Heat Molding Bont Cycling Shoes | Sigma Sports

[@timo_kami]

I'd recommend molding your shoes after a ride or at the end of your day as your feet swell. The shoes will be molded to accommodate this.

[@camaroblackmatte]

the best short tips & tricks on heat moulding shoes ...my inline shoes will be so great after this :) thank you !!!

[@pukki34]

Actually a good video about the procedure, thanks !

[@sigmasports]

pukki34 Thanks! Glad you found it useful.

[@MarshallMotorSport]

Do you tighten the boas when its hot or will this damage the upper of the shoe?

[@hamishreilly3519]

Hi, do you know what gas mark I should set my oven to as it is gas, or is it not doable?

[@mdtaylor2274]

Do you think these would suit someone who has reversed arches, such as Charcot Foot?

[@lukaslamla4981]

Hi there, nice video - I have just bought riot mtb+ and the arch support is too large for me - do you have any experience how much the moulding could move the arch down? Is it just 1-2mm or maybe 5mm??? THX!

[@sigmasports]

Hi Lukas, Thank you, if you could please drop [e-mail] an email and they will be able to help you out. Thanks, Lucy

[@torreslondon7541]

Before putting the warmed-up shoes back on for moulding, did you put the insoles back in?

[@sigmasports]

Torres London Yes, replace the inner soles before putting the shoes back on. Sorry, we forgot to mention that!

[@EnergiBornholm]

Hi there....Just got the shoe from you.... Can I make the shoe 0,5 cm wider for my big toe ??? And how ??? Been in the oven for a 20 min an 5 and 5 at 70 C, its not able to do molding.. ? Regards Flemming

[@cmilz4306]

If you have the boa system do you have to remove it?

[@sigmasports]

No, you do not have to remove it.

[@blqckstars4176]

Hi for Bont Mtb+ do you need to remove the metal screws on the lugs. Thanks.

[@sigmasports]

Hello, You shouldn't need to, but please be aware that these may get hot. However, you do need to remove the innersole prior heating them. I hope that helps! Thanks, Lucy

[@sigmasports]

Looking to buy a pair of Bont Cycling shoes but aren't sure how to mold them? kzbin.info/www/bejne/eJXNonWYd9iabbs ‪#‎cycling‬ ‪#‎ridelots‬ ‪#‎bont‬ ‪#‎molding‬ ‪#‎custom‬ ‪#‎vaypor‬ ‪#‎zero‬ ‪#‎blitz‬ *****

[@Pepepepino8989]

What temperature it's to use and how long leave them inside?

[@dermeister314p]

Was this done at the flagship store at 37-43 High Street Hampton Wick? I need help with my Bonts...

[@sigmasports]

Allister L Yes, this was shot at Sigma Sport in Hampton Wick. Drop by the store and a member of staff will be happy to assist.

[@82vitt]

A major problem with Bont shoes seems to be inconsistent sizing across the range of different models. My Bont Vaypor size 43 are noticeably smaller than my Vaypor + in the same size. The Vaypor also have much tighter heel cup right out of the box. Obviously, in the case of my narrow heels, the sides of the sole can be squished to make it narrower as you present in the video, but then that causes the sole to elongate a bit in the top of the back area...

[@dhyrk3]

After heating the shoes, how long before you put the insoles back? On my first Bonts, I placed it right after then mould, but the insoles shrank! I have a new one coming. How do I avoid it from happening again? Thanks

[@stevec2739]

That’s a pretty brutal way to do it, better technique instead of the screwdriver is to tissue pad them when hot, we have been moulding carbon ice hockey skates for years, look at the tips on True ice hockey skates, have done umpteen pairs and when you get it right they fit like a glove.

[@aomana]

Using the shimano oven to promote other brant, that's no good...

[@jeremys2159]

Wait, which guy was Brant?