Silverwing sliders and belt

[@adventurekevin9409]

Well explained video. Just installed these Dr. Pully 26g sliders this afternoon. It was nice having this video to follow. Thanks for taking the time to explain and post.

[@IamIronWolf]

Thanks. Riding a 2012 Shadow now, but looking at a 2002 SW for day trips for both of us. I also like the storage as I only have the bike (wife has a cage) & I do the grocery runs. The SW sounds like a good all arounder for town, local touring together, & some 1-up extended tours. Looks easy to maintain too. That way I could set up my Shadow Aero as a solo cruiser & do other stuff with a SW. Appreciate the quick response.

[@tcalof]

2 up at 430 lbs at 70-75 mph is no problem. The Swing is rated at 375 lbs. I would suggest bumping up tire pressures to 30 front and 38 rear. Set the rear shock preload to 5, the firmest setting. A set of front progressive HyperPro springs eliminates dive on braking, and the Swing is more stable during undulating road surfaces when cornering. Dr. P sliders increase acceleration, lower cruising rpm by 500, and reduce belt slap and vibration.

[@MrDavidelliottjr]

Where can I get these sliders and belt

[@discoverall2007]

There is an easier way to torque the variator by pulling out the outer drive face of the clutch, so the belt can get enough room on the variator side.

[@joaquinpinon2872]

Awesome information 👍🏻

[@mykuljay]

This was just terrific! Thank you. Looking at a used Silverwing tomorrow!

[@tcalof]

You're welcome. The Silverwing is a great, reliable scooter.

[@tcalof]

I opened up my belt case recently after about 3k km, and I noticed no extra belt dust. The case was fairly clean and the belt case air cleaner was not very dirty. I'm not sure why you would suspect the Dr. Pulley sliders of causing extra belt wear. Above 4000 rpm, the belt will ride higher on the front drive faces than it will with the stock rollers, causing your cruising rpm to be lowered by about 500 rpm compared to the stock rollers.

[@MadsWorld34]

glad I found you here I just got a silver wing and hope I don't need this step for awhile but I know in time I will and will come back and watch it

[@TheGamersRace]

I just want to point out to anyone purchasing a new CVT anything should check the life of the belt. Some of these maxis are approaching 20 years old now, even if the belt doesn't have miles on it some of these belts are going to far exceed the recommended life of 2 years. And with age comes dirt and dust, which can equally deteriorate the performance and life of the components in the CVT. Do your future self a favor and at least take 15-30 minutes to take the cover off and, at the very least, inspect what you're working with on your new scoot. Belts, weights, cleaning, etc it's too cheap and easy to not do if it's needed, and sometimes even if it's not. I've done this, and just to find that a perfectly good running scooter had terrible grime and a slash in the belt! It was ready to bust and it wasn't having any more. TLDR: This shits too easy to skimp out on just take the cover off and have a look.

[@keithroberts331]

Thanks for sharing very informative .

[@IamIronWolf]

How is the SW for 2 up adults for day touring? About 430 pounds people & gear, back roads and some highway (70-75mph)? Is it doable? Very informative videos. Appreciate it. Oh, and what gains from the Dr. Pulley rollers? Thanks.

[@Bud_51]

Don't hold the outer cone as you tighten the bolt, the belt will climb the pulley as it gets tighter automatically...

[@TheGamersRace]

I just want to point out to anyone purchasing a new CVT anything should check the life of the belt. Some of these maxis are approaching 20 years old now, even if the belt doesn't have miles on it some of these belts are going to far exceed the recommended life of 2 years. And with age comes dirt and dust, which can equally deteriorate the performance and life of the components in the CVT. Do your future self a favor and at least take 15-30 minutes to take the cover off and, at the very least, inspect what you're working with on your new scoot. Belts, weights, cleaning, etc it's too cheap and easy to not do if it's needed, and sometimes even if it's not. I've done this, and just to find that a perfectly good running scooter had terrible grime and a slash in the belt! It was ready to bust and it wasn't having any more. TLDR: This shits too easy to skimp out on just take the cover off and have a look.

[@herkko61]

Excellent tutorial!

[@ebeperez1982]

Hello Friend. You can give me the dimensions of the holes in this key to hold the wheel. Great way to check but I have to make a key like that. Thank you for your help, best regards.

[@seeker9969]

Nice video did u by chance have a video of u taking the wing apart to that point

[@tcalof]

No video, but just download the service manual. You can find it available for free all over the 'net. It isn't hard at all to get the plastic off.

[@7316bobe]

Good video well explained and nice detail.

[@starbarrothschild6597]

viewing in October 2021, thanks for posting.

[@davidalder6558]

Why did you change the rollers to Dr. Pully sliders? I guess I missed something. Thanks for the great video. Dave

[@tcalof]

The stock rollers cause belt slap and vibration. The stock rollers also aren't the best for responsive acceleration. Read about them on the Dr. Pulley website.

[@gatewaytothesky]

thanks you made it seem so simple

[@kingovthejungle]

nice video , having my bellt changed soon , good to know how its done!

[@charlesgregg8633]

Very detailed well explained Video

[@tcalof]

No. Any lube will collect dust and eventually gum up the action of the sliders, causing them to stick.

[@JohnSmith-uy7sv]

Great video....however.. I have no information as to why you were replacing the belt and rollers. How many miles does the belt last? Like tires... I hope not. Like a motorcycle every 5-6K. I'm thinking about getting one but need to know the mechanic's of it and how often I would have to do maintenance and change belts and tires as I have back problems. Is the engine and cooling system pretty much like servicing a regular motorcycle? Thanks.

