Sigma Max Tile Cutter - Push Type Sigma

[@robertgoss878]

It is still a push cutter with the handle set the way it was. Sigma makes There cutters where you push away from the fence. That way your measuring scale is closer to you and easier to see ,otherwise the numbers on the scale are upside down.

[@meckanicall]

If you do it the way you suggest by pushing it as it is supplied, you will almost certainly push the tile away from the scale bar-stop and a bad cut will ensue. I agree though about the numbers being round the wrong way AFTER changing the cutter direction. In practice you can easily get enough downforce, even on the pulling action, without needing to swap the cutter.

[@DPJOINERY]

I prefer to use mibe the otherway round, so in theory no need to change the handle round as he does in the video. Reason i prefer to cut this way is because the measuring numbers are the correct way and much easier to read.

[@climbjay]

Yep. Same.

[@matthewlall4277]

I just received my first Sigma after having it ordered five months ago. I ordered the max series in the size that would cut common 24" tiles. The cutter came 26" 3B4 with a pull handle. In the box was a max handle as well. I have no issue with swapping out the handle, but a couple of things bothered me. First, the guide bar was dinged up and had burrs on it's tile side edge. One stuck in my finger when I ran down it...second, the max handle had aluminum shards all over the bottom with manufacturer burrs that weren't cleaned up. My final gripe is my cutter has no support arms. I realize it's a 26" cutter, but why break out the big boys when the majority of plank cuts are cross grain. I run Ishii 29", Superior 17", Felker/Rubi ts 30, Rodia 75, the new Montolit 36" P5, and the RTC 53" Razor. I always wanted a Sigma and feel disappointed with what came from the factory. I tried it and it does cut very well. My beef is with the quality control and lack of support.

[@LosmiPZS]

Is it possible to rotate the scale not to be upside down?

[@Mzraveski]

I'm an apprentice and everytime I try to snap the tile I chip it. And it's really fucken frustrating. Any advice?

[@hotdog7988]

are you using a sharp wheel and scoring the tile hard once paying special attention to the end corners?

[@hotdog7988]

and pressing evenly in the centre of the tile

[@Mzraveski]

Yea I'm using a sharp wheel but I get told sometimes I'm pressing it to hard

[@hotdog7988]

@@Mzraveski so, it's chipping as you scribe?

[@Mzraveski]

Not all the time only sometimes. But since yesterday I think I'm getting the hang of it 🤷 I only chipped once yesterday

[@paolobenmore3504]

Concerning cutting blades. Does this product come with different blades or is it one blade cuts all?

[@matthewlall4277]

Not sure the sizes, but I do know the wheels are not the same between the push and pull handles.

[@kar15bigdog]

How much is that 1 ????

[@laurenprincehouse]

This worked great for redoing the shower/bathtub of my kid's bathroom. kzbin.infoUgkxfiuHoZJo3bgdVPFRxQ-iqPpfbEHl2cYt I didn't like the guide, so I took it off. I just used a fine tipped sharpie on the tile and followed that line. It does make a wet mess, and once I started looking like I wet myself I started wearing a towel and apron while cutting. The blade it came with worked great until we wore it out. It was better than the replacement one we bought. I tried looking for just their blade, but failed. Not really for larger tiles unless you stack stuff on either side to support the tiles. Anyway, would definitley buy again.

[@johnnybear111]

is it designed to only be pushed?

[@centuratoolsaccessories847]

It can be used either way! Most people who purchase this unit buy it for a push method but if is possible to use it as a pull type as well.

[@jackofalltrades4091]

Why didn't this come in the push orientation, took me half n hour before I found this video

[@dantruong2582]

Seems to be a little confusion why you want to change it around. Pulling is easier to use. Pushing is for more power in scoring harder tiles like glazed porcelain.

[@mosconi4539]

Can you doi it with the 3C2 model?

[@TileNation]

You do not need to change the handle. in reality it is much more ergonomic to leave it as the factory sent it out. Thanks

[@DEXTER941]

Who came up with the idea of playing music across someone talking, very annoying when you are trying to hear someone properly. If you really have to play it, at least tone it down so we can hear what the guy is saying.

[@luispila4749]

Donde seccompra estas maquinas

[@mpirokajosephmgcokoca2355]

Excellent 👏

[@mohammadusmanmohammadnoman8496]

Price

[@robertmontoya7300]

Qué medida es la

[@alexanderlerke9589]

Hallo. Du hast den Schneid und Brechhebel falschherum montiert.

[@grahamkirkwood8683]

Can you use this as pull

[@centuratoolsaccessories847]

Yes, a lot of people do use this as a pull. In fact recently we have heard most people prefer it.

[@Ciuf84]

@@centuratoolsaccessories847 and this is available for any Sigma model ,to turn the handle???Why do I ask, because this year I took my Sigma 3D4, and I can not get used to pull!!!

[@centuratoolsaccessories847]

@@Ciuf84 yes, you can purchase the “Max” handle to turn your cutter into a push option on our website here: www.centuratools.ca/en/sigma-push-handle-for-3c3m-3d3m.html

[@Bbbbbbbbbbb-f1w]

Make no fucking sense. Some people are so stupid. It says “push handle” but the video shows “pull handle” then it says you have to “buy” the MAX push handle seperate

[@kingeleven3820]

Im left handed i prefer push

[@javiermenadavila6848]

Necesito la presentación en español

[@future_phonk]

You should give one to the "they gave it to me" tiktok guy.

[@احمدتركي-ن8ت]

انا استخدم هذا النوع انهو جيد جدن

[@mohananuragi2821]

Catar ka Kya name he kitne price hai please Bai ret batana

[@الغزيالغزي-ل7غ]

السلام عليكم اخي ممكن تكلي من وين اشتريته هذا المقص وكون ممنون منك

[@pf5658]

Too many parts that can easily get lost IMO.

[@noelmadden1920]

Why would anyone want to work with the squaring bar the opposite end to themselves. Daft video.

[@cdragon222]

Wrong way

[@PawanKumar-kz5vl]

Sr praaij