How to Build 100W + 100W Stereo Amplifier Using TL084 IC With C5200 & A1943 Transistor

The video Build 100W + 100W stereo amplifier uses TL084 IC with C5200 & A1943 transistor powerful and low noise level.
➤ How to Build 100W + 100W Stereo Amplifier Using TL084 IC With C5200 & A1943 Transistor
➤ Copyright © by Share Tech Creative
➤ Follow me: / sharetechcreative…
➤ Follow Facebook: bit.ly/3eEHjNb
➤ 📺 Thanks for watching!
➤Schematic diagram:
photos.app.goo...
➤ Parts Required:
Transistor:
- 2SC5200 x 2
- 2SA1943 x 2
- TIP 41 x 2
- TIP 42 x 2
- TL084 IC
Capacitor:
- 33p x 2
- 0.1uF x 2
- 0.22uF x 2
- 0.33uF/50v x 2
- 47uF/16v x 2
- 47uF/50v x 2
Resistors:
- 10R/5W x 2
- 220R/1W x 4
- 33R x 2
- 1K x 2
- 1K5 x 2
- 2K7 x 2
- 3K3 x 2
- 5K6 x 2
- 15K x 6
- 33K x 2
- 100K x 2
- 50k x 2 potentiometer
- Aluminum heatsink
- Mica pads x 4
- Diode 4007 x 4
- Diode Zener 15V x 2
- Audio jack connection
- Type Connector 2-Pole 5mm (connecting speakers)
- Power supply:
** +/- 40V DC 10A transformer**
See how to assemble power for the amplifier: • How to make Dual Power...
#diyamplifier #sharetechcreative

[@ShareTechCreative]

See how to assemble power for the amplifier here: kzbin.info/www/bejne/Z2WuYYOrpZdpZrM👈

[@bernardomalomay6288]

Show diaram

[@creative102st6]

It's so powerful!

[@pamornchuawong493]

How many amps is the minimum power consumption? V and A

[@Tariqlhr9]

@@pamornchuawong493 Minimum on 24V this amp working nice and below 24v this amplifier working but sound quality not good. I test with minimum 20v and maximum 34v. I don't know what is the max voltage for this amp. Later I'll test with above 34v and if the circuit will not burnt I'll share my test with you. Over all this amplifier have very good sound quality.

[@Tariqlhr9]

By the way I used LM324 ic in place of TL084 and it's working nice.

[@vincentrobinette1507]

I like it: Since the big power transistors are current driven, there is no need for emitter follower resistors. This output stage is capable of full rail to rail output voltage. The only thing I might try different, is to replace the 1K resistor parallel to the series diodes, with two 500 Ohm resistors. then, I would connect the outputs of the quad OP amp to the junction of the two resistors. That would eliminate any zero crossing distortion, as one diode comes out of conduction, as the other conducts more. If that doesn't work, connecting to the junction of the two diodes, as shown in the video, is always an option. The diodes are necessary, create a current limit, by limiting the voltage that can appear across the 220 Ohm emitter followers on the TIP 41's and 42's. That limits base drive current, giving the amplifier some current protection, in case the output gets short circuited, or, the load impedance being too low. This would be a perfect output stage for a guitar amplifier, if no negative feedback was used.

[@ShareTechCreative]

Many thanks for the information

[@manuelfonseca9937]

Bueno ya lo hice y suena muy bien. . No distorsiona. Excelente. Es mi primer ampli sin PCB.

[@ShareTechCreative]

Yes, thank you very much

[@Creeptonic]

Wow ! this is really awesome. This week has been especially rocking with 2 new designs from you. Thank you again for your hard work to share your gift. Much appreciated. Are you planning to share more Class A designs ? I have tried the 2SC5200 Class A Design and simply love it. Thanks again.

[@ShareTechCreative]

Glad you like them! Of course, please wait for my news. Thanks again!

[@joeyscott4299]

Very nice !!! I love the design !!! I have some tl072 that I will use 2 of for your design . This will be a fun build ! Thank you brother !

[@ShareTechCreative]

Awesome, thank you!

[@jozsefbodor333]

Super!👍👋

[@ShareTechCreative]

Thank you

[@RamirinRamiron-ow9vy]

Buenas noches desde Colombia para agradecer su video lo fabrique y muy bueno lo felicito sabe mucho yo estoy aprendiendo

[@jozsefbodor333]

Super!👍

[@ShareTechCreative]

Thank you very much

[@AHmed.ADam.Reda.00]

Can you explain the AC 2030 with the same sound, this 100 watts

[@bastek.]

