I know an engineer who worked in steam catapult development back when the technology was still in its early stages. He told me that the shuttle hooks were breaking from extreme tension imparted on them during testing. So he recommended shot peeing them. They followed his advice and there were no further breakages. Also, I was a machinist and learned early on that anytime you machine down one side of a piece of cold rolled steel it will warp on you as the cold rolling induces residual stress all over the entire surface area.
@electronicsincorp9 жыл бұрын
We are happy that you found our Shot Peening Conference helpful. I would like people to know that we still hold these seminars. You can learn more at shotpeeningtraining.com
@Vinipqs4 жыл бұрын
I used your video to study the process from brazil. Very good.!! Thanks for help
@larryclark93807 жыл бұрын
Excellent video. Toolmaker for 20 years. Didn't know most of this. Subscribed to channel.
@ghffrsfygdhfjkjiysdz Жыл бұрын
Good video, good info. But setting aside the "industrial" requirements for service life benefits can you tell me how glass bead blasting by a DIYer in his garage at say 60-90 psi compares to real shot peening? I realize you can't determine the exact energy transfer in such uncontrolled environment, but is glass bead blasting even in the ballpark of kinetic energies required or would we have to bump up the pressure to above 100psi basically destroying glass beads?
@masonclark80794 ай бұрын
Have you found an answer or help with this? I would love to help if you still need!
@alexnguyen80257 жыл бұрын
thanks for very helpful info, love it.
@Trusty_Steed5 жыл бұрын
Great information and awesome video. keep it up!
@javinino404 жыл бұрын
Thank you for this video, ¿do you have references about the graphs, data or information that you show in the video? I want to learn more about this process for one academic work
@grinchyface7 жыл бұрын
This narrator belongs in an episode of interdimensional cable
@naveensankaran38736 жыл бұрын
Sir I like this video which is very useful.. can u please explain about the below two questions 1. How to plot saturation curve for shot peening process.. 2. What will happen if the shot peening intensity arc value is more ? Can you specify a arc value which exceed will have an effect.. Thank u
@MegaMechatronics6 жыл бұрын
SAE specification SAE J443 will give you the process for plotting a saturation curve. I'm not sure on your second questions, maybe check out this paper: www.shotpeener.com/library/pdf/2016030.pdf
@akshaypathania56805 жыл бұрын
Nice video but my Question is that Why in over coverage of a surface by shot peening there is a decrease in fatigue strength (Any Justification) ?
@masonclark80793 жыл бұрын
Now dont quote me 100% , but i believe it is all dependent upon the material and application. When you are peening a surface, you are removing a slight bit of material and also compressing it in so once your coverage point is achieved and you have overlapping dimples, you're going to start to create stresses in the compressive profile that you built up
@jumpykilllerqx60296 жыл бұрын
So if you going to shot peen do you heat treat the object before or afterwards?
@MegaMechatronics6 жыл бұрын
If you're going up to transition temps then you remove all the beneficial stresses induced by shot peening. However some processes will low temp heat treat, like tempering and burnishing.
@Luistorres-wm4kb8 жыл бұрын
thanks for the awesome info! where I can saftly buy a shot peening machine? and a wpc treatment machine?
@MegaMechatronics8 жыл бұрын
+Luis torres An internet search reveals lots of suppliers who sell shot peeing equipment. For shot media, I recommend Premier but there are other reputable manufacturers out there.