8.
@giorgioermacora39997 жыл бұрын
Complimenti un bel lavoro! IV3GNE
@Thegoldenoldiegamechannel-e3m10 күн бұрын
I have the R9 good antenna but Wonder what will happen to Cushcraft antennas now MFJ is winding down !!
@sirhenry.overlander5 ай бұрын
Great job. How is the R8 Crushcraft? Did it work until now? Do you have a draft from the construction? VY73 de DO1DPL
@captain-Luca-is0hmz6 жыл бұрын
Ciao Francesco, personalmente ho sempre preferito non controventare le antenne per farle curvare con il vento ed evitare che si spezzino, tu hai trovato vantaggi? Io a breve monterò la R9 73
@JCB12345 Жыл бұрын
Hello, I was facing problem with Cushcraft R9 on the 80 and 4om tuning. Hard to find proper point on the coil to place the tapping pin. I want to make 3.573 for the 80m and 7.074 on the 40m Loading coil. Meanwhile for another band I got better SWR. I was using RigExpert A55 Zoom. Dou have any advice or video for adjusting the taping?
@IV3CYZ12 жыл бұрын
Complimenti, ottimo lavoro, bellissima antenna! Bruno
@iv3tmm13 жыл бұрын
@fasthandslow Just trying it since 08 July on all bands. Great antenna. If the location is open to the skyline you will not have any problems to work DX station. Have worked CX ZP PY in S.A., VK9H 40m in OC, JX EU. no problem very close, ST0 in AF, some trouble with VU direction because i have mountain, no prob with JA AS., caribean sea and so on. Runing an Icom IC-7700 with his output power ... 200 Watts, don' t use any amplifier. Stay tuned ... gl gdx 73 de IV3TMM.
@fasnuf3 жыл бұрын
Wow. big job
@iv3tmm13 жыл бұрын
@brubatt Le fascette a croce per gli occhielli dei controventi non sono isolate dai tubi in alluminio della R8 ... non interferiscono. L' importante è che gli occhielli del fili in teflon non tocchino i vari stub altrimenti andrebbero in corto con il tubo principale. Ciao 73 de IV3TMM.
@iv3tmm13 жыл бұрын
@QRPPPSK31 Hope that you will set up a good antenna. Ciao Francesco. Stay tuned ... will be active as 9U3TMM at the end of the year.
@bastyon7512 жыл бұрын
Nice job. I like it.
@fasthandslow13 жыл бұрын
Hello, Great video, hopefully the R8 will be my next antenna. I’m very impressed with the guy wire support frame at the base of the antenna. How is the R8 performing on dx and what radio do you use? 73 de M3MQR
@iv3tmm13 жыл бұрын
, but probably this way will change the 17m swr, be careful In this case you have to open the coil trap, it’ s a bit difficult but not impossible, good luck HI For 30m is the same way but in this case you can cut or alonge the tube between the two coils trap. In my case i cut 10centimeter the tube between the two coils trap. I suggest you to check very well the lenght of all alluminium tubes then tune ONLY 20m.
@peteluetz25869 жыл бұрын
Great video. Can you tell me about the guy wire base? IS this custom designed or is there a company or person who manufactures these? If not, are there drawings of the guy wire base design?
@iv3tmm9 жыл бұрын
Pete Luetz It' s custom designed, send me your e-mail i will send you drawings. Ciao. IV3TMM
@a45wh9 жыл бұрын
+Francesco Crosilla (IV3TMM) very nice pls send me the drawing to vu2sdf@yahoo.com 73 san a45wh
@xen66668 жыл бұрын
+Francesco Crosilla (IV3TMM) Nice job! Please send me the drawing too. ur7tt.ua@gmail.com
@Joe260038 жыл бұрын
Nice work! Any chance you could share those drawings with me. I would appreciate it. email: wh6qv@aol.com Please put your call sign in the subject line.
@johntaylor12448 жыл бұрын
KJ4CGG I would also like drawing for the base of the R8 Kj4cgg@gmail.com thanks John Taylor
@brubatt13 жыл бұрын
ciao e complimenti volevo sapere cosa hai utilizzato per isolare le fascette dove hai attaccato i controventi 73 de bruno iw5ejp
@antreasstathas165 жыл бұрын
Vice job....besttttt
@alphasxsignal7 жыл бұрын
Nice install
@st8kout9618 жыл бұрын
While I'm no expert, I'm surprised you'd want a vertical, being so close to a hillside, unless that direction is not important. On the ground that looks like it would be a kid magnet. "Wow, lets go climb that pole."
@alphasxsignal7 жыл бұрын
How is the antenna working for you? Do you have some videos of you using it on the air???
Thank you so VERY much for sharing the design with us!!
@captain-Luca-is0hmz5 жыл бұрын
A distanza di 6 anni.... raccontaci... Io avevo la R-9 purtroppo l'ho dovuta levare perchè non potendo mettere stralli oscillava parecchio e i vicini avevano paura, per il quieto vivere ho cambiato. A me ha regalato tante soddisfazioni
@cd11686 жыл бұрын
what is your location? is it italy?