Hello. Good idea👍👍👍Have a nice weekend 🙂🖐

[@ShareTechCreative]

Thank you! You too!

[@user-hr6xb7fz5h]

Desde cuba se ve muy bueno.

[@irwandipulukadang3055]

Thx for sharing ... 👍👍🙏

[@ShareTechCreative]

Welcome 👍

[@abdalhamid5636]

Can i use instead of tip bd139 and bd140 transistor my bro...

[@iulianvasile2870]

awesome job. can you provide please the schematic diagram for the full stereo version?

[@ShareTechCreative]

Check description

[@iulianvasile2870]

I've seen that, but is for one channel only. How do I connect 2 channel? ​@@ShareTechCreative

[@ShareTechCreative]

@@iulianvasile2870 If you do two similar projects, it's stereo

[@Tariqlhr9]

Great Video 👍👍👍. Keep it up bro. This time I make no mistake and my amplifier working super good 💥💥⚡⚡👏👌👍😎⚡⚡💥💥.

[@Tariqlhr9]

Last time I was try one of the amplifier of yours. I don't know what mistake I was made , my amplifier was getting hot and I wasn't managed to get the fault but this time in first try ( with same parts which I used in faulty amplifier) my amplifier working 100% nice 💥💥. Thanks bro for such clear and easy instructions.🙏🙏🙏 You are the best 💓💓💓👌👌👌👍👍👍

[@ShareTechCreative]

Good 👍 Thanks

[@kevinbeats1030]

Dose it mean there is a mistake when it gets hot?

[@kevinbeats1030]

Or dose it just mean you need a bigger heat sink

[@Tariqlhr9]

​@@kevinbeats1030 Bro! Of course the amplifier gets hot but there is a limit to how hot it gets. If it is getting hotter than its limit then there is a short circuit somewhere in the circuit. Also sometimes, instead of the whole amplifier getting hot, only one component gets hot (except the main power transistors) and even after replacing that component the fault doesn't go away, it means that the circuit behind that component is faulty. There is no error. However, if only one component gets hot, then it is a fault and if the entire amplifier gets hot within a certain limit, then it is not a fault. In this case you can only reduce this heat away by using a large heatsink.

[@manuelfonseca9937]

Lo hice tal cual pero recalienta demasiado el disipador de aluminio.Que debo hacer al respecto?

[@loverforever4473]

WOOOOOOW good job 👍👍👍👍👍

[@ShareTechCreative]

Thanks

[@singhelectronicsrajound2430]

Very Nice

[@ShareTechCreative]

Thanks

[@richie6920]

Hello, where can I find the diagram of your amplifier, can you share it, please, thank you

[@peteronel4051]

Fantastic amp can you show circuit dia gram not easy to work of cell phone regards. Peter. South Africa

[@gamingcndorito]

It's hard to find the tl084cn, do you think any other op-amp with same pin will work??

[@ShareTechCreative]

You can use the LM324 ic, the functions are equivalent! good luck.

[@lethimaile8355]

Nice 👍👍😁😷

[@ShareTechCreative]

Thanks 😆

[@ourchannel8215]

any ic can be used sir?? TL072 or LM358

[@KOLEJ22DrogaPrzygody]

Hello super video 🎶👌

[@ShareTechCreative]

Thanks for coming

[@RJEDITALL]

👍👍👍

[@ShareTechCreative]

Thank you so much 😀

[@channelvemientay6555]

Great👍👍

[@ShareTechCreative]

Thank you! Cheers!

[@shadisy4145]

Hi can I use tip35 & 36 And What about THD% in this?

[@ShareTechCreative]

Yes you can

[@manuelfonseca9937]

Ouuuuu yeahhhhh!!😁

[@ShareTechCreative]

Thanks

[@Tariqlhr9]

Bro TL084 not easily available in the market and also more expensive ( Approximately RS.100 to RS.150) therefore I used LM324 ( quality and pinouts are same like TL084) but It's much cheaper (approximately RS.30 to RS.45)and easily available in the market or from Scrap ( I get this ic from an old and scrap 18v charger). I don't know what quality is TL084 have but LM324 have very good sound quality. My amplifier is complete now give me the link of your video which have tone and bass control circuit for this amplifier. I mean to say how to connect tone control to this amplifier.

[@ShareTechCreative]

Hello, LM324 quality is excellent! but you use TL084 even better. Thank you for supporting the channel and leaving a comment.