[@tcalof]

I replaced his rollers with sliders because he wanted the reduced vibration, increased acceleration, and lower cruising rpm that sliders offer over stock rollers. I replaced his belt because his old one was nearing its EOL (end of life) based on mileage.

[@JohnSmith-uy7sv]

You mean it can handle only 15K wear and that's it?? Yipes. I love the drive shaft. This is worse than a chain sound like. How many miles does the belt last and tires too. Thanks

[@tcalof]

John Smith The belt should go 16k miles. Tires? Depends on your driving style, inflation, speed, and load. They can go anywhere from 5k miles to 15k miles. Scooters eat tires compared to motorcycles, as the scooter tire is smaller and works harder.

[@JohnSmith-uy7sv]

tcalof Thanks for the info. I always babied my bike's even the Goldwing I had and never could get more than 5 or 6 k out of a rear tire. What is the engine like....much maintenance? This seems to be like a over glorified mini bike clutch system. :-) Thanks again.

[@tcalof]

John Smith The Silverwing's CVT is much the same as a minibike, snowmobile, or car CVT. They all work on the same principle. The Silverwing engine has very little maintenance, just like the Goldwing. You will find the Silverwing air filter way easier to change than the Goldwing's. The GW air filter takes hours to change, the Silverwing's only minutes.

[@atemarzvlogs1503]

Olala very nice new here

[@The1belal]

Great tutorial, thank you

[@rafi62605]

Hi, same bike,needing to replace the fuel door , were do i begin pls

[@knowone6214]

did ya grease the needle bearing???

[@tcalof]

It was 11 years ago. Do you think I remember? LOL

[@juanjodominguez18]

Muy buen tutorial mil gracias👍👍🇪🇦

[@pierrebers4740]

Good video! And the results? Is it worth it to change the rollers against the Dr Pulley blocks? My Sliverwing is 18 years old.

[@tcalof]

I would say it is a good idea. There will be less vibration from the belt, no belt slap, and acceleration is stronger and smoother.

[@pierrebers4740]

@@tcalof Thank You for the answer!

[@tundralane256]

Hey Terry. would this improve my mpg? should i go OEM rollers and belt, or go with sliders and oem belt? looking for my 45mpg again, and faster acceleration. it has dropped to around 38ish, and has just under 10k miles, 2013, already have fresh oil, battery filters, brand new oem irc tires, thank , Ricky.

[@tcalof]

Hey Ricky. I would recommend the sliders and OEM belt for better acceleration and less vibration from belt slap. Have you done a throttle body synch? It's quite remarkable how much smoother the engine will run with the synch. You need a throttle (carb) balancing device to do that.

[@ronaldom5429]

Thanks for the good instruction !

[@burnhamben1]

Can you tell me if there is a On/Off switch on the light in the trunk?

[@tcalof]

I had installed a switched light for the trunk light. Before, the light came on whenever the trunk was opened. The switch was from an older Honda Civic dome light. The switch was a combo light/switch. Perfect fit.

[@1980nghia]

Hi, can I ask what do you think about the aftermarket kevlar belt as well? thanx

[@tcalof]

I would stick to the OEM belt. I have heard of aftermarket belts delaminating and failing much more often than genuine Honda belts.

[@1980nghia]

tcalof thanx for your reply, do you know the part number for the OEM belt? Thanx again.

[@tcalof]

Nghia Nguyen 23100-MCT-003, cost is anywhere from about $105 US and up.

[@1980nghia]

tcalof cool thanx. So it is the same as the previous model FSC600

[@tcalof]

Nghia Nguyen I believe the belt number hasn't changed over the years. It's best to search the part # for your year of Silverwing on any Honda online parts retailer.

[@jaybyrd5556]

Nice video thanks

[@superspecialty5169]

All right, a nonfacial recognition video, only subject matter info! 👍

[@robertsineath8329]

Do you know what size car tire will fit a 600 Silverwing?

[@tcalof]

No idea. I would never put a car tire on any motorcycle or scooter, but that's me.

[@juanjodominguez18]

Buen vídeo, gracias.

[@abdallahbidawy2211]

my stock silverwing 600 has 35g rollers. is that normal ?

[@MrDavidelliottjr]

Also is 26 grams ok for all Honda silver wing? I have a 09 fsc600d none abs

[@tcalof]

Yes, 26 g is OK for all Silverwings

[@ES1KPO]

if speed is about 60kph and remove both arms from the handlebars, handlebar not wobbling ?

[@tcalof]

Depends on tire wear and inflation. New tires shouldn't wobble. Try raising tire pressure front and rear by 5 lbs.

[@ES1KPO]

tires is new..drive.about 300km front michelin, rear dunlop. may be reason is one traverse, not two like motorcycles and too short ?

[@tcalof]

Did you balance the tires?

[@ES1KPO]

yes, of course :). and pressure is front 2.0 rear 2.2 bar like in owner manual . By adding pressure 5lbs.... i can,t find what is 5lbs to bar-s, we have here a european units :P

[@tcalof]

5 psi = .34 Bar. Google is your friend.

[@MrDavidelliottjr]

Where can I get these parts? Belt and sliders.

[@tcalof]

Sliders from here: www.partsforscooters.com/169-438-Dr-Pulley-28x20-Sliding-Roller-Weights or eBay, belts from any Honda motorcycle dealer

[@aryenoam]

very good video.in my silver f1 flashing 2 short wat is that say

[@abbaskazem-b8g]

Orginal is 27g

[@vher143]

you are trying to damages the belt, wrong way of installing the belt

[@tcalof]

Only if you live in the Southern Hemisphere. There everything spins counter clockwise. Coreolis Force, you know?