Does your status indicator show undervoltage flash senquence when you turn off the power to the unit?
@wildcatwilly Жыл бұрын
I believe it does as the voltage drops out of the capacitors.
@marciomaia40202 ай бұрын
Will this work on a 2hp general purpose single phase motor?
@wildcatwilly2 ай бұрын
No the motor has to be three phase to manipulate the speed.
@DarveshKhan-j5d2 ай бұрын
This motor says it runs on above 200 volts but you gave it connection of 110 volts how is that possible will not motor burn out?
@wildcatwilly2 ай бұрын
The vfd stores energy. It will compensate for it.
@DarveshKhan-j5d2 ай бұрын
@@wildcatwilly can you suggest me kb drive for half hp motor
@wildcatwilly2 ай бұрын
@@DarveshKhan-j5d this same one will do it. Just by changing one of the jumpers inside.
@PeterHatch-mx7zcКүн бұрын
Where do I buy them
@wildcatwilly2 сағат бұрын
@@PeterHatch-mx7zc state motor control
@TractorWrangler013 ай бұрын
Will that run a 110 motor?
@wildcatwilly3 ай бұрын
The vfd can run off of 110 volt. To manipulate the speed you have to have a three-phase motor.
@TractorWrangler013 ай бұрын
@wildcatwilly Thank you for the response. We have a 110 motor that can be converted to 220, but that would still be a single phase right? Still no good.
@wildcatwilly3 ай бұрын
You're very welcome. Yes unfortunately that will still be single phase for you.
@wildcatwilly3 ай бұрын
You can buy cheap 3-phase motors offline I would estimate about $180
@magayver777 Жыл бұрын
Hi good evening. I am looking for a VFD for the motor below. RPM: 1750 VOLTAGE: 115/230 2 HP FREQUENCY: 60 PHASE: 1
@wildcatwilly Жыл бұрын
Message me on Facebook
@viliuspocius4383 жыл бұрын
Just put a capacitor and it will go
@d-arts71398 ай бұрын
im learning, and trying to buy a belt grinder in my price range. im looking at frames with and without motors, vfd's, ect., and may end up buying these components in stages. i want variable speed. thats for sure. i dont know that much about electrical. so, neither the KB 24D or 27D will run a single phase motor? i was getting the impression from another guy that with 115vac from the wall to a single phase motor, i could just get a dimmer switch from home depot to control the speed. ive since found a deticated "vari-speed" switch online, like a dimmer switch but with heat-sinking fins. but would the dimmer switch not be as smooth of power delivery? be jumpy? i dont need fancy but i do want a smooth belt speed. id like 2 horsepower as well and about 3500 rpm max. energy effenciy isnt a priority. suggestions?
@wildcatwilly8 ай бұрын
I'm unfamiliar with the dimmer switch method but it sounds like it would work might be worth a shot or you can buy once cry once. You going to make the decision brother.
@d-arts71398 ай бұрын
@@wildcatwilly yea, vfd's. where were they a few years ago. i just dont want anything i dont need. im sure people were controlling the speed before vfd's were necessary and required... demanded! YOU MUST BUY A VFD YOUNG MAN! oh well, ill find what im looking for eventually. thanks man
@wildcatwilly8 ай бұрын
Back in the day they would use DC motors to vary the speed check eBay maybe
@d-arts71397 ай бұрын
@@wildcatwilly yep! im learning all about that now.. permanant magnet PM motors. DC motors. youre right. lots of rotary switches in the market for DC motors. some start with AC from the wall and switch to DC for the motors. im getting the impression DC motors might have a lot more torque. anyway, DC or PM motors are big and heavy. with the tilting 2x72 frames im looking at theyd be to big at 1.5 or 2 hp.
@wildcatwilly7 ай бұрын
I'm not sure what you're budget is but if you send me an email I can send some links that would help for reasonable prices
@JR-ly6bx Жыл бұрын
looking for a VFD for a blower motor with a capacitor, any suggestions?
@wildcatwilly Жыл бұрын
I'm no electrician but I don't think any vfd motor will have a capacitor because they are three phase...
@JR-ly6bx Жыл бұрын
@@wildcatwilly thanks, i meant my motor has a run capacitor, is there a vfd for this situation
@wildcatwilly Жыл бұрын
As far as I understand it you can remove the capacitor from a single phase motor and convert it to a three-phase motor and use a vfd to power at and manipulate the speed.
@S30Build Жыл бұрын
Any idea why the breaker trips when i connect my ground from the 3ph motor to the vfd but runs fine when i disconnect the ground?
@cablemanagement1524 Жыл бұрын
is it a gfci breaker? a vfd output is pulsed, and the pulses induce high-frequency currents in the frame of the motor that then travel through the ground, and gfci outlets/breakers don't like that. they detect the currents and shut everything down. i wouldn't know how to help if it's just a normal breaker but i definitely have experienced immediate shutdowns when i have connected vfds to gfci outlets in the past.
@cablemanagement1524 Жыл бұрын
these currents can also come out in the shaft and shock you, if the motor is very small
@S30Build Жыл бұрын
@cablemanagement1524 Yes, i have an af/gf breaker on my garage circuit. i ended up changing the switching frequency of the kbac-24d by moving jumper j12 from 8k to the g2 sensitive jumper position for gfci. That fixed the breaker tripping, but the motor makes more of a higher pitched sound when running...
@cablemanagement1524 Жыл бұрын
that's interesting, i didn't know you could change the carrier frequency on these drives. and yeah, the carrier frequency noise is part of the the trade-off. glad it fixed the tripping, though. i personally haven't worked with these KB units, although they look extremely solid. i use a Fuji Electric unit, which has an interesting feature that allows you to scramble the carrier frequency to make it sound more like white noise. the drawback is that the Fuji units are NOT nema 4 rated and they DO require programming and tuning. although a nema 1 conduit envlosure box can be purchased and installed.
@wildcatwilly Жыл бұрын
Very interesting
@paulcottingham241 Жыл бұрын
can be ran?😅
@wildcatwilly Жыл бұрын
Yes it can
@diymaniac8762 жыл бұрын
I have a 110v 3/4hp 3450rpm, single phase motor, on a belt grinder, this is perfect, how can I get 1 ?
@wildcatwilly2 жыл бұрын
You will have to have a three phase motor.
@wildcatwilly2 жыл бұрын
Can you message me on Facebook?
@billystray70072 жыл бұрын
No programming ?!!!!! I have recently purchased a 7.5hp 3phase 24" planer, and for God sake I just want to do a simple phase conversion ..
@wildcatwilly2 жыл бұрын
Yes sir no programming. I sell complete units if interested.
@billystray70072 жыл бұрын
@WildcatWilly what should I search on your website based on my needs ?
@wildcatwilly2 жыл бұрын
Can you message me on facebook?
@billystray70072 жыл бұрын
@WildcatWilly I dont have a FB account Let me see if I can use my wife's phone
@wildcatwilly2 жыл бұрын
I'm getting ready to leave for the weekend but I can get you fixed up probably Monday
@drabusharr Жыл бұрын
New motors cost less than the vfd
@wildcatwilly Жыл бұрын
That is an accurate assessment... However you will not be able to vary the speed...