[@kevinbeats1030]

did you use 40V 0 40V 80V as power supply or lower

[@no-mo9gz]

Please make care amplifier

[@ShareTechCreative]

We will try

[@xorochi2183]

Ez jó!🙂👍👍👍

[@ShareTechCreative]

Thank you!

[@JaviersDIY]

This is very awesome sir. I will see you in my channel sir for support.

[@ShareTechCreative]

Ok thanks

[@victorsantanpagay5811]

Is pcb is really hard to made for your?

[@loverforever4473]

Big Liiiiii❤❤❤❤iiiike

[@ShareTechCreative]

Big thanks

[@kevinbeats1030]

whats the maximum voltage for this amplifer

[@ShareTechCreative]

DC voltage max: +/- 45v

[@MAK786GO]

Can i use 3.3omh 5w resistor? On speaker output

[@ShareTechCreative]

No, you can use a resistor of less than 1 Ohm

[@MAK786GO]

So I can use 0.33 ohm?

[@ShareTechCreative]

​@@MAK786GO Yes

[@x2gogo]

Excuse me, can I use the lower noise TL074 ?thank you!

[@ShareTechCreative]

Yes you can

[@kevinbeats1030]

On the 224 0.22uf capacitor what can i use instead cant find that value locally and am almost done with the amp. Please help

[@ShareTechCreative]

You can replace them with the value 0.22uf = 1uf

[@kevinbeats1030]

Thank you will do that

[@rici_21]

If i want to connect equaliser to it, i am connecting it to speakers output ?

[@rk5672]

Schematic diagram link is invalid. Pls. Refresh the link ir upload again.

[@everythingsoftware681]

what can you do to increase the output to 130W

[@ShareTechCreative]

You can upgrade to 8 transistor C5200 and A1943

[@kevinbeats1030]

@@ShareTechCreative okay will try that but don't know how to connect them though

[@alandamianllanes2425]

Cuanta pulgada son eso parlante

[@ShareTechCreative]

12-inch speaker

[@user-hr6xb7fz5h]

Porfabor me pasas el diagrama.

[@teguhariffianto6724]

👍👍

[@ShareTechCreative]

Thank you very much

[@SS-mj2mq]

Yes I would like to know what is the wattage of that zener diode do you know or could you possibly give me the model number thank you 🤗

[@ShareTechCreative]

Diode Zener (0.5W) 15V

[@marlonarias1512]

Me gustaría saber cómo acer una voz ter ampliable para 4 canales

[@ShareTechCreative]

Puede agregar un circuito amplificador 4558 ic para expandir

[@cesarvasconez9481]

Las cuatro resistencia qué dices de 220 ohms son de 22 ohms.

[@ranodyanethmi7541]

LM 324 ai used

[@ShareTechCreative]

Yes, you can use LM324

[@roldaoviana653]

has it mono?

[@ranodyanethmi7541]

+/_32VDC can be used

[@vishanth18]

streo to momo canistion sir

[@gerocire]

el link no funciona Dynamic Link Not Found Short URL (photos.app.goo.gl/owNKrjTCipDx5vEj90) not found If you are the developer of this app, ensure that your Dynamic Links domain is correctly configured and that the path component of this URL is valid.

[@chaudharyonlineprintingpre4455]

Complete price kitna hai

[@ShareTechCreative]

main is empaleephaayar ke lie puraane ghatakon ka upayog kar raha hoon

[@specialistka1]

schemadig diagram please!

[@vineetsharma3735]

make a class a discrete board and vacume tube amp class 50 +50 watt

[@tayfun.b..]

Does it run 12v

[@ShareTechCreative]

Can not

[@zayanshaikh8454]

bro music name

[@lalalazar4639]

You are just making, please tell us the thurie

[@chaudharyonlineprintingpre4455]

Mo no please

[@umeshjoshpin2384]

Vidio not clear

[@nicolasaquino6061]

No puedo entrar en el ling😢

[@cesarvasconez9481]

¡Lo aré y lo comprobare, si no funca..........!

[@ShareTechCreative]

Sigues las instrucciones, funciona muy bien.

[@bernardomalomay6288]

Show me diagram

[@ShareTechCreative]

Ok ok

[@ShareTechCreative]

photos.app.goo.gl/uLTxiBi9qwDrBmMW9

[@bernardomalomay6288]

Diagram show

[@ShareTechCreative]

Yes, please waiting!