Riden RD6018 Boosted With This 65V AC/DC Power Supply!

[@Mandrag0ras]

This thing was Bangedgood. They did quite the impression from the get go.

[@FusselCNC]

i have a 1,8kohm 5W resistor on the AC/DC PSU. The noise is gone.

[@DevelopWithDan]

Rookie KZbin mistake :-). You are supposed to look up the resistor value offline and then point out the colors and just pretend like you knew it off the top of your head. Great review though.

[@SimpleElectronics]

I have a chart on the wall :)

[@matheokoning4456]

I have the rd6006p since today and I hear a faint high pitch sound when I turn on the voltage output. The sound becomes less when I increase the output voltage and from 35 volts the sound is gone. Do others have this too? Or is this a defect?

[@Pawel5837]

It will rise your current over the switching PS specs. Just keep your power below the specs. In my 1,38 software version there is power limit setting. However voltage is limited about 1volt below your PS specs.

[@change_your_oil_regularly4287]

R4850G2 + "rectifier module" + can-bus controller. Can run multiple frontends from single psu.

[@ninjutsuryu1161]

Nice video, but the floating head in the beginning is just weird :-)

[@SimpleElectronics]

Less weird than seeing my reflection, which is what this is blocking

[@AndrerwBurrows]

Its a buck converter 12amp at 60 odd volts will power 18amp and lots more at lower voltages

[@dermozart80]

Got mine today and I got the exakt same bend corner in the power supply. Oh and I also managed to directly cut the warranty label O.o

[@snivesz32]

What is the max current it can deliver at 12V? Why?

[@bwselectronic]

Chances are if you're using that power supply you're gonna need some light. I would use it to power LEDs for light and that might be enough to quiet it down.

[@SimpleElectronics]

This is what I was thinking too!

[@philhunt1442]

I'm just looking for a power supply to anodize some logos onto my titanium parts, and what does all this mean? Where can I learn?

[@alexstone691]

A high quality power supply would have inrush limit so there would not be a spark when plugging it in

[@sunuk1915]

It's awesome power supply series, I think they needs to develop electronic load controller

[@SimpleElectronics]

I agree!

[@abeleski]

You got a BANGed up p/s from BANGood and you are surprised? Its in their name...cmonnnn

[@seanstraw8688]

They don't call 'em BANGGood for nothing. There's no reason to believe that the bent tabs on the PSU happened during shipping. The white (in your case) potentiometer to one side of the output terminal strip allows you to adjust the PSU DC output. a switchmode PSU shouldn't be producing a lot of heat. A decent 48V PSU can generally be adjusted up to about 56V or so. Try a Cosel or Meawell PSU sometime. Also, consider this: cut an opening in your workbench and mount the Riden down into it (facing up), and have the PSU under the bench somewhere.

[@fredflintstone1]

As DiodeGoneWild would say most probabley Dodgy Chinese PSU :-)

[@3d4arab]

I think the bend is intentionally exist for some reason, it exist in all youtube video and of course mine

[@sunuk1915]

Right sides diode where big inductor

[@sunuk1915]

Input 1.1:1 output voltage ratio

[@kefler187]

It got banged good XD

[@andyapple9]

Crank up the voltage to 68V and the noise will be gone.

[@psvyme48paulh45]

Cool 🇬🇧👍

[@HDXFH]

Whats with the nick cage meme lol

[@tamtgirl]

those big caps were in the input! NOT great esp in 240v countries! caps go BOOM! even at 120v, the p-p volt is too close

[@MarshaJ8800TU]

They probably get switched to being in series when switched to 240

[@simontay4851]

Of course they are in series when its switched to 240V. This looks like a half bridge design.

[@robertalabla]

They look like salvage rewraps due to the black plastic discs covering the vents.

[@rilosvideos877]

These cheap chinese SMPSu's normally don't meet their specs. If you run it for a long time at max. power you will probably burn something, the switching Mosfets or the output diodes most probably. Often the heatsinks are not sufficient or badly mounted. The RIDEN Buck-converter probably does a good job. I have the DPS5020 for 2 years and use it on a daily basis with my little PV-panels. To power it from solar makes sense and the input voltage range is just great for 2 bigger panels in series.

[@darkness1943]

Oh yes 11 Amps from power supply for an 18 Amps RD6016... Very smart mr. clever 🤦🏻 👎🏼👎🏼👎🏼👎🏼👎🏼

[@SimpleElectronics]

Maybe you should look into ohms law. 11 amps at 65 volts allows you to have 18 amps at lower voltage. I don't think I'll ever need 10+ amps at 50+ volts, if you do, then pay more than double the price for a power supply capable of it

[@darkness1943]

or somebody is clever enough and use two of this power supplies and use it parallel and better the RD6024...