@iv3tmm13 жыл бұрын
After 20m swr is OK, then check again your swr on 30m and then tune 30m. Finally check again 40m swr and tune it. It ‘ s a long way but this is the ONLY RIGHT way to tune R8. I immagine that 6/10/12/15m swr is OK. Hope that you will tune your antenna. 73 de Francesco IV3TMM and tomorow on trip to Burundi operating as 9U3TMM for one week, stay tuned. Ciao.
@SP9DLM11 жыл бұрын
hello :) I ask you, what is the length of the horizontal arm at the base of the mast extraction sp9dlm
@iv3tmm11 жыл бұрын
Ciao, grazie del commento. Buona attività in radio, spero di collegarti. 73 de IV3TMM.
@gianluigiviola111 жыл бұрын
Ciao francesco, complimenti per l'eccellente tuning della R8, che spero di poter utilizzare anche con la mia antenna.Come ti dicevo prox volta che rientro da Mosca ci vediamo per chiarimenti.Ti ho inviato mia mail via SMS. A presto 73
@iv3tmm13 жыл бұрын
PY2DS wrote Hello Francesco. My name is Murilo (py2ds), i bought a Cushcraft R8 in last mounth because i see your vídeo in youtube. Is a very good antenna but my SWR in 20 and especially in 30 meters is high. How i adjust the SWR in this bands? i wait your help. Grazie Murilo
@Nietha-jh6wh5 жыл бұрын
funky junky headbangers balls music
@RichardAdkins6 жыл бұрын
Where did you buy the Teflon guy cable? PLEASE!!! I can not find in the United States.
@iv3tmm6 жыл бұрын
Richard Adkins you can find here: shop.irae2.com
@RichardAdkins6 жыл бұрын
I am sorry, I can not find it on there. If you see it, would you please send me a link to that specific page? Thank you very much!
@iv3tmm6 жыл бұрын
Give me you callsign on qrz dot com i will write to your email
@RichardAdkins6 жыл бұрын
K5RHA
@iv3tmm13 жыл бұрын
Hi Murilo, first of all i thank you for watching my R8 movie then i can say you to tune your R8 antenna ... For 20m band there is no easy way to tune antenna because if: 1) your SWR down point is under 14.000 Mhz then it say that antenna is too long ! 2) your SWR down point is up 14.350 Mhz then it say that antenna is too short ! so to adjust antenna you have to: 1) cut internal coil trap 2) allonge internal coil trap or allone alluminium tube under 20m coil trap
@fifino669 жыл бұрын
Ciao Francesco, complimenti per l'installazione della tua Cushcraft......veramente impressionante la bontà del tuo lavoro.....Sono interessato all'acquisto della R9, (Cushcraft) e volevo chiederti un parere...... Ti ringrazio e 73 da IS0FGC Serafino
@iv3tmm9 жыл бұрын
Ciao Serafino, mi dispiace la R9 non l' ho mai provata. Ho visto e letto solamente il manuale. Francamente, gli 80m super caricati ... non mi sembrano il massimo. Per il resto mi sembra uguale alla R8. Ciao de IV3TMM Francesco.
@fifino669 жыл бұрын
Ti ringrazio, gentilissimo!!!! 73 a te e famiglia e spero di ascoltarti on air!!!!
@RichardAdkins7 жыл бұрын
drive.google.com/open?id=0BzHCj1HvwyywMTh4OXc5eVpLU1k The entire design of the antenna. It's in italian but, omg it is so invaluable. Grazie mille!!!
@RichardAdkins6 жыл бұрын
I am duplicating your design for my R9 antenna. You have designed a wonderful system to stabilize the antenna. GENIUS!
@emmausspy4 жыл бұрын
Bel lavoro . ....... però che musica di mer. .....sotto . Fa venire angoscia...🤪
@mikec95378 жыл бұрын
Interesting install, I'd like to hear you talk about, the music is useless.
@cd11686 жыл бұрын
i like the music..
@epricedtechcom76219 жыл бұрын
The best antenna build is useless if your cable connecting it to the radio is of bad quality.Select great components cables by reading these articles on how to select a good cable epricedtech.com/blog and see those unbelievable prices on Belden RG8X epricedtech.com/Coaxial-Cable-RG8X-RG-8X-Belden-7808A-50-ohm-Low-Loss-RF240-LMR240-LMR-240 and RG6 epricedtech.com/Belden-1694-A-rg6-coaxial-cable-f-connector-75-ohm
@maxmusa86416 жыл бұрын
ciao francesco mi daresti la misura degli stub??? ho del ros e devo tarare entro vreve prima di metterla a palo tetto! maxmusa74 chiocciola gmail punto com , grazie
@RedNeckSurgeyTech Жыл бұрын
You don't know how to use words? To bad. Still shots and loud techno music are not helpful.