Siemens TIA Portal & Factory IO (How to Display an Analog 0-10VDC Signal / S7 1200)

[@buntofori2768]

Hi, pete, I have watched alot of videos and I can say you’re one of the best. You explained the steps for every zeroes like me can understand. Thanks

7. Let's start with FACTORY IO || Bắt đầu với phần mềm Factory IO kzbin.info/www/bejne/oWfJnpeZn6uDiKs 4. Pick and Place XYZ in Factory IO and PLC || Tay gắp 3 trục XYZ trong Factory kzbin.info/www/bejne/pJauenecbq1rqsk 3. Level Control Analog in Factory IO and PLC || Lập trình ĐK mức chất lỏng kzbin.info/www/bejne/gmm3mqqFjcSXaac

[@PeteVree]

Here is a link to purchase Factory IO. (Note: this is an affiliate link for my channel) factoryio.com/url-action?ref=petervree Full Siemens TIA Portal PLC Programming Course available here: petevree.thinkific.com/courses/siemens-tia-portal-plc-programming Playlist Link for further videos: kzbin.info/aero/PLyL0ResmI4Q2Rz5wtTKWhKhFMLnWU1n6Q

[@adjalkhaled3008]

You are making a great effort. Thank you so much.. 🌼

[@vovk50]

Thank you Pete for all of your videos :)

Thanks bro, it was very clear!

[@framos9991]

Very Useful! Thanks!

[@PeteVree]

Thanks for all the nice comments. Glad the videos are helpful.

[@conradcoetzee9802]

Hi Pete i can't find it but did you ever make a PID control for this

[@PeteVree]

In the online course that I am currently selling.

[@buntofori2768]

Hi again Pete, do u think u could do a complete video of ur assembler manual control ? Thank u sir. Regards Felix

[@LockBai_1989]

Hello sir is there any issue to install this software with my windows10 HOME

[@braincrackz]

hello pete. i am confuse to solve this problem in factory io using s7-300 cpu. do u mind to make a brief discussion about this tank level that is ID100 ( real ) because i am using comparators command ( dint) because if i use real it turns red. thanks

[@aamirawan7998]

BEAUTIFUL

[@komyothu1570]

Beautiful

[@zhuj.y.8903]

Your previous video NORM_X use Int to Real such as %IW64 (Range from 0 to 27648) but why in this video you use Real to Real and fill with %ID112 which range is 0.0-10.0? How about %IW112 but Int to Real and 0-27648???

[@TheGazanews]

Hello Pete, although the Rajvir Idea has worked, still didn't get why that input didn't get the value from Factory IO ?

[@PeteVree]

Not sure why that conflict happened either.

[@ahmedhamdybjr6462]

very helpful Video As Usual. I see the problem like offsetting the I/O Addresses for 0 to 10 and you should do the same for AI addresses on PLC , because the floating voltage on TIA Portal is coming from the PLC I/P not from Factory I/O. I am learning from your good videos along with Rajvir Singh videos at the course..

[@PeteVree]

Yes. The analog signal messed me up for a while. I often overlap various words in my programs as they get larger as well. Reinforces the fact that we should create a spreadsheet for all bits, words, and dwords as we develop our programs. Thanks for helping me learn as well.

[@chuchuokeke]

are the contents of network 1 necessary to start the tank fill proces and discharge valve process? you didn't share network 1☹

[@PeteVree]

Network 1 was just a simple 3-Wire control that turned on a "Sys Run" Bit, that controlled a green and red light. Here is a new video that might explain things better: kzbin.info/www/bejne/imrOgZeLqbyNkNk

[@lukaskolodziej2928]

You are make mistake about ID100 because. You setup your analog imput on PLC 1200 on start IW100. In program starting reading your analog input 0-10V not from factory I/O but from PLC and even not corect becouse from PLC going anlog synal intiger and occupying one word.Thanks for lesson. This program is very nice for beginer and I can learn and practice.

[@adjalkhaled3008]

But you don't have QD112 in the plc so it should be an error

[@gwenettedot23]

may i know what software you used for your 3d presentation?

[@PeteVree]

The simulation software is Factory IO, a phenomenal program. link: factoryio.com/?gclid=CjwKCAjw1rnqBRAAEiwAr29II1x5J53juTC3-Htk_tGQqbKrj7OD0XX32vu4V6cThat3FdNDSgHH6hoCfA0QAvD_BwE